33 Airworthiness Directives: 27 airplane, 1 rotorcraft, 2 engine, 2 propeller, 1 various.
AD 2007-07-05 · published Apr 3, 2007, effective Apr 18, 2007
Boeing Model 777 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 777 airplanes. This AD requires a one-time inspection to determine the part number of the left and right air supply and cabin pressure controllers (ASCPCs) and installation of new ASCPC software if necessary. This AD results from a report of an ASCPC failure during flight. We are issuing this AD to prevent an ASCPC failure that could stop airflow into the airplane, inhibit the cabin altitude warning message, and cause an incorrect display of cabin altitude. These failures could result in depressurization of the airplane without warning.
AD 2007-07-06 · published Apr 3, 2007, effective Apr 9, 2007
Columbia Aircraft Manufacturing (Previously the Lancair Company) Models LC40-550FG, LC41-550FG, and LC42-550FG Airplanes
The FAA is adopting a new airworthiness directive (AD) for Columbia Aircraft Manufacturing (previously The Lancair Company) Models LC40-550FG, LC41-550FG, and LC42-550FG airplanes. This AD requires you to add information to the Limitations section of the Airplane Flight Manual (AFM). This AD also requires you to repetitively inspect the aileron and the elevator linear bearings and control rods for foreign object debris, scarring, or damage and take all necessary corrective actions. This AD results from reports of possible foreign object contamination of the linear bearings. We are issuing this AD to prevent jamming in the aileron and elevator control systems, which could result in failure. This failure could lead to loss of control.
AD 2007-07-09 · published Apr 3, 2007, effective May 8, 2007
Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A318-100, A319-100, A320- 200, A321-100, and A321-200 series airplanes; and Model A320-111 airplanes. That AD currently requires modification of the electrical bonding of all structures and systems installed inside the center fuel tank. This new AD requires modification of additional bonding points inside the center fuel tank. This AD results from a report that additional bonding points need to be modified in order to prevent electrical arcing in the center fuel tank. We are issuing this AD to prevent electrical arcing in the center fuel tank due to inadequate bonding, which could result in an explosion of the center fuel tank and consequent loss of the airplane.
AD 2007-07-10 · published Apr 3, 2007, effective May 8, 2007
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model ERJ 170 airplanes. This AD requires replacing the mini-latches on certain lavatory waste compartment doors with new, stronger latches, and other specified actions. This AD results from reports of certain lavatory waste compartment doors opening during flight due to movement of the waste compartment during takeoff, because the mini-latches installed on the doors of those compartments lose their strength over time. We are issuing this AD to prevent the inability of the waste compartment doors to adequately contain a fire inside the lavatory waste compartment, and consequent uncontained fire and smoke within a lavatory during flight.
AD 2007-07-11 · published Apr 3, 2007, effective Apr 18, 2007
Gulfstream Aerospace LP Model Gulfstream 200 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-07-08 · published Apr 5, 2007, effective May 10, 2007
Airbus Model A300 B2 and B4 Series Airplanes Equipped With General Electric CF6-50 Engines
The FAA is superseding an existing airworthiness directive (AD), which applies to Airbus Model A300 B2 and B4 series airplanes equipped with General Electric CF6-50 engines. That AD currently requires deactivating both thrust reversers and revising the airplane flight manual (AFM) to require performance penalties during certain takeoff conditions to ensure that safe and appropriate performance is achieved for airplanes on which both thrust reversers have been deactivated. This new AD requires one-time inspections of the directional pilot valve (DPV), the rocker arm and associated hardware, and corrective actions if necessary; reactivation of both thrust reversers; and repetitive inspections of the DPV and the associated control mechanism of the thrust reversers for incorrect assembly or excessive wear, and corrective actions if necessary. Accomplishing all of the actions would allow the removal of the AFM limitations in the existing AD. This AD results from reports indicating that the DPV was assembled incorrectly; further investigation revealed excessive wear on certain correctly assembled DPVs and the associated control mechanism. We are issuing this AD to prevent uncommanded in-flight deployment of a thrust reverser, which could result in reduced controllability of the airplane.
AD 2007-07-13 · published Apr 5, 2007, effective Apr 20, 2007
Gulfstream Aerospace LP Model Galaxy Airplanes and Model Gulfstream 200 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-07-14 · published Apr 5, 2007, effective May 10, 2007
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ airplanes. This AD requires modifying the forward and aft auxiliary fuel tanks. This AD results from a fuel system reassessment according to SFAR 88 criteria, which revealed the possibility of sparks due to chafing between the harnesses of the forward and aft auxiliary fuel tanks, between certain harnesses attached to the aircraft structure, or between certain harnesses attached to certain mechanical components. We are issuing this AD to prevent a potential ignition source inside a fuel tank, which, in combination with flammable fuel vapors, could result in a fuel tank explosion.
AD 2007-06-01 R1 · published Apr 6, 2007, effective Apr 16, 2007
Raytheon Aircraft Company Beech Models 45 (YT-34), A45 (T-34A, B-45), and D45 (T-34B) Airplanes
We are clarifying information contained in Airworthiness Directive (AD) 2007-06-01, which supersedes AD 62-24-01 and applies to all Raytheon Aircraft Company (RAC) Beech Models 45 (YT-34), A45 (T- 34A, B45), and D45 (T-34B) airplanes. AD 2007-06-01 currently requires you to repetitively inspect, using the eddy current method, the front and rear horizontal stabilizer spars for cracks and replace any cracked stabilizer. We inadvertently left out the language in this AD that required replacement of any horizontal stabilizer spar found cracked prior to further flight although the procedures in the appendix made reference to corrective action. The replacement information was contained in the notice of proposed rulemaking (NPRM). This document adds this information already proposed back into the AD. We are issuing this AD to prevent failure of the front and/or rear horizontal stabilizer spars caused by fatigue cracks. This failure could result in stabilizer separation and loss of control of the airplane.
AD 2007-07-15 · published Apr 9, 2007, effective May 14, 2007
Airbus Model A300 B4-601, A300 B4-603, A300 B4-605R, A300 C4-605R Variant F, A310-204, and A310-304 Airplanes Equipped With General Electric CF6-80C2 Engines
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A300 B4-600, B4-600R, C4- 605R Variant F, and F4-600R (collectively called A300-600) series airplanes; and Model A310 series airplanes. That AD currently requires a one-time inspection for damage of the integrated drive generator (IDG) electrical harness and pyramid arm, and repair if necessary. This new AD adds new repetitive inspections, which, when initiated, terminate the inspection required by the existing AD. This new AD also requires repairing damage and protecting the harness. This new AD also provides for optional terminating action for the repetitive inspections. This new AD also removes certain airplanes from the applicability of the existing AD. This AD results from a report of structural damage on the forward pyramid arm of an engine pylon due to chafing of the IDG electrical harness against the structure of the pyramid arm. We are issuing this AD to prevent electrical arcing in the engine pylon, which could result in loss of the relevant alternating current (AC) bus bar, reduced structural integrity of the engine pylon, and possible loss of control of the airplane.
AD 2007-08-03 · published Apr 12, 2007, effective May 2, 2007
Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-17-04, which applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. AD 2006-17-04 currently requires you to inspect the two end fittings on each of the flexible fuel hoses located in the engine compartment for the correct torque values, and, if any incorrect torque values are found during the inspection, tighten the hose end fittings to the correct torque values. This AD results from four reports of loose fuel lines connected to the fuel servo or fuel flow transducer. Two reports were of in-flight engine failure on a Model T182T airplane. A third report was of in-flight engine failure on a Model 206H airplane. A fourth report was of a Model 172S airplane losing engine power on final approach. Consequently, this AD would require you to establish the correct torque values of the end fittings on fuel hoses for certain Cessna Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD clarifies that the torque values need to be physically established and visual inspection only is not sufficient. We are issuing this AD to detect and correct potential loss of fuel flow, which may result in partial or complete loss of engine power and/or uncontrolled engine compartment fire due to fuel leakage forward of the firewall.
AD 2007-08-05 · published Apr 13, 2007, effective May 18, 2007
Airbus Model A330-200, A330-300, A340-200, and A340-300 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as fatigue damage with a crack propagation through the fastener line of the wing shroud box bottom panel, resulting in panel detachment and potential injuries to persons on the ground. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2007-08-06 · published Apr 13, 2007, effective May 18, 2007
British Aerospace Regional Aircraft Models HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-08-07 · published Apr 13, 2007, effective May 18, 2007
LATINOAMERICANA DE AVIACIÓN (LAVIA) S.A. (Type Certificate Data Sheets No. 2A8 and No. 2A10 Previously Held by The New Piper Aircraft, Inc.) Models PA-25, PA-25-235, and PA-25-260 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI references Latinoamericana de Aviaci[oacute]n S.A. Service Bulletin No. 25/53/03, dated May 10, 2006, which describes the unsafe condition as:
AD 2007-07-05 R1 · published Apr 18, 2007, effective Apr 18, 2007
Boeing Model 777 Airplanes
The FAA is revising an existing airworthiness directive (AD), which applies to all Boeing Model 777 airplanes. That AD currently requires a one-time inspection to determine the part number of the left and right air supply and cabin pressure controllers (ASCPCs), and installation of new ASCPC software if necessary. This AD requires those same actions. This AD also revises the existing AD to allow installation of an ASCPC with additional versions of software installed and to correct a part number reference. This AD results from a report of an ASCPC failure during flight. We are issuing this AD to prevent an ASCPC failure that could stop airflow into the airplane, inhibit the cabin altitude warning message, and cause an incorrect display of cabin altitude. These failures could result in depressurization of the airplane without warning.
AD 2007-08-08 · published Apr 20, 2007, effective May 25, 2007
Raytheon Aircraft Company (The Beech Aircraft Company and BEECH previously held Type Certificate Nos. 3A15, 3A16, 5A3, and A-777) Models 35-33, 35-A33, 35-B33, 35-C33, E33, F33, G33, 35-C33A, E33A, F33A, E33C, F33C, 35, A35, B35, C35, D35, E35, F35, G35, H35, J35, K35, M35, N35, P35, S35, V35, V35A, V35B, 36, A36, A45 (T-34A, B45), D45 (T-34B), 95-55, 95-A55, 95-B55, 95-B
We are adopting a new airworthiness directive (AD) that supersedes AD 72-22-01, which applies to certain Raytheon Aircraft Company (RAC) (The Beech Aircraft Company and BEECH previously held Type Certificate Nos. 3A15, 3A16, 5A3, and A-777) Models 33, 35, 36, 45, and 95 series airplanes. AD 72-22-01 currently requires you to determine if each uplock roller is of the greasible type (one having a drilled and grooved inner race), replace any nongreasible uplock roller (one having a solid inner race) with the greasible type before further flight, install hollow zerk-ended mounting bolts on the uplock rollers, and repetitively lubricate the uplock mechanism. Since we issued AD 72- 22-01, there was a recent incident involving a RAC Model 95-B55B (T- 42A) airplane where a seizure of the uplock rollers occurred. This malfunction of the uplock rollers is addressed in AD 72-22-01. Thus, the FAA has determined that the actions of AD 72-22-01 should also apply to certain serial numbers of the Model 95-B55B (T-42A) airplanes. Consequently, this AD retains all the actions of AD 72-22-01, adds those Model 95-B55B (T-42A) airplanes to the applicability of this AD, and lists the specific serial numbers. We are issuing this AD to decrease the possibility of gear-up landings caused by seizure of the uplock rollers.
AD 2007-09-01 · published Apr 20, 2007, effective Apr 25, 2007
Cessna Aircraft Company Models 182H, 182J, 182K, 182L, 182M, 182N, 182P, 182Q, and 182R Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 182 series airplanes that are equipped with Air Plains Services Corporation Supplemental Type Certificate (STC) SA00152WI. This AD requires you to disconnect or remove the electrical cable between the forward ground power relay and the starter relay, install a placard, inspect the fuel line between the auxiliary electric fuel pump and the engine-driven fuel pump for chafing, and replace the fuel line if chafing is found. This AD results from a report of an in-flight and post-landing engine compartment fire. We are issuing this AD to detect and correct interference between the ground power electrical cable, the fuel strainer cable, and the fuel line between the auxiliary electric fuel pump and the engine-driven fuel pump. This condition could lead to a fire in the engine compartment.
AD 2007-08-09 · published Apr 23, 2007, effective May 8, 2007
Short Brothers Model SD3-60 SHERPA, SD3-SHERPA, SD3-30, and SD3-60 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-09-02 · published Apr 26, 2007, effective May 31, 2007
REIMS AVIATION S.A. Model F406 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-09-03 · published Apr 26, 2007, effective May 11, 2007
Learjet Model 45 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Learjet Model 45 airplanes. This AD requires deactivating the auxiliary power unit (APU), capping/plugging the fuel lines to the APU, and removing the APU fuel shutoff valve. This AD results from reports of fuel leaking from the APU fuel shutoff valve into a flammable fluid fire protection area that is also interconnected with the main landing gear's wheel well bay. We are issuing this AD to prevent fuel leaking from the fuel shutoff valve of the APU, which could result in an uncontrollable fire and adversely affect the airplane's continued safe flight and landing.
AD 2007-06-52 · published Apr 30, 2007, effective May 7, 2007
Boeing Model 737-800 Series Airplanes
This document publishes in the Federal Register an amendment adopting airworthiness directive (AD) 2007-06-52 that was sent previously to all known U.S. owners and operators of Boeing Model 737- 800 series airplanes by individual notices. This AD requires inspecting spoilers to determine spoiler position after every landing and after any rejected takeoff maneuvers. For airplanes on which any spoiler is found in the up position with the speedbrake handle in the down position, this AD requires replacement of the flight spoiler actuator with a flight spoiler actuator having a certain part number. This AD also requires an operational test of the speedbrake control system after any maintenance actions that operate the spoiler system and replacement of the flight spoiler actuator if necessary. This AD also provides for optional terminating action for those requirements. In addition, this AD requires you to report to the manufacturer any spoiler panel that is found in the up position with the speedbrake handle in the down position. This AD results from a report of seven flight spoiler actuator jams on Model 737-800 Short Field Performance airplanes. We are issuing this AD to detect and correct any spoiler panel that is found in the up position with the speedbrake handle in the down position, which could result in a spoiler actuator hardover, and could cause the spoiler surface to jam in the fully extended position. Two or more hardover failures of the spoiler surfaces in the up direction on the same wing, if undetected prior to takeoff, can cause significant roll and consequent loss of control of the airplane.
AD 2007-06-53 · published Apr 30, 2007, effective May 7, 2007
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ 190 Airplanes
This document publishes in the Federal Register an amendment adopting airworthiness directive (AD) 2007-06-53 that was sent previously to all known U.S. owners and operators of EMBRAER Model ERJ 170 and ERJ 190 airplanes by individual notices. This AD requires repetitively verifying the correct closure of the forward and aft cargo doors, inspecting the forward and aft cargo doors for interference between the lock handle and the aft edge liner assembly, repetitively inspecting the lateral roller fittings on the forward and aft cargo door frames for damage, and doing corrective actions if needed. This AD also requires reporting any signs of interference or damage to the manufacturer. This AD results from a report indicating that the aft cargo door opened in flight just after departure, and from a report indicating that an airplane was dispatched with an unsecured forward cargo door. We are issuing this AD to prevent a cargo door from opening during flight, which could lead to structural failure or loss of control.
AD 2007-09-04 · published Apr 30, 2007, effective Jun 4, 2007
Boeing Model 777-200, 777-300, and 777-300ER Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 777-200, 777-300, and 777-300ER series airplanes. This AD requires repetitive inspections for discrepancies of the splined components that support the inboard end of the inboard trailing edge flap; related investigative, corrective, and other specified actions if necessary; a one-time modification of the inboard support of the inboard trailing edge flap by installing a new isolation strap and attachment hardware; and repetitive replacement of the torque tube assembly. For certain Boeing Model 777-200 series airplanes, this AD also specifies prior or concurrent accomplishment of one-time inspections of the flap seal panels for cracking and minimum clearances, and of the torque tubes for damage; and related investigative and corrective actions if necessary. This AD also provides a terminating action (modification of the inboard main flap) for the repetitive inspections. This AD results from reports of corrosion on the torque tube and closeout rib fittings that support the inboard end of the inboard trailing edge flap, as well as a structural reassessment of the torque tube joint that revealed the potential for premature fatigue cracking of the torque tube that would not be detected using reasonable inspection methods. We are issuing this AD to detect and correct corrosion or cracking of the torque tube and closeout rib fittings that support the inboard end of the inboard trailing edge flap. Cracking in these components could lead to a fracture, which could result in loss of the inboard trailing edge flap and consequent reduced controllability of the airplane.
AD 2007-09-05 · published Apr 30, 2007, effective Jun 4, 2007
APEX Aircraft Model CAP 10 B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-09-06 · published Apr 30, 2007, effective May 21, 2007
APEX Aircraft (Type Certificate No. A36EU Formerly Held by AVIONS MUDRY et CIE) Model CAP 10 B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as
AD 2007-09-07 · published Apr 30, 2007, effective Jun 4, 2007
EADS SOCATA Model TBM 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-09-08 · published Apr 30, 2007, effective Jun 4, 2007
Vulcanair S.p.A. Model P68 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-05-51 · published Apr 20, 2007, effective May 7, 2007
MD Helicopters Inc. (MDHI) Model MD600N Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2007-05-51, which was sent previously to all known U.S. owners and operators of MDHI Model MD600N helicopters by individual letters. This AD requires, before further flight, a visual and eddy current inspection of each lateral mixer output link assembly (mixer link) and replacing any cracked mixer link. This AD also requires performing an eddy current inspection on each mixer link before installing it on any helicopter. This amendment is prompted by the discovery of 3 cracked mixer links. The actions specified by this AD are intended to detect a crack in the mixer link, which could result in failure of the mixer link and subsequent loss of control of the helicopter.
AD 2007-07-07 · published Apr 6, 2007, effective Apr 23, 2007
General Electric Company CF34-1A, -3A, -3A1, -3A2, -3B, and -3B1 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for General Electric Company (GE) CF34-1A, -3A, -3A1, -3A2, -3B, and -3B1 turbofan engines. That AD requires a onetime inspection of certain fan disks for electrical arc-out indications, replacing fan disks with electrical arc-out indications, and reducing the life limit of certain fan disks. This AD requires the same reduced life limit of certain fan disks, but requires on-wing inspection of certain fan disks installed on regional jets within 500 flight hours after the effective date of this AD. This AD also requires more enhanced shop-level inspections of all fan disks for electrical arc-out defects. This AD results from a report that in January 2007, a CF34-3B1 turbofan engine experienced an uncontained fan disk failure during flight operation. We are issuing this AD to prevent an uncontained fan disk failure and airplane damage.
AD 2007-08-01 · published Apr 9, 2007, effective May 14, 2007
General Electric Company CT7-5, -7, and -9 Series Turboprop Engines
The FAA is superseding an existing airworthiness directive (AD) for General Electric Company (GE) CT7-5A2, -5A3, -7A, -7A1, -9B, - 9B1, and -9B2, -9C, -9C3, -9D, and -9D2 turboprop engines, with certain part number (P/N) and serial number stage 2 turbine aft cooling plates installed. That AD currently requires a onetime eddy current inspection (ECI) of boltholes in certain P/N stage 2 turbine aft cooling plates. This AD expands the population of affected CT7 turboprop engine models, but reduces the number of cooling plates affected. It also requires a onetime ECI of boltholes in certain P/N stage 2 turbine aft cooling plates with specific serial numbers. This AD results from the manufacturer expanding the list of affected engine models and identifying the affected stage 2 turbine aft cooling plates by serial number. We are issuing this AD to prevent separation of the stage 2 turbine aft cooling plate, resulting in uncontained engine failure and damage to the airplane.
AD 2007-08-02 · published Apr 12, 2007, effective Apr 27, 2007
Hartzell Propeller Inc. Model HC-E4A-3( )/E10950( ) Propellers
The FAA is adopting a new airworthiness directive (AD) for Hartzell Propeller Inc. model HC-E4A-3( )/E10950( ) propellers. This AD requires initial and repetitive inspections and rework of the propeller blade retention radius, and replacement of the propeller blade thrust bearing, for each blade. This AD results from reports of excessive propeller vibration and of damaged or broken propeller blade thrust bearings found during routine and investigative propeller disassembly. We are issuing this AD to prevent propeller blade separation, damage to the airplane, and possible loss of airplane control.
AD 2007-08-04 · published Apr 12, 2007, effective May 17, 2007
McCauley Propeller Systems Models 3A32C406/82NDB-X and D3A32C409/82NDB-X Propellers
The FAA is adopting a new airworthiness directive (AD) for McCauley Propeller Systems models 3A32C406/82NDB-X and D3A32C409/82NDB- X propellers, installed on Teledyne Continental Motors (TCM) IO-520, TSIO-520, or IO-550 reciprocating engines. These propellers are herein referred to as C406 and C409 propellers, respectively. This AD requires adding an operational revolutions per minute (RPM) restriction on the C406 and C409 propellers, and installing an RPM restriction placard in the cockpit. This AD also adds a 10,000-hour total time-in-service (TIS) life limit for these propellers. This AD also removes from service any propeller that has 10,000 hours or more total TIS, or that has an unknown total TIS. Also, this AD requires initial and repetitive propeller blade inspections for damage, and repair if necessary. This AD results from testing by the manufacturer that identified stress conditions that affect the fatigue life and damage tolerance of C406 and C409 propellers, when installed on TCM IO-520, TSIO-520, or IO-550 reciprocating engines. We are issuing this AD to prevent blade or hub failure that could result in separation of a propeller blade and loss of control of the airplane.
AD 2007-07-12 · published Apr 3, 2007, effective Apr 18, 2007
Honeywell Flight Management Systems (FMSs) Served by Honeywell NZ-2000 Navigation Computers Approved Under Technical Standard Order (TSO) TSO-C115a, and IC-800 Integrated Avionics Computers Approved Under TSOs C9c, C52a, and C115a; as Installed on Various Transport Category Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Honeywell FMSs served by Honeywell NZ-2000 navigation computers and IC- 800 integrated avionics computers. This AD requires identifying affected computers by part number and software modification level and revising the Limitations section of applicable airplane flight manuals to provide procedures for retaining optimum position determination and intended navigation. This AD results from reports of in-flight unannunciated shifts of computed position in airplanes with the subject flight management system (FMS) computers. We are issuing this AD to prevent a shift in the FMS computed position, which could result in uncommanded deviations from the intended flight path of the airplane and, if those deviations are undetected by the flight crew, compromised terrain/traffic avoidance.
