48 Airworthiness Directives: 32 airplane, 3 rotorcraft, 10 engine, 1 propeller, 1 appliance, 1 glider.
AD 2018-19-26 · published Oct 1, 2018, effective Nov 5, 2018
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model MYSTERE-FALCON 200 airplanes. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-29 · published Oct 1, 2018, effective Nov 5, 2018
Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200 Freighter, -200, and -300 series airplanes; and Airbus SAS Model A340-200, -300, -500, and -600 series airplanes. This AD was prompted by a report of deficient fatigue performance of high strength steel used in forgings. Components made from the affected high strength steel are installed on the main landing gear (MLG), nose landing gear (NLG), and center landing gear (CLG). This AD requires identifying the part number and serial number of certain components installed on the MLG, NLG, and CLG; replacing affected parts; identifying the airplane's weight variant; and determining the applicable life limit for certain components installed on the MLG, NLG, and CLG. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-06 · published Oct 1, 2018, effective Nov 5, 2018
Airbus SAS Airplanes
We are superseding Airworthiness Directive (AD) 2016-25-03, which applied to certain Airbus Model A300 F4-600R series airplanes. AD 2016-25-03 required repetitive high frequency eddy current (HFEC) inspections of the aft lower deck cargo door (LDCD) frame forks; a one- time check of the LDCD clearances; and a one-time detailed visual inspection of hooks, eccentric bushes, and x-stops; and corrective actions if necessary. This AD requires repetitive HFEC inspections of the aft LDCD frame forks; a one-time check of the LDCD clearances; and a one-time detailed visual inspection of hooks, eccentric bushes, and x-stops; and corrective actions if necessary. This AD was prompted by a report of two adjacent frame forks that were found cracked on the aft LDCD of two airplanes during scheduled maintenance, and the introduction of frame fork reinforcement or repair procedures that, when done, allow an extension of repetitive inspection intervals. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-08 · published Oct 2, 2018, effective Oct 17, 2018
Airbus SAS Airplanes
We are superseding Airworthiness Directive (AD) 2018-02-18, which applied to certain Airbus SAS Model A318, A319, and A320 series airplanes and Model A321-111, -112, -131, -211, -212, -213, -231, and - 232 airplanes. AD 2018-02-18 required revising the airplane flight manual (AFM) to provide guidance to the flightcrew for certain emergency procedures. This new AD requires revising the AFM, and for certain airplanes, removing a certain AFM revision. This AD also adds airplanes to the applicability. This AD was prompted by a determination that, when two angle of attack (AoA) sensors are adversely affected by icing conditions at the same time, data displayed on the back up speed scale (BUSS) could be erroneous. This AD was also prompted by a determination that the AFM needs to be revised for certain additional airplanes, and that the AFM may have been erroneously revised on certain airplanes not equipped with a BUSS function. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-18 · published Oct 3, 2018, effective Nov 7, 2018
Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus SAS Model A300 B4-603, B4-620, and B4-622 airplanes; Model A300 B4-600R series airplanes; Model A300 C4-605R Variant F airplanes; and Model A300 F4-605R airplanes. This AD was prompted by reports of cracking on a certain frame (FR) angle fitting. This AD requires, depending on airplane configuration, a modification of certain angle fitting attachment holes; repetitive inspections for cracking of certain holes of the internal lower angle fitting web, certain holes of the internal lower angle fitting horizontal splicing, the aft bottom panel, and a certain junction area; and related investigative and corrective actions if necessary. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-23 · published Oct 3, 2018, effective Nov 7, 2018
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2013-01-02, which applied to certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes; and Model 757-200, 757- 200PF, and 757-300 series airplanes. AD 2013-01-02 required replacing the control switches of certain cargo doors. This AD requires replacement of certain cargo door control switches with a new, improved switch; installation of an arm switch in certain cargo doors; operational and functional tests; and applicable on-condition actions. This AD also adds airplanes to the applicability. This AD was prompted by reports of uncommanded cargo door operation. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-24 · published Oct 3, 2018, effective Nov 7, 2018
BAE Systems (Operations) Limited Airplanes
We are adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model 4101 airplanes. This AD was prompted by a determination that inspection requirements for a number of maintenance tasks are incorrect. This AD requires a one-time detailed inspection of a certain fuselage frame and repair, if necessary, and a revision of the maintenance or inspection program, as applicable, to incorporate new or revised maintenance instructions and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-07 · published Oct 3, 2018, effective Nov 7, 2018
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model MYSTERE-FALCON 50 airplanes. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new and more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-06 · published Oct 9, 2018, effective Nov 13, 2018
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 900EX airplanes. This AD was prompted by reports of rejected take-offs due to untimely inboard flap retraction. This AD requires modification of the slat/flap control wiring and replacement of the slat/flap control box with an improved box. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-07 · published Oct 9, 2018, effective Nov 13, 2018
Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 series airplanes; Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. This AD was prompted by a report of yellow hydraulic system failure, including both braking accumulators, due to failure of the parking brake operated valve (PBOV). This AD requires replacement of a certain PBOV with a different PBOV. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-27 · published Oct 9, 2018, effective Nov 13, 2018
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 2000EX airplanes. This AD was prompted by the manufacturer revising the airplane maintenance manual (AMM) maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-10 · published Oct 11, 2018, effective Nov 15, 2018
Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 airplanes. This AD was prompted by an inspection on the production line that revealed evidence of paint peeling on the forward and aft cargo frame forks around the hook bolt hole. This AD requires a detailed visual inspection for any deficiency of the frame forks around the hook bolt hole on certain forward and aft cargo doors and applicable corrective actions. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-24 · published Oct 15, 2018, effective Nov 19, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by significant changes made to the airworthiness limitations (AWL) related to fuel tank ignition prevention and the nitrogen generation system. This AD requires revision of the maintenance or inspection program, as applicable, to include the latest revision of the AWLs. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-03 · published Oct 15, 2018, effective Nov 19, 2018
Bombardier, Inc., Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports of multiple in-flight departures of the aft belly fairing access panels. This AD requires modification of the aft belly fairing access panels. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-05 · published Oct 15, 2018, effective Nov 19, 2018
Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-131, A319-132, A319-133, A320-231, A320-232, A320-233, A321-131, A321-231, and A321-232 airplanes. This AD was prompted by reports of fan cowl door (FCD) losses during take-off. This AD requires modification and re-identification, or replacement, of certain FCDs, and installation of a placard in the flight deck. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-07 · published Oct 15, 2018, effective Nov 19, 2018
Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus SAS Model A330-200 Freighter, -200, and -300 series airplanes. This AD was prompted by reports of Angle of Attack (AOA) blockages not detected by upgraded flight control primary computer (FCPC) software standards. This AD requires upgrading certain FCPCs, which terminates a certain airplane flight manual revision for certain airplanes. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-14 · published Oct 16, 2018, effective Nov 20, 2018
ATR-GIE Avions de Transport Régional Airplanes
We are adopting a new airworthiness directive (AD) for certain ATR-GIE Avions de Transport R[eacute]gional Model ATR42-500 airplanes. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new and/or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-15 · published Oct 16, 2018, effective Nov 20, 2018
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2015-09-07, which applied to all The Boeing Company Model 787 airplanes. AD 2015- 09-07 required a repetitive maintenance task for electrical power deactivation. This AD requires installing new software for the generator control unit (GCU). This AD also removes certain airplanes from the applicability. This AD was prompted by the determination that a Model 787 airplane that has been powered continuously for 248 days can lose all alternating current (AC) electrical power due to the GCUs simultaneously going into failsafe mode. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-17 · published Oct 16, 2018, effective Nov 20, 2018
Bombardier, Inc., Airplanes
We are superseding Airworthiness Directive (AD) 2012-22-10, which applied to certain Bombardier, Inc., Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL-600-2E25 (Regional Jet Series 1000) airplanes. AD 2012-22-10 required repetitive inspections to determine that cotter pins are installed at affected wing-to-fuselage attachment joints and replacement if necessary. This AD retains the initial inspection of the wing-to-fuselage attachment joints, and removes the repetitive inspections of all but the forward keel beam attachment joint. This AD also changes the repetitive inspection interval for the forward keel beam attachment joint. This AD was prompted by a determination that additional nuts of the forward keel beam attachment joint should be inspected, and that repetitive inspections of certain wing-to-fuselage attachment joints are not necessary. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-18 · published Oct 16, 2018, effective Nov 20, 2018
Bombardier, Inc., Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model DHC-8-400 series airplanes. This AD was prompted by a report of uncommanded deployment of the ground spoilers when the power levers were advanced for takeoff, which was caused by faulty switches in the power lever module. This AD requires revising the maintenance or inspection program, as applicable. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-19 · published Oct 16, 2018, effective Nov 20, 2018
Airbus SAS Airplanes
We are superseding Airworthiness Directive (AD) 2017-16-07, which applied to certain Airbus SAS Model A330-200, A330-200 Freighter, A330-300, A340-500, and A340-600 series airplanes; and Model A340-313 airplanes. AD 2017-16-07 required inspection of the fuselage bulk cargo door frames at specific locations, and corrective action if necessary. This AD requires new inspections of certain attachment holes for residual surface treatment and cracking, and corrective action if necessary; and provides an optional terminating action for the inspections. This AD also revises the applicability to add certain airplanes and remove others. This AD was prompted by a determination that only airplanes having certain manufacturer serial numbers (MSNs) are affected by tartaric sulfuric anodizing (TSA)/chromic acid anodizing (CAA) surface treatment in the door fitting attachment holes, and that airplanes having certain MSNs were excluded. This AD is intended to complete certain mandated programs intended to support the airplane reaching its limit of validity (LOV) of the engineering data that support the established structural maintenance program. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-20 · published Oct 16, 2018, effective Nov 20, 2018
Bombardier, Inc., Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by a report of cracking at the fastener holes of the left- hand-side support bracket of the elevator bell crank for the control linkage in the vertical stabilizer. This AD requires an eddy current inspection on certain support brackets of the elevator bell crank for any cracking at the fastener holes, a measurement to confirm that the fastener hole diameters are within tolerance, and replacement with a new support bracket of the elevator bell crank if necessary. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-21 · published Oct 16, 2018, effective Nov 20, 2018
Bombardier, Inc., Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-2B16 (CL-604 Variants) airplanes. This AD was prompted by reports of floodlight lamps found burned and the corresponding circuit breaker tripped as a result of fluid entering the cockpit floodlight fixtures. This AD requires installation of new gasket seals on floodlight fixtures. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-08 · published Oct 16, 2018, effective Nov 20, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, -500 series airplanes. This AD was prompted by the results of a fleet survey that revealed cracking in the bulkhead frame web at a certain body station. This AD requires repetitive inspections of the bulkhead frame web at a certain station, and applicable on-condition actions. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-09 · published Oct 16, 2018, effective Nov 20, 2018
ATR-GIE Avions de Transport Régional Airplanes
We are superseding Airworthiness Directive (AD) 2006-07-26, which applied to all ATR-GIE Avions de Transport R[eacute]gional Model ATR42 airplanes. AD 2006-07-26 required a one-time inspection to detect discrepancies (e.g., cracking, loose/sheared fasteners, distortion) on the left-hand and right-hand wings, of the outer wing box upper skin and upper rib feet, and repair if necessary. Since we issued AD 2006- 07-26, after initial findings had suggested the cracking was isolated to a few airplanes, we received reports of cracking in these same areas on other Model ATR42 airplanes. This AD requires repetitive inspections to detect discrepancies on the left-hand and right-hand wings, of the outer wing box upper skin and upper rib feet, and repair if necessary. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-13 · published Oct 17, 2018, effective Nov 15, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737 airplanes, excluding Model 737-100, -200, - 200C, -300, -400, and -500 series airplanes; all Model 757-200, -200PF, -200CB, and -300 series airplanes; and all Model 767-200, -300, -300F, and -400ER series airplanes. This AD was prompted by reports of latently failed motor-operated valve (MOV) actuators of the fuel shutoff valves. This AD requires replacing certain MOV actuators of the fuel shutoff valves for the left and right engines (on certain airplanes) and of the auxiliary power unit (APU) fuel shutoff valve (on Model 757 and Model 767 airplanes); and revising the maintenance or inspection program to incorporate certain airworthiness limitations (AWLs). We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-12 · published Oct 18, 2018, effective Nov 23, 2018
Bombardier, Inc., Airplanes
We are adopting a new airworthiness directive (AD) for certain
AD 2018-20-16 · published Oct 18, 2018, effective Nov 23, 2018
Bombardier, Inc., Airplanes
We are superseding Airworthiness Directive (AD) 2013-11-12,
AD 2018-21-13 · published Oct 23, 2018, effective Nov 27, 2018
Honda Aircraft Company LLC
We are superseding Airworthiness Directive (AD) 2018-11-05 for certain Honda Aircraft Company LLC (Honda) Model HA-420 airplanes. AD 2018-11-05 required incorporating a temporary revision into the airplane flight manual (AFM) and replacing the faulty power brake valve (PBV) upon condition. We issued AD 2018-11-05 as a short-term action to address the immediate need to detect and replace a faulty PBV. This AD retains the actions required in AD 2018-11-05 and requires replacing the faulty PBV with the improved part. We are issuing this AD to address the long-term corrective action and address the unsafe condition on these products.
AD 2018-21-02 · published Oct 24, 2018, effective Nov 28, 2018
Viking Air Limited Airplanes
We are adopting a new airworthiness directive (AD) for Viking Air Limited Model DHC-3 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as pitting corrosion on the shank of the wing strut attach bolts. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2018-22-03 · published Oct 24, 2018, effective Nov 28, 2018
Bombardier, Inc., Airplanes
We are superseding Airworthiness Directive (AD) 2016-24-03, which applied to certain Bombardier, Inc., Model DHC-8-400 series airplanes. AD 2016-24-03 required repetitive detailed inspections of barrel nuts and cradles, a check of the bolt torque of the preload indicating (PLI) washers, and corrective actions if necessary. This AD retains the requirements of AD 2016-24-03 and requires modifying the airplane by installing a sealing disk to a certain location and replacing certain barrel nuts. This AD was prompted by reports of cracked and corroded barrel nuts found at the mid-spar location of the horizontal-stabilizer-to-vertical-stabilizer attachment joint, and the issuance of new service information that includes a terminal modification. We are issuing this AD to address the unsafe condition on these products.
AD 2018-22-04 · published Oct 24, 2018, effective Nov 28, 2018
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2017-01-02, which applied to certain The Boeing Company Model 787-8 and 787-9 airplanes. AD 2017-01-02 required an inspection for discrepant inboard and outboard trailing edge flap rotary actuators, and replacing the rotary actuator or doing related investigative and corrective actions if necessary. This AD continues to retain those actions. This AD also adds airplanes to the applicability and reduces the number of affected actuators. This AD was prompted by a report indicating that some inboard and outboard trailing edge flap rotary actuators may have been assembled with an incorrect no-back brake rotor-stator stack sequence during manufacturing. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-09 · published Oct 3, 2018, effective Nov 7, 2018
Airbus Helicopters Deutschland GmbH Helicopters
We are adopting a new airworthiness directive (AD) for Airbus Helicopters Deutschland GmbH (Airbus Helicopters) Model MBB-BK 117 C-2 and MBB-BK 117 D-2 helicopters. This AD requires altering and re- identifying the overhead panel shock mount assembly (shock mount). This AD was prompted by the manufacturer's stress recalculations. The actions of this AD are intended to correct an unsafe condition on these products.
AD 2018-16-51 · published Oct 22, 2018, effective Nov 6, 2018
Bell Helicopter Textron Canada Limited Helicopters
We are publishing a new airworthiness directive (AD) for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. This AD was sent previously to all known U.S. owners and operators of these helicopters as Emergency AD 2018-16-51, dated July 26, 2018, which superseded Emergency AD 2018-15-51, dated July 20, 2018. This AD requires inspecting the tail rotor (T/R) gearbox installation, inspecting the T/R gearbox retaining hardware and support attachment point areas, and replacing each nut. This AD is prompted by two reports of T/R gearbox assemblies loosely attached to the gearbox support. The actions of this AD are intended to address an unsafe condition on these products.
AD 2018-21-15 · published Oct 23, 2018, effective Nov 27, 2018
Bell Helicopter Textron Canada Limited Helicopters
We are superseding Airworthiness Directive (AD) 2017-13-03 for Bell Helicopter Textron Canada Limited (Bell) Model 429 helicopters. AD 2017-13-03 required adding an identification number to life-limited rod ends that do not have a serial number (S/N). Since we issued AD 2017- 13-03, an additional life-limited rod end was identified that is affected by the same unsafe condition. This new AD retains the requirements of AD 2017-13-03 and revises the Applicability paragraph by adding that rod end. The actions of this AD are intended to address an unsafe condition on these products.
AD 2018-18-01 · published Oct 1, 2018, effective Oct 16, 2018
CFM International S.A. Turbofan Engines
The FAA is superseding Airworthiness Directive (AD) 2018-10-11 for all CFM International S.A. (CFM) Model CFM56-7B engines. AD 2018- 10-11 required initial and repetitive inspections of certain fan blades and, if they fail the inspection, their replacement with parts eligible for installation. This superseding AD requires the same initial and repetitive inspections but revises the compliance time for the repetitive inspections. This AD was prompted by further analysis by the manufacturer that indicated a need to reduce the repetitive fan blade inspection interval based on ongoing root cause investigation of an April 2018 engine failure. The agency is issuing this AD to address the unsafe condition on these products.
AD 2018-17-14 · published Oct 3, 2018, effective Nov 7, 2018
General Electric Company CF34-8E Engines
We are adopting a new airworthiness directive (AD) for certain General Electric Company (GE) CF34-8E turbofan engines. This AD was prompted by a report from GE regarding a quality escape of nonconforming thrust reverser fire seals. This AD requires a one-time inspection of the gap between the core cowl seal and the pylon seal of the thrust reverser for correct gap width, and replacement of the seals, if needed. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-16 · published Oct 10, 2018, effective Oct 25, 2018
CFM International S.A. Turbofan Engines
We are adopting a new airworthiness directive (AD) for all CFM International S.A. (CFM) LEAP-1A23, -1A24, -1A24E1, -1A26, -1A26E1, - 1A26CJ, -1A29, -1A29CJ, -1A30, -1A32, -1A33, -1A33B2, and -1A35A turbofan engines with certain full authority digital engine control (FADEC) and prognostic health monitoring (PHM) software installed. This AD requires removing certain FADEC and PHM software and installing versions eligible for installation. This AD was prompted by aborted takeoffs after engines did not advance to the desired takeoff fan speed due to icing in the pressure sensor line. We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-22 · published Oct 10, 2018, effective Oct 25, 2018
General Electric Company Turbofan Engines
We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) CF34-10A16, CF34-10E2A1, CF34-10E5, CF34- 10E5A1, CF34-10E6, CF34-10E6A1, CF34-10E7, and CF34-10E7-B turbofan engines with certain high-pressure turbine (HPT) front rotating air seals. This AD requires replacement of the affected HPT front rotating air seal. This AD was prompted by cracks found in the HPT front rotating air seal. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-01 · published Oct 15, 2018, effective Nov 19, 2018
Honeywell International Inc. Turbofan Engines
We are superseding Airworthiness Directive (AD) 2017-20-06 for certain Honeywell International Inc. (Honeywell) AS907-1-1A turbofan engines. AD 2017-20-06 required a one-time inspection of the second stage low-pressure turbine (LPT2) blades and, if the blades fail the inspection, the replacement of the blades with a part eligible for installation. This AD continues to require a one-time inspection of the LPT2 blades and, if the blades fail the inspection, the replacement of the blades with a part eligible for installation. This AD was prompted by the need to clarify the Applicability and Compliance sections of AD 2017-20-06. We are issuing this AD to address the unsafe condition on these products.
AD 2018-18-02 · published Oct 25, 2018, effective Nov 29, 2018
Austro Engine GmbH Engines
We are adopting a new airworthiness directive (AD) for certain Austro Engine GmbH model E4 engines and for all model E4P engines. This AD was prompted by reports of considerable wear on the timing chain on these engines. This AD requires replacement of the timing chain and amending certain airplane flight manuals to limit the use of windmill restarts. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-22 · published Oct 26, 2018, effective Nov 13, 2018
General Electric Company Turbofan Engines
We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) GE90-110B1, GE90-113B, and GE90-115B turbofan engines with a certain case combustor assembly (combustion case) installed. This AD requires removal of affected combustion cases from service and their replacement with a part eligible for installation. This AD was prompted by the discovery of a quality escape at a manufacturing facility involving unapproved welds on combustion cases. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-23 · published Oct 26, 2018, effective Nov 30, 2018
General Electric Company Turbofan Engines
We are superseding Airworthiness Directive (AD) 2017-07-04 for General Electric Company (GE) GE90-110B1 and GE90-115B turbofan engines with certain high-pressure compressor (HPC) rotor stage 2-5 spools installed. AD 2017-07-04 required removing certain HPC rotor stage 2-5 spools from service at times determined by a drawdown plan. This AD requires removing certain HPC rotor stage 2-5 spools from service before reaching the new reduced life limit and replacing them with parts eligible for installation. This AD was prompted by the publication of a GE service bulletin (SB) that increases the number of affected HPC rotor stage 2-5 spools and includes HPC rotor stage 2-5 spools that were inadvertently omitted from the applicability of AD 2017-07-04. We are issuing this AD to address the unsafe condition on these products.
AD 2018-22-06 · published Oct 29, 2018, effective Dec 3, 2018
Pratt & Whitney Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Pratt & Whitney (PW) PW2037, PW2037M, and PW2040 turbofan engines. This AD was prompted by an uncommanded high thrust event that occurred during approach on January 16, 2016, and during landing on April 6, 2016. This AD requires removal of the metering valve pilot valve (MVPV) within certain fuel control units (FCUs) and the MVPV's replacement with a part eligible for installation. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-11 · published Oct 31, 2018, effective Dec 5, 2018
Pratt & Whitney Division (PW) Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Pratt & Whitney Division (PW) PW4074D, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engines with a low-pressure compressor (LPC) fan hub, part number (P/N) 51B821 or P/N 52B521, installed. This AD was prompted by updated low-cycle fatigue analysis techniques that indicate certain LPC fan hubs could crack before their published life limit. This AD requires repetitive eddy current inspections (ECIs) and fluorescent penetrant inspections (FPIs) for cracks in certain LPC fan hubs and removal of LPC fan hubs from service that fail inspection. We are issuing this AD to address the unsafe condition on these products.
AD 2018-20-03 · published Oct 10, 2018, effective Nov 14, 2018
Hoffmann GmbH & Co. KG Propellers
We are adopting a new airworthiness directive (AD) for certain Hoffmann GmbH & Co. KG model HO-V 62 propellers. This AD was prompted by the failure of the propeller blade lag screws. This AD requires removal of the affected propeller blades and installation of modified propeller blades marked with change letter "A" or "B." We are issuing this AD to address the unsafe condition on these products.
AD 2018-19-15 · published Oct 10, 2018, effective Nov 14, 2018
GEVEN S.p.A. Seat Assemblies, Type D1-02 and D1-03
We are adopting a new airworthiness directive (AD) for certain GEVEN S.p.A. (Geven) Type D1-02 and D1-03 seat assemblies. This AD was prompted by a report that seat belt attachment bolts were found detached or partially detached from the seat. This AD requires inspection, torque verification, and modification of certain model seats. We are issuing this AD to address the unsafe condition on these products.
AD 2018-21-04 · published Oct 24, 2018, effective Nov 13, 2018
Glasgflugel Gliders
We are adopting a new airworthiness directive (AD) for Glasflugel Models Club Libelle 205, H 301 "Libelle," H 301B "Libelle," Kestrel, Mosquito, Standard "Libelle," and Standard Libelle-201B gliders. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as jamming between the double two-ring end of the towing cable and the deflector angles of the center of gravity (C.G.) release mechanism. We are issuing this AD to require actions to address the unsafe condition on these products.
