37 Airworthiness Directives: 32 airplane, 2 rotorcraft, 2 engine, 1 glider.
AD 2016-07-23 · published May 2, 2016, effective Jun 6, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of in-flight loss of fixed and hinged main landing gear (MLG) fairings, and reports of post-modification MLG fixed fairing assemblies that have wear and corrosion. This AD requires, for certain airplanes, repetitive replacements of the fixed fairing upper and lower attachment studs of both left-hand (LH) and the right-hand (RH) MLG; and repetitive inspections for corrosion, wear, fatigue cracking, and loose studs of each forward stud assembly of the fixed fairing door upper and lower forward attachment of both LH and RH MLG; and replacement if necessary. This AD also provides an optional terminating modification for the repetitive replacements of the fixed fairing upper and lower attachment studs. We are issuing this AD to prevent in-flight detachment of an MLG fixed fairing and consequent damage to the airplane.
AD 2016-08-15 · published May 2, 2016, effective Jun 6, 2016
Bombardier, Inc. Airplanes
We are superseding Airworthiness Directive (AD) 2014-17-51 for certain Bombardier, Inc. Model CL-600-2B16 airplanes. AD 2014-17-51 required inspecting the inboard flap fasteners of the hinge-box forward fitting at Wing Station (WS) 76.50 and WS 127.25 to determine the orientation and condition of the fasteners, as applicable, and replacement or repetitive inspections of the fasteners if necessary. AD 2014-17-51 also provided for optional terminating action for the requirements of that AD. This new AD requires accomplishment of the previously optional terminating action. This AD was prompted by a determination that that additional action is necessary. We are issuing this AD to detect and correct incorrectly oriented or fractured fasteners, that could result in premature failure of the fasteners attaching the inboard flap hinge-box forward fitting; failure of the fasteners could lead to the detachment of the flap hinge box and the flap surface, and consequent loss of control of the airplane.
AD 2016-08-19 · published May 2, 2016, effective Jun 6, 2016
Mitsubishi Heavy Industries, Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for certain Mitsubishi Heavy Industries, Ltd. Models MU-2B-30, MU-2B-35, MU-2B-36, MU-2B-36A, and MU-2B-60 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as reports of cracks found in the attach fittings of the main landing gear oleo strut. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2016-09-01 · published May 2, 2016, effective Jun 6, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes. This AD was prompted by reports of fatigue cracking of a certain chord of the pivot bulkhead. This AD requires repetitive inspections for cracking of the left side and right side forward outer chords of the pivot bulkhead, and related investigative and corrective actions if necessary. This AD also provides a modification of the pivot bulkhead, which would terminate the repetitive inspections. We are issuing this AD to detect and correct fatigue cracking of the outer flanges of the left and right side forward outer chords of the pivot bulkhead, which could result in a severed forward outer chord and consequent loss of horizontal stabilizer control.
AD 2016-09-03 · published May 2, 2016, effective Jun 6, 2016
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 2000, FALCON 2000EX, MYSTERE-FALCON 900, and FALCON 900EX airplanes. This AD was prompted by reports of a co- pilot sliding aft on his seat during take-off at rotation. This AD requires replacement of certain springs installed on the pilot and co- pilot seats. We are issuing this AD to prevent fatigue wear, which, if not corrected, could cause the seat to slide and the pilot or co-pilot to lose contact with the controls, leading to an inadvertent input on the flight control commands during take-off or climb, possibly resulting in loss of control of the airplane.
AD 2016-09-04 · published May 2, 2016, effective Jun 6, 2016
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by the discovery of a number of incorrectly calibrated angle of attack (AOA) transducers installed in the stall protection system. This AD requires replacement of incorrectly calibrated AOA transducers. We are issuing this AD to detect and replace incorrectly calibrated AOA transducers; incorrect calibration of the transducers could result in late activation of the stick pusher.
AD 2016-09-06 · published May 2, 2016, effective Jun 6, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes; Model A319-111, -112, -113, - 114, and -115 airplanes; Model A320-211, -212, and -214 airplanes; and Model A321-111, -112, -211, -212, and -213 airplanes. This AD was prompted by the results of an evaluation by the design approval holder (DAH). During a residual fatigue test, the forward engine mount failed prior to reaching the threshold/interval for the detailed inspections of the forward engine mounts specified in the airworthiness limitations. This AD requires repetitive detailed inspections of the right and left forward engine mounts, and corrective action if necessary. These inspections are required by AD 2015-05-02. This AD reduces the compliance times for those inspections. We are issuing this AD to detect and correct fatigue cracking in the forward engine mounts. Such cracking could result in reduced structural integrity of the airplane and could lead to in-flight loss of an engine, possibly resulting in reduced controllability of the airplane.
AD 2016-08-02 · published May 4, 2016, effective Jun 8, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A320-214, -232, and -233 airplanes; and Airbus Model A321- 211 and -231 airplanes. This AD was prompted by reports of incorrect installation of jiffy joint connectors on cables connected to certain passenger service units (PSUs), which could cause the passenger oxygen container to malfunction if the connector becomes disengaged during flight due to vibration. This AD requires identification of the affected PSUs, and depending on findings, doing applicable related investigative and corrective actions. We are issuing this AD to prevent failure of the door of the passenger oxygen container to open in the event of airplane decompression, resulting in lack of oxygen supply and consequent injury to occupants.
AD 2016-08-13 · published May 4, 2016, effective Jun 8, 2016
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 2004-19-11 for certain Airbus Model A320 series airplanes. AD 2004-19-11 required modification of the inner rear spar web of the wing, cold expansion of the attachment holes of the forward pintle fitting and the actuating cylinder anchorage of the main landing gear (MLG), repetitive ultrasonic inspections for cracking of the rear spar of the wing, and corrective action if necessary. AD 2004-19-11 also provided optional terminating action for the repetitive inspections. This new AD retains the requirements of AD 2004-19-11, and requires the previously optional terminating action. This AD was prompted by a determination that the previously optional terminating action is necessary to address the unsafe condition. We are issuing this AD to prevent fatigue cracking of the inner rear spar, which may lead to reduced structural integrity of the wing and the MLG.
AD 2016-09-05 · published May 4, 2016, effective Jun 8, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 717-200 airplanes. This AD was prompted by multiple reports of the vertical stabilizer leading edge showing signs of fastener distress. This AD requires a detailed inspection for any distress of the vertical stabilizer leading edge skin, and related investigative and corrective actions if necessary. This AD also requires, for certain airplanes, repetitive detailed inspections of the spar cap for any loose and missing fasteners, repetitive eddy current testing high frequency (ETHF) and radiographic testing (RT) inspections of the spar cap for any crack, and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct any crack in the vertical stabilizer leading edge and front spar cap, which may result in the structure becoming unable to support limit load, and may lead to the loss of the vertical stabilizer.
AD 2016-09-08 · published May 4, 2016, effective May 19, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-8 series airplanes. This AD requires a detailed inspection for correct installation of the flex hose clamp of the occupant backup air supply and a general visual inspection for damage of the flex hose, and related investigative and corrective actions if necessary. This AD was prompted by a report indicating that flex hoses of the occupant backup air supply were found disconnected from the adjacent fiberglass duct on two airplanes. We are issuing this AD to detect and correct an incorrect clamp installation on the inboard end of the flex hose, which allows the flex hose to slowly become disconnected from the adjacent fiberglass duct, and damage to the hose. This condition, in conjunction with a cargo fire event, can potentially lead to decreased airflow to the main deck, possibly resulting in smoke and/ or toxic fumes penetrating into the main deck passenger compartment, which could result in injury to the passengers or cabin crew.
AD 2016-09-07 · published May 6, 2016, effective Jun 10, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of airspeed indication discrepancies while flying at high altitudes in inclement weather. This AD requires replacing certain pitot probes on the captain, first officer, and standby sides with certain new pitot probes. We are issuing this AD to prevent airspeed indication discrepancies during inclement weather, which, depending on the prevailing altitude, could lead to unknown accumulation of ice crystals and consequent reduced controllability of the airplane.
AD 2016-09-10 · published May 6, 2016, effective Jun 10, 2016
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 2007-10-10 R1 for all Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). AD 2007-10-10 R1 required revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness to incorporate new limitations for fuel tank systems. This new AD requires revising the maintenance program or inspection program to incorporate revised fuel maintenance and inspection tasks. This AD was prompted by issuance of more restrictive maintenance requirements and/or airworthiness limitations by the manufacturer. We are issuing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors caused by latent failures, alterations, repairs, or maintenance actions, could result in fuel tank explosions and consequent loss of the airplane.
AD 2016-09-12 · published May 6, 2016, effective May 23, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 and 787-9 airplanes. This AD requires repetitive inspections of the bilge barriers located in the forward and aft cargo compartments for disengaged decompression panels, and reinstalling any disengaged panels. This AD was prompted by several reports of disengaged decompression panels found on in-service airplanes. We are issuing this AD to detect and correct disengaged decompression panels from the bilge barriers located in the forward and aft cargo compartments. In the event of a cargo compartment fire, this condition would provide a path for smoke and Halon to enter the flight compartment and passenger cabin, which could result in the inability to contain and extinguish a fire.
AD 2016-09-11 · published May 9, 2016, effective Jun 13, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200, -200 Freighter, and -300 series airplanes; and Model A340-200 and -300 series airplanes. This AD was prompted by reports that cracks were found on an adjacent hole of certain frames of the center wing box (CWB). This AD requires removing fasteners, doing a rototest inspection of fastener holes, installing new fasteners, oversizing the holes and doing rototest inspections for cracks if necessary, and repairing any cracking that is found. We are issuing this AD to detect and correct cracking on certain holes of certain frames of the CWB that could affect the structural integrity of the airplane.
AD 2016-09-13 · published May 9, 2016, effective Jun 13, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-300, -400, and -500 series airplanes. This AD was prompted by reports of fatigue cracking found at the left-side and right-side upper frames, at a certain area. This AD requires repetitive medium frequency eddy current (MFEC) inspections for cracking of the left-side and right-side upper frames, and repair (including open hole high frequency eddy current (HFEC) inspections for cracking of fastener holes) if necessary. This AD also provides an optional preventive modification, which terminates the repetitive inspections at the modified location. We are issuing this AD to detect and correct fatigue cracking of the upper frame, which can grow in size and result in a severed frame, leading to rapid decompression and consequent reduced structural integrity of the airplane.
AD 2016-10-01 · published May 11, 2016, effective Jun 15, 2016
M7 Aerospace LLC Airplanes
We are adopting a new airworthiness directive (AD) for all M7 Aerospace LLC Models SA226-AT, SA226-T, SA226-T(B), SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-CC, SA227-DC (C-26B), and SA227-TT airplanes. We received reports of failed elevator control rod ends due to corrosion and lack of lubrication. This AD requires initial and repetitive inspections and lubrication of the elevator control rod ends and bearings with replacement as necessary. We are issuing this AD to correct the unsafe condition on these products.
AD 2016-10-02 · published May 11, 2016, effective Jun 15, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes equipped with Rolls-Royce Trent 800 series engines. This AD was prompted by reports of heat damage to the strut aft fairing heat shield primary seal, as well as heat and wear damage to the heat shield insulation blankets. This AD requires repetitive inspections for cracks and heat damage to the strut aft fairing lower spar web structure (a flammable fluid zone barrier), for wear to the heat shield primary seal, and, as applicable, for heat and wear damage to heat shield insulation blankets; and related investigative and corrective actions if necessary. This AD also provides optional terminating action for the repetitive inspections. We are issuing this AD to detect and correct cracks and heat damage to the strut aft fairing lower spar web structure (a flammable fluid zone barrier), wear to the heat shield primary seal, and heat and wear damage to heat shield insulation blankets, which could lead to through-cracks in the aft fairing lower web structure and heating of the aft fairing lower web structure, and consequent uncontrolled fire in the aft fairing, fuel tank ignition or possible departure of the engine.
AD 2016-10-04 · published May 16, 2016, effective Jun 20, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by reports of cracked antenna support channels, skin cracking underneath the number 2 very high frequency (VHF) antenna, and cracking in the frames attached to the internal support structure. This AD requires repetitive inspections to determine the condition of the skin and the internal support structure, and follow-on actions including corrective action as necessary. We are issuing this AD to detect and correct skin cracking of the fuselage. Such cracking could result in separation of the number 2 VHF antenna from the airplane and rapid depressurization of the cabin.
AD 2016-10-05 · published May 16, 2016, effective Jun 20, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 757 airplanes. This AD was prompted by a report of cracking in the fuselage frame. This AD requires inspections for cracking in the fuselage frame, left and right sides, and repair if necessary. We are issuing this AD to detect and correct fuselage frame fatigue cracking. Such cracking could result in loss of structural integrity and the inability to sustain loading conditions.
AD 2016-10-06 · published May 19, 2016, effective Jun 23, 2016
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by a determination that the network interface installed between the Information Management System (IMS) 6000 unit and the Cabin Entertainment System (CES) network could affect the Aircraft Control Domain (ACD), and result in the transmission of misleading navigational information to the flightcrew. This AD requires inspecting the network interface installation between the IMS and the CES, and disconnecting the installation, if necessary. We are issuing this AD to prevent the transmission of misleading navigational information, which could adversely affect the ability of the flightcrew to maintain the safe flight and landing of the airplane.
AD 2016-10-07 · published May 19, 2016, effective Jun 23, 2016
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 airplanes. This AD was prompted by a report of a pilot commanding an in-flight engine shut down in response to a low oil pressure warning indication. Further investigation revealed the mounting studs in the engine mounted alternating current (AC) generator mounting plate were pulled out of position and the threaded interface in the plate was corroded. This AD requires repetitive inspections for discrepancies on certain AC generator mounting adapters, and replacing discrepant adapters with serviceable ones. This AD also requires revising the maintenance program to incorporate a repetitive task specified in certain temporary revisions. We are issuing this AD to detect and correct corrosion in the AC generator mounting plate, which could result in a gap between the AC generator and the generator mounting plate, and cause loss of engine oil and consequent engine failure.
AD 2016-10-10 · published May 19, 2016, effective Jun 23, 2016
Bombardier, Inc. Airplanes
We are superseding Airworthiness Directive (AD) 2014-20-01 for certain Bombardier, Inc. Model CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. AD 2014-20-01 required repetitive inspections for any fuel leak in the right-hand landing lights compartment, and related investigative and corrective actions if necessary. AD 2014-20-01 also provides for an optional replacement of the connector of the fuel boost pump canister of the auxiliary power unit (APU), which terminates the repetitive inspections. This new AD requires replacing the connector of the fuel boost pump canister of the APU. This AD was prompted by the determination that a terminating action for the repetitive inspections is necessary. We are issuing this AD to detect and correct fuel leaks in the right-hand landing lights compartment, which, in combination with the heat generated by the taxi lights and landing lights on the ground reaching the auto-ignition temperature of the fuel, could result in ignition of any fuel or fumes present in the right-hand landing lights compartment.
AD 2016-10-08 · published May 20, 2016, effective Jun 24, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200 Freighter, A330-200, A330-300, A340-200, A340- 300, A340-500, and A340-600 series airplanes. This AD was prompted by the results of endurance qualification tests on the trimmable horizontal stabilizer actuator (THSA), which revealed a partial loss of the no-back brake (NBB) efficiency in specific load conditions. This AD requires inspecting certain THSAs to determine the number of total flight cycles the THSA has accumulated, and replacing the THSA if necessary. We are issuing this AD to detect and correct premature wear of the carbon friction disks on the NBB of the THSA. Such a condition could lead to reduced braking efficiency in certain load conditions and, in conjunction with the inability of the power gear train to keep the ball screw in its last commanded position, could result in uncommanded movements of the trimmable horizontal stabilizer (THS) and loss of control of the airplane.
AD 2016-10-09 · published May 20, 2016, effective Jun 24, 2016
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 and 787-9 airplanes equipped with General Electric engines. This AD was prompted by reports of cracking in barrel nuts on a forward engine mount of Model 747-8 airplanes, which shares a similar design to the forward engine mount of Model 787- 8 and 787-9 airplanes. This AD requires, for certain airplanes, replacement of the four barrel nuts of the forward engine mount on each engine. For certain other airplanes, this AD requires an inspection to determine if any forward engine mount barrel nut having a certain part number is installed; and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct cracking of the forward engine mount barrel nuts. Such cracking could result in reduced load capacity of the forward engine mount and could result in separation of an engine from the airplane and consequent loss of control of the airplane.
AD 2016-10-16 · published May 23, 2016, effective Jun 27, 2016
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model MYSTERE-FALCON 900 airplanes, FALCON 900EX airplanes, and FALCON 2000EX airplanes. This AD was prompted by a report that during a test flight, it was found that the yaw damper on the takeoff roll can increase the Minimum Control Speed on Ground (Vmcg). This AD requires revising the airplane flight manual (AFM) to incorporate procedures for the flightcrew to check that the yaw damper is set to "off" before takeoff. We are issuing this AD to ensure that the flightcrew has procedures to set the yaw damper to "off" before takeoff, which, if activated, could result in reduced control of the airplane if one engine were to fail during takeoff.
AD 2016-10-11 · published May 26, 2016, effective Jun 30, 2016
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 2015-03-06 for all Airbus Model A330-200, A330-200 Freighter, A330-300, A340-200, A340-300, A340-500, and A340-600 series airplanes. AD 2015-03-06 required repetitive inspections of the left-hand (LH) and right-hand (RH) wing main landing gear (MLG) rib 6 aft bearing lugs (forward and aft) to detect any cracks on the two lugs, and replacement if necessary. This new AD requires reduction of certain compliance times. This AD was prompted by reports of additional cracking of the MLG rib 6 aft bearing lugs. We are issuing this AD to detect and correct cracking of the MLG rib 6 aft bearing lugs, which could result in collapse of the MLG upon landing.
AD 2016-10-12 · published May 26, 2016, effective Jun 30, 2016
Fokker Services B.V. Airplanes
We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by accomplishment of a taxi-out checklist which revealed that the elevator movement was partially obstructed due to rotation of the flight control lock adjuster bracket. This AD requires a one-time inspection of the elevator tension control regulator for discrepancies, and corrective actions if necessary. We are issuing this AD to detect and correct discrepancies of the elevator tension control regulators. Such a condition could result in jamming of the elevator mechanism and consequent reduced controllability of the airplane.
AD 2016-10-13 · published May 26, 2016, effective Jun 30, 2016
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300- 600 series airplanes); and Model A310 series airplanes. This AD was prompted by reports of premature aging of certain passenger chemical oxygen generators that resulted in the generators failing to activate. This AD requires an inspection to determine if certain passenger chemical oxygen generators are installed and replacement of affected passenger chemical oxygen generators. We are issuing this AD to prevent failure of the passenger chemical oxygen generator to activate and consequently not deliver oxygen during an emergency, possibly resulting in injury to airplane occupants.
AD 2016-10-14 · published May 26, 2016, effective Jun 30, 2016
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, and Model CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by a report indicating that some operators have inadvertently removed the existing insulation blankets from the upper wing box area. This AD requires inspecting for and replacing missing insulation blankets in the upper wing box area. We are issuing this AD to detect and replace missing insulation blankets from the upper wing box area, which could result in inadequate thermal protection to prevent fuel ignition in the event of an undetected bleed-air leak due to a cracked or ruptured bleed-air duct.
AD 2016-11-02 · published May 26, 2016, effective Jun 10, 2016
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for all Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes; Model CL-600-2D15 (Regional Jet Series 705) airplanes; Model CL-600-2D24 (Regional Jet Series 900) airplanes; and Model CL- 600-2E25 (Regional Jet Series 1000) airplanes. This AD requires a detailed visual inspection of the upper and lower engine pylons for protruding, loose, or missing fasteners; and repair, including applicable related investigative and corrective actions, if necessary. This AD was prompted by reports of loose or missing Hi-Lite fasteners on the upper and lower engine pylon structure common to the upper and lower pylon skin panels and engine thrust fitting. We are issuing this AD to detect and correct protruding, loose, or missing fasteners, which could result in structural failure of the engine pylons.
AD 2016-10-03 · published May 27, 2016, effective May 31, 2016
Viking Air Limited Airplanes
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. That AD applies to Viking Air Limited Model DHC-3 airplanes that are modified with the Baron Short Take Off and Landing (STOL) kit (Supplemental Type Certificate SA94-114 or SA 00287NY). The Code of Federal Regulations reference for records maintenance cited in last sentence in paragraph (f) is incorrect. This document corrects that error. In all other respects, the original document remains the same; however we are publishing the entire rule in the Federal Register.
AD 2016-08-20 · published May 2, 2016, effective Jun 6, 2016
Airbus Helicopters (Previously Eurocopter France)
We are superseding airworthiness directive (AD) 2014-12-51 for Airbus Helicopters (previously Eurocopter France) Model EC130B4 and EC130T2 helicopters. AD 2014-12-51 required repetitively inspecting the tailboom to Fenestron junction frame (junction frame) for a crack. This new AD retains the requirements of AD 2014-12-51, changes the applicability from helicopters with certain hours time-in-service (TIS) to junction frames with certain hours TIS, and adds a compliance time for sling cycles to the junction frame inspection interval. The actions of this AD are intended to detect a crack and to prevent failure of the junction frame, which could result in loss of the Fenestron and subsequent loss of control of the helicopter.
AD 2016-09-09 · published May 6, 2016, effective Jun 10, 2016
Airbus Helicopters (Type Certificate Previously Held by Eurocopter France)
We are superseding airworthiness directive (AD) 2013-08-17 for Airbus Helicopters Model SA-365N, SA-365N1, AS-365N2, AS 365 N3, and SA-366G1 helicopters. AD 2013-08-17 required initial and recurring inspections of the 9-degree fuselage frame for a crack and repairing the frame if a crack exists. This new AD modifies the compliance times and expands the inspection area of the 9-inch frame. The actions of this AD are intended to detect a crack in the 9-degree frame to prevent loss of structural integrity and subsequent loss of control of the helicopter.
AD 2016-09-02 · published May 4, 2016, effective Jun 8, 2016
Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Astazou XIV B and H turboshaft engines. This AD requires a one-time inspection of the front surface of the 3rd stage turbine for a groove. This AD was prompted by a report of a crack on the 3rd stage turbine wheel. We are issuing this AD to prevent cracks in the 3rd stage turbine wheel, failure of the engine, in-flight shutdown, and loss of control of the helicopter.
AD 2016-11-09 · published May 31, 2016, effective Jul 5, 2016
Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for Turbomeca S.A. Arriel 1D and 1D1 turboshaft engines with a pre- modification (mod) TU357 gas generator module (M03), installed. This AD requires removing the pre-modification (mod) TU357 gas generator module (M03) and replacing with a part eligible for installation. This AD was prompted by reports of divergent rubbing between the piston shaft small diameter labyrinth and the rear bearing support. We are issuing this AD to prevent failure of the labyrinth seal and engine, in-flight shutdown, and loss of control of the helicopter.
AD 2015-09-04 R1 · published May 2, 2016, effective Jun 6, 2016
DG Flugzeugbau GmbH Gliders
We are revising Airworthiness Directive (AD) 2015-09-04 for DG Flugzeugbau GmbH Model DG-1000T gliders equipped with a Solo Kleinmotoren Model 2350 C engine. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as engine shaft failure and consequent propeller detachment. We are issuing this AD to require actions to address the unsafe condition on these products.
