Airworthiness Directive · Amendment 39-23512 · Tail rotor blades
Airbus Helicopters Deutschland GmbH (AHD) Helicopters
Quoted from the FAA's summary of this AD. The full text below is what applies.
This AD also prohibits installing an affected TRB assembly on any helicopter unless certain requirements are met.
Does it apply to your aircraft?
Enter an N-number to see every AD that names its model. Serial numbers and installed parts still decide.
This AD applies to all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, and EC635T2+ helicopters, certificated in any category.
The FAA is superseding Airworthiness Directive (AD) 2024-04-10 which applied to all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, and EC635T2+ helicopters. AD 2024-04-10 required repetitively inspecting certain part-numbered tail rotor (T/R) blades for a crack and, depending on the results, removing any cracked T/R blade from service. AD 2024-04-10 also prohibits installing certain T/R blades on any helicopter unless certain requirements are met. Since AD 2024-04-10 was issued, it was determined that inspection Method A should be discontinued and that additional limitations shall be provided. This AD retains the actions of AD 2024-04-10 and requires repetitively inspecting a certain tail rotor blade (TRB) assembly for cracks and, depending on the results, removing any cracked TRB assembly from service and replacing an affected part as terminating action for the repetitive inspections. This AD also prohibits installing an affected TRB assembly on any helicopter unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency AD 2026-0032, dated February 19, 2026 (EASA AD 2026-0032).
(1) Where EASA AD 2026-0032 refers to its effective date, this AD requires using the effective date of this AD.
(2) Where EASA AD 2026-0032 refers to January 29, 2024 (the effective date of EASA Emergency AD 2024-0028-E), this AD requires using March 19, 2024 (the effective date of AD 2024-04-10).
(3) Where EASA AD 2026-0032 refers to flight hours, this AD requires using hours time-in-service (TIS).
(4) Where paragraph (1) of EASA AD 2026-0032 specifies “Before an affected part exceeds 685 FH [flight hours] since first installation on a helicopter”, this AD requires replacing that text with “Before an affected part accumulates 685 hours TIS since first installation on a helicopter, or within 10 hours TIS after March 19, 2024 (the effective date of AD 2024-04-10), whichever occurs later”.
(5) Where paragraph 4.3 of the material referenced in EASA AD 2026-0032 recommends type II visible dye inspections, this AD requires the inspection methods in paragraphs (h)(5)(i), (ii), or (iii) of this AD, as applicable:
(i) If the affected part has previously been inspected using a type II visible dye method, perform type II visible dye (Method B of the material referenced in EASA AD 2026-0032) or eddy current inspections, instead of fluorescent penetrant inspections.
(ii) If the affected part has not previously been inspected using a type II visible dye inspection, perform eddy current or fluorescent penetrant inspections, instead of type II visible dye inspections.
(iii) If you cannot determine whether the affected part has previously been inspected by a type II visible dye method, clean all surfaces to be inspected and perform an eddy current or a fluorescent penetrant inspection, instead of a type II visible dye inspection.
Note 1 to paragraph (h)(5): The FAA reminds operators of the airworthiness concern regarding type II visible dye inspections of critical parts discussed in FAA Special Airworthiness Information Bulletin (SAIB) CE-18-26R1, dated October 30, 2018 (SAIB CE-18-26R1). SAIB CE-18-26R1 explains the risks associated with using type II visible dye inspection methods, including the prohibition in ASTM E1417 on the use of type II visible dye penetrant prior to the use of type I fluorescent penetrant on the same surface. SAIB CE-18-26R1 also advises of the importance of pre- and post-inspection cleaning to ensure proper detection of cracks. You can find SAIB CE-18-26R1 at drs.faa.gov.
Note 2 to paragraph (h)(5): The material referenced in EASA AD 2026-0032 identifies a type II visible dye inspection as Method A (not allowed) or Method B; eddy current inspection as Method C; fluorescent penetrant inspection as Method D; and visual inspection as Method E.
Note 3 to paragraph (h)(5): When entering compliance with the applicable paragraph of the AD into the helicopter maintenance records, documenting that a type II visible dye inspection was performed improves the accuracy of maintenance records.
(6) This AD does not adopt paragraph (3) of EASA AD 2026-0032.
(7) This AD does not adopt the “Remarks” section of EASA AD 2026-0032.
Where the material referenced in EASA AD 2026-0032 specifies to submit certain information and to send removed parts to the manufacturer, this AD does not include those actions.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.