46 Airworthiness Directives: 36 airplane, 2 rotorcraft, 5 engine, 1 appliance, 2 glider.
AD 2007-05-02 · published Mar 1, 2007, effective Apr 5, 2007
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ 190 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all EMBRAER Model ERJ 170 and ERJ 190 airplanes. This AD requires repetitive detailed inspections for blockage of the pitot drain holes of certain air data smart probes (ADSPs), removing accumulated moisture from the pneumatic passages of the ADSPs, related investigative actions, and corrective actions if necessary. This AD results from reports of erroneous air speed indications caused by blockage of the pitot sensors due to freezing of accumulated moisture in the ADSP pneumatic passages. We are issuing this AD to prevent an erroneous air speed indication, which could reduce the flightcrew's ability to control the airplane.
AD 2007-05-03 · published Mar 5, 2007, effective Apr 9, 2007
Alpha Aviation Design Limited (Type Certificate No. A48EU Previously Held by APEX Aircraft and AVIONS PIERRE ROBIN) Model R2160 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-05-04 · published Mar 5, 2007, effective Apr 9, 2007
Mooney Airplane Company, Inc., (Mooney) Models M20M and M20R Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Mooney Airplane Company, Inc., Models M20M and M20R airplanes. This AD requires you to remove the upper left and upper right engine mount attaching hardware, cut out and remove the upholstery and insulation between the fuselage tubular frame and the firewall, and replace the upper left and upper right engine mount attaching hardware with the new parts kit. This AD results from failure of the engine mount attaching hardware to maintain torque as a result of firewall insulation and upholstery being compressed between the fuselage tubular frame and the firewall at the upper left and upper right engine mount attach points. We are issuing this AD to prevent the upper right and upper left engine mounting hardware from losing torque, which could result in a reduction in engine mount load carrying capability and could lead to engine mount failure.
AD 2007-05-05 · published Mar 5, 2007, effective Apr 9, 2007
SOCATA-Groupe AEROSPATIALE Models M.S. 760, M.S. 760 A, and M.S. 760 B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-05-06 · published Mar 5, 2007, effective Apr 9, 2007
McDonnell Douglas Model 717-200 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model 717-200 airplanes. This AD requires replacing certain attaching hardware of the bulkhead nipple assemblies of the left and right wing vent boxes with new electrical bonding attaching hardware, doing resistance testing of the new electrical bonds, and doing fuel leakage testing of the reworked nipple assemblies. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to provide a conductive path, from the bulkhead nipple assemblies of the left and right wing vent boxes to the airframe structure inside the wing fuel tanks, to dissipate high- amperage lightning-induced currents, which might otherwise create an ignition source for fuel vapors inside the wing vent boxes and lead to an explosion of the fuel tanks.
AD 2007-05-08 · published Mar 5, 2007, effective Apr 9, 2007
Airbus Model A330 and A340 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A330 and A340 airplanes. This AD requires revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness by incorporating new and revised certification maintenance requirements (CMRs). This AD results from the manufacturer's determination that additional and revised CMRs are necessary in order to ensure continued operational safety of the affected airplanes. We are issuing this AD to prevent safety- significant latent failures that would, in combination with one or more other specific failures or events, result in a hazardous or catastrophic failure condition.
AD 2007-05-11 · published Mar 5, 2007, effective Mar 20, 2007
Bombardier Inc. Airplanes
The FAA is superseding two existing airworthiness directives (ADs), that apply to certain Bombardier Model CL-600-2B16 (CL-604) airplanes and Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. These models may be referred to by their marketing designations as RJ100, RJ200, RJ440, CRJ100, CRJ200, CRJ440, and CL-65. One existing AD requires replacing the horizontal stabilizer trim control unit (HSTCU) with a new HSTCU. The other existing AD requires revising the airplane flight manual (AFM) to advise the flightcrew of procedures to follow in the event of stabilizer trim runaway, and in the event of MACH TRIM, STAB TRIM, and horizontal stabilizer trim malfunctions; and revising the AFM to require a review of the location of certain circuit breakers. That AD also requires doing a functional check of the stabilizer trim system and installing circuit breaker identification collars, and provides an optional terminating action. This new AD requires the previously optional terminating action and requires further revisions to the AFM. This AD also requires the removal of certain AFM revisions. This AD results from reports of trim problems including uncommanded trim, trim in the opposite direction to that selected, loss of trim position indication and, in one case, potential loss of trim disconnect capability. We are issuing this AD to prevent these events, which could result in conditions that vary from reduced controllability of the airplane to loss of control of the airplane.
AD 2007-05-07 · published Mar 6, 2007, effective Apr 10, 2007
Fokker Model F.28 Mark 0070 and 0100 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F.28 Mark 0070 and 0100 airplanes. This AD requires inspecting the carbon-fiber reinforced plastic main landing gear (MLG) door to determine whether certain part numbers are installed. For airplanes having certain doors, this AD requires inspecting the MLG outboard door for cracks, play, and loose sealant/bolts/nuts, and related investigative and corrective actions if necessary. This AD also requires, for airplanes having certain doors, modifying the rod bracket attachment of the MLG outboard door. This AD results from a report of a rod bracket of the MLG door detaching during flight. We are issuing this AD to detect and correct cracks in the rod bracket attachment bolts, which could result in the rod brackets detaching from the MLG door and blocking the proper functioning of the MLG.
AD 2007-05-09 · published Mar 7, 2007, effective Apr 11, 2007
REIMS AVIATION S.A. Model F406 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-05-10 · published Mar 7, 2007, effective Apr 11, 2007
Cessna Aircraft Company Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to install Modification Kit MK172-25-10C or a steel lock rod/bar on both crew seat back cylinder lock assemblies. If a steel lock rod/bar has already been installed on the crew seat back cylinder lock assembly, no further action is required. If you have already installed Modification Kit MK172-25-10A or MK172-25-10B, this AD requires you to do an installation inspection and correct any discrepancies found. This AD results from reports of the crew seat back cylinder lock assembly failing at the aft end and other cylinder lock assemblies found cracked. We are issuing this AD to prevent the crew seat back cylinder lock assembly from bending, cracking, or failing. This failure could cause uncontrolled movement of the seat back, resulting in possible backward collapse during flight. Backward collapse of either crew seat back could result in an abrupt pitch-up if the affected crew member continues to hold on to the control yoke during this failure and could cause difficulty in exiting the airplane from an aft passenger seat after landing.
AD 2007-05-12 · published Mar 7, 2007, effective Apr 11, 2007
Airbus Model A330 Airplanes and Model A340-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A330 airplanes and Model A340-200 and -300 series airplanes. This AD requires inspecting to determine the part number of certain S4- and MZ-type spoiler servo controls (SSCs). For certain other airplanes, this AD requires inspecting to determine the part number of all SSCs. This AD also requires replacing any affected SSC with a new SSC. This AD results from a new load duty cycle defined by the manufacturer. Additional fatigue tests and calculations done on this basis indicated that the spoiler valve manifold of the S4-type SSCs, and, on certain airplanes, the maintenance cover of the MZ-type SSCs, may crack during its service life due to pressure impulse fatigue. We are issuing this AD to prevent fatigue cracking of certain SSCs, which could result in hydraulic leakage and consequent loss of SSC function and loss of the associated hydraulic system. These conditions could affect all three hydraulic systems, which could result in reduced controllability of the airplane.
AD 2005-24-03 R1 · published Mar 8, 2007, effective Apr 12, 2007
Boeing Model 737-600, -700, -700C, and -800 Series Airplanes
The FAA is revising an existing airworthiness directive (AD) that applies to certain Boeing Model 737-600, -700, -700C, and -800 series airplanes. That AD currently requires inspecting/measuring the length of the attachment fasteners between the nacelle support fittings and the lower wing skin panels, and related investigative/corrective actions if necessary. That AD resulted from a report from the manufacturer that in production, during the installation of certain attachment fasteners for the nacelle support fittings, only one washer was installed instead of two. This new AD corrects errors found in the existing AD. We are issuing this AD to prevent inadequate fastener clamp-up, which could result in cracking of the fastener holes, cracking along the lower wing skin panels, fuel leaking from the wing fuel tanks onto the engines, and possible fire.
AD 2007-04-01 · published Mar 8, 2007, effective Mar 21, 2007
Pacific Aerospace Limited Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as possible installation of undersize rivets in the fuselage roof at STN 180.85, BL 19.67, WL 86.2. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2007-05-13 · published Mar 8, 2007, effective Apr 12, 2007
Airbus Model A319, A320, and A321 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A319, A320, and A321 airplanes. This AD requires installing spacer assemblies at the attachment points of the YZ-latches of the cargo loading system in the forward and aft cargo compartments, as applicable. This AD results from tests that have shown that the attachment points of the YZ-latches of the cargo loading system fail under maximum loads. We are issuing this AD to prevent failure of the attachment points of the YZ-latches, which could result in unrestrained cargo causing damage to the fire protection system, hydraulic system, electrical wiring, or other equipment located in the forward and aft cargo compartments. This damage could adversely affect the continued safe flight of the airplane.
AD 2007-05-18 · published Mar 8, 2007, effective Apr 12, 2007
EADS SOCATA Model TBM 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the finding of an improper geometry of some pulley brackets, which can offset the cable in the sheave. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2007-06-01 · published Mar 12, 2007, effective Apr 16, 2007
Raytheon Aircraft Company Beech Models 45 (YT-34), A45 (T-34A, B-45), and D45 (T-34B) Airplanes
We are adopting a new airworthiness directive (AD) that supersedes AD 62-24-01, which applies to all Raytheon Aircraft Company (RAC) Beech Models 45 (YT-34), A45 (T-34A, B45), and D45 (T-34B) airplanes. AD 62-24-01 currently requires you to repetitively inspect, using the dye penetrant method, the front and rear horizontal stabilizer spars for cracks and replace any cracked stabilizer. Since we issued AD 62-24-01, we determined that using the dye penetrant inspection method may not detect cracks before the crack grows to a critical length and causes failure of the horizontal stabilizer spars. Therefore, we are requiring the surface eddy current inspection method to detect cracks in the horizontal stabilizer spars. Consequently, this AD retains the actions required in AD 62-24-01 and changes the required inspection method from dye penetrant to surface eddy current. We are issuing this AD to prevent failure of the front and/or rear horizontal stabilizer spars caused by fatigue cracks. This failure could result in stabilizer separation and loss of control of the airplane.
AD 2007-06-02 · published Mar 15, 2007, effective Apr 19, 2007
Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Airbus Model A318-100 and A319-100 series airplanes, Model A320-111 airplanes, and Model A320-200, A321-100, and A321-200 series airplanes. That AD currently requires repetitive inspections of the upper and lower attachments of the trimmable horizontal stabilizer actuator (THSA) to measure for proper clearance and to detect cracks, damage, and metallic particles. The existing AD also requires corrective actions, if necessary, and reports of inspection findings. This new AD shortens the repetitive interval for inspecting the upper THSA attachment. This AD results from new test results on the secondary load path, which indicated the need to shorten the repetitive interval for inspecting the upper THSA attachment. We are issuing this AD to detect and correct failure of the THSA's primary load path, which could result in latent (undetected) loading and eventual failure of the THSA's secondary load path and consequent uncontrolled movement of the horizontal stabilizer and loss of control of the airplane.
AD 2007-06-03 · published Mar 15, 2007, effective Apr 19, 2007
Airbus Model A330 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as an incomplete discharge of the extinguishing agent in the fire zone, which could lead, in the worst case, in combination with an engine fire, to a temporary uncontrolled engine fire. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2007-06-04 · published Mar 15, 2007, effective Apr 19, 2007
EADS SOCATA Model TBM 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as two fatigue failures of flap carriage rollpins that occurred on in-service airplanes. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2007-06-05 · published Mar 15, 2007, effective Mar 30, 2007
Airbus Model A318, A319, A320 and A321 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-06-07 · published Mar 15, 2007, effective Apr 19, 2007
Raytheon Aircraft Company Models 58 and G58 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Raytheon Aircraft Company (RAC) Models 58 and G58 airplanes with optional propeller unfeathering accumulators installed. This AD requires you to inspect the left propeller accumulator oil tube assembly for any chafing; replace the propeller accumulator oil tube assembly if any chafing is found; and reposition and secure with clamps both the left engine manifold pressure hose and its metal identification tags to avoid contact with other tubes, hoses, electrical wires, parts, components, and structure. This AD results from several reports on the affected airplanes of chafing damage on the left propeller accumulator oil tube assembly. We are issuing this AD to detect, correct, and prevent any chafing damage of the left propeller accumulator oil tube assembly, which could result in loss of engine oil. Loss of engine oil may lead to fire or smoke in the engine compartment, inability to unfeather the propeller, engine damage, or loss of engine power.
AD 2007-06-09 · published Mar 15, 2007, effective Apr 19, 2007
Boeing Model 737-600, -700, -700C, and -800 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 737-600, -700, -700C, and - 800 series airplanes. That AD currently requires replacing the point "D" splice fitting between windows number 1 and 2 with a new splice fitting; performing an eddy current inspection for cracking of the holes in the structure common to the new splice fitting, including doing any related investigative actions; and performing corrective actions if necessary. This new AD adds repetitive inspections for cracking of the skin just below each splice fitting, and related corrective actions if necessary. This AD results from full-scale fuselage fatigue testing on the splice fitting that failed prior to the design objective on Boeing Model 737-800 series airplanes, and a report of a cracked splice fitting on an operational airplane. We are issuing this AD to prevent cracking of the existing fitting, which may result in cracking through the skin and consequent decompression of the flight deck.
AD 2007-06-06 · published Mar 16, 2007, effective Apr 20, 2007
B-N Group Ltd. BN-2, BN-2A, BN-2B, BN-2T, and BN-2T-4R Series (All Individual Models Included in Type Certificate Data Sheet (TCDS) A17EU, Revision 16, Dated December 9, 2002), and BN-2A-Mklll Trislander Series (All Individual Models Included in Type Certificate Data Sheet (TCDS) A29EU, Revision 4, Dated December 9, 2002) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-06-11 · published Mar 16, 2007, effective Apr 20, 2007
EADS SOCATA Model TBM 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-06-12 · published Mar 16, 2007, effective Apr 20, 2007
Airbus Model A330 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A330-300 airplanes. That AD currently requires reinforcement of the structure of the center fuselage by installing external stiffeners (butt straps) at frame (FR) 53.3 on the fuselage skin between left-hand (LH) and right-hand (RH) stringer (STR) 13, and related investigative and corrective actions. This new AD requires additional reinforcement of the structure of the center fuselage by installing external stiffeners (butt straps) at frame FR53.3 on the fuselage skin between LH and RH STR13, and related investigative and other specified actions. This AD also adds airplanes to the applicability. This AD results from cracking found at the circumferential joint of FR53.3. We are issuing this AD to prevent fatigue cracking of the fuselage, which could result in reduced structural integrity of the fuselage.
AD 2007-06-13 · published Mar 16, 2007, effective Apr 20, 2007
Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes); and Model A310 Airplanes; Equipped With General Electric CF6-80A3 or CF6-80C2 Engines
The FAA is adopting a new airworthiness directive (AD) for certain Airbus airplane models, as specified above. This AD requires installing electro-pneumatic locking bar devices (TRAS lock systems) in the engine nacelles, installing a dedicated and shielded electrical circuit that is segregated from the existing thrust reverser control system, and performing related investigative/corrective actions if necessary. This AD results from the manufacturer's reassessment of the thrust reverser systems in the Airbus airplane models specified above, which showed that the thrust reverser could inadvertently deploy in flight under certain conditions. We are issuing this AD to prevent inadvertent deployment of thrust reversers in flight, which could result in reduced controllability of the airplane.
AD 2007-06-14 · published Mar 16, 2007, effective Apr 20, 2007
EADS SOCATA Model TBM 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the discovery of propeller control cables with a defective crimping. Two cable ends were found uncrimped at the factory after an engine run-up test, and one cable end was also found uncrimped on the first 100-hour aircraft maintenance check. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2007-06-16 · published Mar 20, 2007, effective Apr 24, 2007
Alpha Aviation Design Limited (Type Certificate No. A48EU Previously Held by APEX Aircraft and AVIONS PIERRE ROBIN) Model R2160 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI references Alpha Aviation Service Bulletin AA-SB-28-002, dated June 28, 2006, which describes the unsafe condition as:
AD 2007-06-17 · published Mar 23, 2007, effective Apr 27, 2007
Airbus Model A320 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A320 series airplanes. This AD requires replacing the carbon fiber reinforced plastic (CFRP) actuator fittings of the rudder with aluminum actuator fittings and doing related investigative and corrective actions. This AD results from rupture of a CFRP actuator fitting during maintenance. We are issuing this AD to prevent rupture of a rudder actuator fitting, which could result in reduced controllability of the airplane.
AD 2007-06-18 · published Mar 23, 2007, effective Apr 27, 2007
Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 airplanes. This AD requires repetitive inspections of the operation of the main landing gear (MLG) door opening sequence to determine if a defective actuator is installed, and replacing any defective actuator with a new actuator. This AD results from reports of slow operation of the MLG door opening/ closing sequence due to a defective actuator. We are issuing this AD to detect and correct defective actuators of the MLG door, which could result in slow operation of the MLG door and consequent non-extension of the MLG during an emergency freefall operation.
AD 2007-06-19 · published Mar 23, 2007, effective Apr 27, 2007
Bombardier Model DHC-8-102, -103, and -106 Airplanes and Model DHC-8-200 and DHC-8-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-102, -103, and -106 airplanes and Model DHC-8-200 and DHC-8-300 series airplanes. This AD requires modifying the main landing gear (MLG) and nose landing gear (NLG) handle assemblies for alternate release and the MLG retaining plate. This AD also requires doing a related investigative action and corrective action if necessary. This AD results from reports of broken or damaged MLG and NLG alternate release cables caused by rubbing and fraying at the cable-to-handle interface. We are issuing this AD to prevent breakage of the MLG and NLG alternate release cables, which, if the normal gear extension fails, could result in the inability to extend the MLG or NLG and consequent collapse of the landing gear during ground maneuvers or upon landing.
AD 2007-07-01 · published Mar 28, 2007, effective May 2, 2007
Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A300-600 airplanes. This AD requires an inspection to determine if certain spoiler actuators having certain part numbers are installed, and eventual replacement of all affected actuators. This AD results from failure of a distribution block, which was detected during fatigue qualification tests of certain spoiler actuators. We are issuing this AD to prevent failure of the distribution block, which could result in leakage of the hydraulic fluid that supplies those actuators. This failure could cause failure of one of the three spoiler actuators and the associated hydraulic circuits, which could result in loss of those hydraulic circuits and consequent reduced controllability of the airplane.
AD 2007-07-02 · published Mar 28, 2007, effective May 2, 2007
Boeing Model 737-300, -400, -500, -600, -700, -800 and -900 Series Airplanes; and Model 757-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-300, -400, -500, -600, -700, -800 and -900 series airplanes; and Model 757-200 and -300 series airplanes. This AD requires modifying the activation mechanism in the chemical oxygen generator of each passenger service unit (PSU). This AD results from several reports indicating that some chemical oxygen generators failed to activate during in-flight decompression events. These failures were due to fracture of components between the passenger oxygen mask and the release pin in the oxygen generator. We are issuing this AD to prevent failure of the activation mechanism in the chemical oxygen generator, which could result in the unavailability of supplemental oxygen and possible incapacitation of passengers and cabin crew during an in- flight decompression.
AD 2007-07-03 · published Mar 28, 2007, effective May 2, 2007
Boeing Model 747 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747 airplanes. This AD requires repetitive tests to detect hot air leaking from the trim air diffuser ducts or sidewall riser duct assemblies (collectively referred to in this AD as "TADDs"), related investigative actions, and corrective actions if necessary. This AD also provides an optional terminating action for the repetitive tests. This AD results from reports of sealant deteriorating on the outside of the center wing fuel tank and analysis that sealant may deteriorate inside the tank due to excess heat from leaking TADDs. We are issuing this AD to prevent leakage of fuel or fuel vapors into areas where ignition sources may be present, which could result in a fire or explosion.
AD 2007-07-04 · published Mar 28, 2007, effective May 2, 2007
McDonnell Douglas Model MD-11 and -11F Airplanes
The FAA is adopting a new airworthiness directive (AD) for all McDonnell Douglas Model MD-11 and -11F airplanes. This AD requires revising the maintenance inspection program that provides for inspection of principal structural elements (PSEs) and replacement of safe-life parts, to incorporate a new revision to the MD-11 Airworthiness Limitations Instructions. The revision reduces inspection intervals for fatigue cracking of certain PSEs, and expands the inspection area for a certain other PSE. This AD results from a revised damage tolerance analysis. We are issuing this AD to detect and correct fatigue cracking of certain PSEs, which could adversely affect the structural integrity of the airplane.
AD 2007-06-15 · published Mar 19, 2007, effective Apr 23, 2007
Eurocopter France Model AS350B, AS350B1, AS350B2, AS350B3, AS350BA, AS350C, AS350D, and AS350D1 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Eurocopter France (Eurocopter) model helicopters that requires replacing a certain hydraulic drive belt (drive belt). Also required is reducing the lubrication time interval for a certain hydraulic pump drive shaft (drive shaft). This amendment is prompted by in-flight failures of the drive belt and the drive shaft. The actions specified by this AD are intended to prevent in-flight failure of the drive belt or drive shaft, loss of hydraulic power to the flight control system, and subsequent loss of control of the helicopter.
AD 2006-26-51 · published Mar 23, 2007, effective Apr 9, 2007
Eurocopter Deutschland GmbH Model MBB-BK 117 C-2 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2006-26-51, which was sent previously to all known U.S. owners and operators of Eurocopter Deutschland GmbH (ECD) Model MBB-BK 117 C-2 helicopters by individual letters. This AD requires, before further flight, marking the position of the tail rotor control lever dynamic weights (weights), removing the split pins and the weights, and visually inspecting and replacing, if necessary, the tail rotor control lever before further flight. This AD also requires, within 10 hours time-in-service (TIS), and thereafter at intervals not to exceed 25 hours TIS, repeating the visual inspection of the tail rotor control lever and replacing any unairworthy tail rotor control lever with an airworthy tail rotor control lever before further flight. Also required is reassembling the tail rotor control lever by following the appropriate maintenance instruction. This amendment is prompted by an in-flight incident in which the threaded portion of the tail rotor control lever containing a dynamic weight broke off leading to severe vibrations. The actions specified by this AD are intended to prevent separation of the weights in flight, severe vibration, and subsequent loss of control of the helicopter.
AD 2007-05-14 · published Mar 5, 2007, effective Apr 9, 2007
General Electric Company (GE) CF6-80C2 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for GE CF6-80C2 series turbofan engines. This AD requires replacing certain installed part number (P/N) and serial number (SN) cast titanium weld- repaired forward engine mount platforms and cast titanium forward mount yokes, with a forged titanium or a non-welded cast titanium part. This AD results from the discovery of cracks, in a weld-repaired area on a forward engine mount platform and a forward engine mount yoke, found during a fluorescent penetrant inspection (FPI). These parts were weld- repaired during manufacture. We are issuing this AD to prevent cracks in the forward engine mount platform and forward engine mount yoke that could result in possible separation of the engine from the airplane.
AD 2007-05-16 · published Mar 7, 2007, effective Mar 12, 2007
General Electric Aircraft Engines (GE) CF34-3A1/-3B/-3B1 Turbofan Engines
This action supersedes emergency airworthiness directive (AD) 2007-04-51 that was sent previously to all known U.S. owners and operators of GE CF34-3A1/-3B/-3B1 turbofan engines. That action required a onetime visual and tactile inspection of certain areas of certain serial number (SN) fan disks for an arc-out defect, within 20 engine flight hours after the effective date of that AD. This AD supersedes AD 2007-04-51 and adds eight SNs to the list of suspect fan disks. This AD results from GE discovering eight additional SNs of fan disks suspected of having an arc-out defect, and from the original report that a GE CF34-3B1 turbofan engine experienced an uncontained fan disk failure during flight operation. We are issuing this AD to prevent an uncontained fan disk failure and airplane damage.
AD 2007-05-17 · published Mar 8, 2007, effective Apr 12, 2007
Pratt & Whitney JT9D Series Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT9D series turbofan engines. That AD currently requires revisions to the Airworthiness Limitations Section (ALS) of the manufacturer's Instructions for Continued Airworthiness (ICA) to include required enhanced inspection of selected critical life-limited parts at each piece-part opportunity. This AD modifies the JT9D series engines ALS sections of the manufacturer's manuals and an air carrier's approved continuous airworthiness maintenance program to incorporate additional inspection requirements. This AD results from the need to require enhanced inspection of selected critical life- limited parts of JT9D series turbofan engines. We are issuing this AD to prevent critical life-limited rotating engine part failure, which could result in an uncontained engine failure and damage to the airplane.
AD 2007-05-15 · published Mar 12, 2007, effective Apr 16, 2007
Teledyne Continental Motors GTSIO-520 Series Reciprocating Engines
The FAA is superseding an existing airworthiness directive (AD) for Teledyne Continental Motors (TCM) GTSIO-520 series reciprocating engines. That AD currently requires initial and repetitive visual inspections of the starter adapter assembly and crankshaft gear and unscheduled visual inspections of the starter adapter assembly and crankshaft gear due to a rough-running engine. That AD also requires replacement of the starter adapter shaft gear needle bearing with a certain bushing and installation of a certain TCM service kit at the next engine overhaul, or at the next starter adapter replacement, whichever occurs first. This AD requires performing the inspection ordered in paragraph (h) of this AD every 100 hours time-in- service (TIS), or annually. This proposed AD results from an error discovered in AD 2005-20-04. We are issuing this AD to failure of the starter adapter assembly and or crankshaft gear, resulting in failure of the engine and possible forced landing.
AD 2007-06-10 · published Mar 15, 2007, effective Apr 19, 2007
Rolls-Royce plc RB211-524 Series Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Rolls Royce plc (RR) RB211-524 series turbofan engines with certain part number (P/N) intermediate pressure compressor (IPC) stage 5 disks installed. That AD currently requires new reduced IPC stage 5 disk cyclic limits. This AD requires the same reduced IPC stage 5 disk cyclic limits, requires removal from service of affected disks that already exceed the new reduced cyclic limit, and, removal from service of other affected disks before exceeding their cyclic limits using a drawdown schedule. This AD also exempts disks reworked to RR Service Bulletin (SB) No. RB.211-72-E182, Revision 1, dated July 30, 2004, and allows an on-wing eddy current inspection (ECI) on RB211-524G and RB211-524H series engines. This AD results from the manufacturer issuing a revised Alert Service Bulletin (ASB) to remove certain disks from applicability, and to allow an on-wing ECI on RB211-524G and RB211-524H series engines. We are issuing this AD to prevent failure of the IPC stage 5 disk, which could result in uncontained engine failure and possible damage to the airplane.
AD 2007-05-20 · published Mar 12, 2007, effective Apr 16, 2007
Microturbo Saphir 20 Models 095 Auxiliary Power Units (APU)
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-05-19 · published Mar 8, 2007, effective Apr 12, 2007
Glasflugel Models H 301 “Libelle,” H 301B “Libelle,” Standard “Libelle,” and Standard Libelle-201B Sailplanes
The FAA adopts a new airworthiness directive (AD) for all Glasflugel Models H 301 "Libelle," H 301B "Libelle," Standard "Libelle," and Standard Libelle-201B sailplanes. This AD requires you to replace the rudder actuator arm (manufactured according to drawing No. 301-45-10) with an improved design rudder actuator arm (manufactured following drawing No. 301-45-13). This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to detect and correct damage to the rudder actuator arm, which could result in failure of the rudder actuator arm. This failure could result in reduced or loss of rudder control.
AD 2007-06-08 · published Mar 15, 2007, effective Apr 19, 2007
Przedsiebiorstwo Doswiadczalno-Produkcyjne Szybownictwa “PZL-Bielsko” Model SZD-50-3 “Puchacz” Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
