11 Airworthiness Directives: 5 airplane, 3 rotorcraft, 3 engine.
AD 2026-22-04 · published Nov 2, 2026, effective Dec 7, 2026
The Boeing Company Airplanes
The FAA is superseding Airworthiness Directive (AD) 2023-07- 09, which applied to certain The Boeing Company Model 747-400 and -8 series airplanes. AD 2023-07-09 required inspecting for wear of the transfer pump housing inlet check valves and transfer pump motor impeller inlet adapters for the horizontal stabilizer fuel tank and doing corrective actions, if necessary, and limited the installation of affected parts. This AD was prompted by the manufacturer developing further action to address the unsafe condition. This AD requires repetitive inspections for damage of the transfer pump housing inlet check valves and transfer pump motor impeller inlet adapters for the horizontal stabilizer fuel tank and applicable on-condition actions. This AD also limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-05 · published Nov 2, 2026, effective Dec 7, 2026
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by a report that, during production, certain sealant installations within the center wing fuel tank did not receive required visual and adhesion inspections. This AD requires a detailed inspection of certain sealant installations in the left, right, and center wing side-of-body areas, an adhesion test of the sealant, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-06 · published Nov 2, 2026, effective Dec 7, 2026
Diamond Aircraft Industries Inc. Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Diamond Aircraft Industries Inc. (DAI) Model DA 40, DA 40 F, and DA 40 NG airplanes. This AD was prompted by several reports of passenger door separation during flight. This AD requires revising the existing airplane flight manual (AFM) to provide the flight crew with revised operating limitations, emergency procedures, and normal operating procedures; inspecting the passenger door latching mechanism and safety hook mechanism areas and performing corrective action, as applicable; inspecting the safety hook, latching bolts, front and rear door guide blocks, canopy and passenger door warning light, carbon hinges, tension spring, retaining block, safety hook push button, latching mechanism spring, gas spring, and door frame; measuring the passenger door handle actuation force; modifying the airplane with placards; replacing the gas spring; and replacing the hook assembly, retaining block, door guide blocks, and door sealant if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-09 · published Nov 9, 2026, effective Dec 14, 2026
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by reports that the low range radio altimeter (LRRA) system has an increased rate of non-computed data (NCD) outputs at low altitudes during approach and landing, which could cause unreliable altimeter function. This AD requires replacing the left and right LRRA transmit and receive coaxial cables with larger gauge coaxial cables. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-11 · published Nov 10, 2026, effective Dec 15, 2026
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 airplanes. This AD was prompted by a report of a missing main landing gear (MLG) brake rod center pin nut sub-assembly detected during an inspection. This AD requires, depending on airplane configuration, inspection of the MLG brake rod center pin nut, lock ring, and end plate, inspection of the MLG brake rod center pin and nut, and applicable corrective actions. This AD also requires additional work for certain airplanes. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-08 · published Nov 9, 2026, effective Dec 14, 2026
Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters (AH) Model EC130B4 helicopters. This AD was prompted by reports of weaknesses in the locking mechanisms on the left-hand side swinging and sliding door. This AD requires modifying the swing door star support and sliding door star support stringer. This AD also prohibits installing an affected composite door on any helicopter unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-10 · published Nov 9, 2026, effective Dec 14, 2026
Airbus Helicopters Deutschland GmbH (AHD) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2024-04-10 which applied to all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, and EC635T2+ helicopters. AD 2024-04-10 required repetitively inspecting certain part-numbered tail rotor (T/R) blades for a crack and, depending on the results, removing any cracked T/R blade from service. AD 2024-04-10 also prohibits installing certain T/R blades on any helicopter unless certain requirements are met. Since AD 2024-04-10 was issued, it was determined that inspection Method A should be discontinued and that additional limitations shall be provided. This AD retains the actions of AD 2024-04-10 and requires repetitively inspecting a certain tail rotor blade (TRB) assembly for cracks and, depending on the results, removing any cracked TRB assembly from service and replacing an affected part as terminating action for the repetitive inspections. This AD also prohibits installing an affected TRB assembly on any helicopter unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-12 · published Nov 12, 2026, effective Dec 17, 2026
Bell Textron Canada Limited Helicopters
The FAA is superseding Airworthiness Directive (AD) 2022-20- 11, which applied to certain Bell Textron Canada Limited Model 429 helicopters. AD 2022-20-11 required visually inspecting the external surface of the tail rotor (TR) gearbox support assembly, borescope inspecting or visually inspecting the inside of the tail boom, and performing a tactile inspection. Depending on the results of the inspections, AD 2022-20-11 required removing certain rivets from service or repairing gaps in accordance with an approved method. Since the FAA issued AD 2022-20-11, the manufacturer determined the repetitive inspection interval needs to be reduced. This AD requires the same actions as AD 2022-20-11 and reduces the inspection interval. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-03 · published Nov 2, 2026, effective Nov 23, 2026
BRP-Rotax GmbH & Co KG (Formerly BRP-Powertrain GMBH & CO KG and Bombardier-Rotax GmbH) Engines
The FAA is adopting a new airworthiness directive (AD) for all BRP-Rotax GmbH & Co KG (BRP-Rotax) Model 915 iSc2 C24, 915 iSc3 C24, 916 iSc2 A, 916 iSc2 C24, 916 iSc3 A, and 916 iSc3 C24 engines. This AD was prompted by a report of oil leakage from cracks in the wall of the turbocharger valve housing due to insufficient thickness. This AD requires replacement of the turbocharger valve housing and reidentification of the turbocharger. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-07 · published Nov 9, 2026, effective Dec 14, 2026
Rolls-Royce Deutschland Ltd & Co KG Engines
The FAA is adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Model BR700-725A1-12 engines. This AD was prompted by the manufacturer revising the airworthiness limitations section (ALS) of the existing time limits manual (TLM) to introduce new or more restrictive airworthiness limitations and associated thresholds and intervals for life-limited parts. This AD requires revising the ALS of the operator's existing approved engine maintenance or inspection program, as applicable, to incorporate new or more restrictive instructions and associated thresholds and intervals for life-limited parts. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2026-22-13 · published Nov 9, 2026, effective Nov 24, 2026
Lycoming Engines
The FAA is superseding Airworthiness Directive (AD) 2026-17- 10, which applied to Lycoming Engines (Lycoming) Model O-235, O-540, and IO-540 engines with a certain piston pin installed. AD 2026-17-10 required replacement of the affected piston pin with a part eligible for installation and, for certain engines, oil change and visual inspection of the engine oil filter, oil pressure screen, and oil suction screen for metal particulates. AD 2026-17-10 also prohibited the installation of an affected piston pin on any engine. Since the FAA issued AD 2026-17-10, the manufacturer has identified additional Lycoming Model engines that are subject to the unsafe condition, and the FAA determined the need to clarify the definition for an "affected piston pin," and include corrective action for engine models that were not listed in the manufacturer's service material. This AD requires replacement of the affected piston pin with a part eligible for installation and, for certain engines, oil change and visual inspection of the engine oil filter, oil pressure screen, and oil suction screen for metal particulates. This AD also prohibits the installation of an affected piston pin on any engine. This AD also expands the applicability to include additional affected engines with a certain piston pin installed. The FAA is issuing this AD to address the unsafe condition on these products.