28 Airworthiness Directives: 22 airplane, 4 rotorcraft, 2 engine.
AD 2025-08-05 · published May 1, 2025, effective Jun 5, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes. This AD was prompted by a widespread fatigue damage (WFD) scenario review for a certification project that indicated several cracks found around the potable water and wastewater service panels were WFD instead of typical fatigue. This AD requires modification of the potable water and wastewater service panels, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-05 · published May 1, 2025, effective Jun 5, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A318 series airplanes, Model A319-111, -112, - 113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes; and Model A321-111, -112, - 131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by cracks being found during full-scale fatigue testing of the keel beam bottom panel between the edge profile and stringer run-out at a certain frame and stringer. This AD requires repetitive special detailed inspections (SDI) of the affected area, and corrective actions, if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-04 · published May 2, 2025, effective Jun 6, 2025
Bombardier Inc. Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-08 · published May 5, 2025, effective May 5, 2025
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 747 airplanes. This AD was prompted by a report that a right-hand outboard elevator was received and installed without balance weights. This AD requires doing a maintenance records check to determine if certain outboard elevators are installed or an inspection to determine if outboard elevators have balance weights, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-07-01 · published May 6, 2025, effective May 15, 2025
Thommen Aircraft Equipment AG Digital Air Data Computers
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. The AD applies to certain Thommen Aircraft Equipment AG (THOMMEN) AC32 Digital Air Data Computers (ADCs). As published, there were typographical errors in the some of the aircraft models in the applicability table. This document corrects those errors. In all other respects, the original document remains the same.
AD 2025-09-11 · published May 8, 2025, effective Jun 12, 2025
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD- 83), DC 9-87 (MD-87), and MD-88 airplanes, and Model DC-9-10, DC-9-20, DC-9-30, DC-9-40, and DC-9-50 series airplanes. This AD was prompted by the discovery of jammed elevators during takeoff. This AD requires revising the "Certificate Limitations" section of the existing airplane flight manual (AFM) to include a procedure to confirm elevator surfaces are not jammed in the trailing edge down (TED) position. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-02 · published May 14, 2025, effective Jun 18, 2025
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2022-19- 09, which applied to all Airbus Canada Limited Partnership Model BD- 500-1A10 and BD-500-1A11 airplanes. AD 2022-19-09 required repetitive inspections of the left and right main landing gear (MLG) lower spindle pins to detect corrosion and applicable repair or replacement. This AD was prompted by reports of in-service findings of corrosion on the flange of the MLG lower spindle pin. This AD continues to require certain actions in AD 2022-19-09. This AD also requires changing the tracking of flight cycles for inspections from the usage of the MLG to the usage of MLG lower spindle assemblies and replacement of affected MLG lower spindle assemblies, removes airplanes from the applicability, and prohibits the installation of affected parts under certain conditions; as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-09 · published May 14, 2025, effective Jun 18, 2025
MHI RJ Aviation ULC (Type Certificate Previously Held by Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all MHI RJ Aviation ULC Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2C11 (Regional Jet Series 550), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by reports that the cockpit voice recorder (CVR) impact switch was installed in the wrong direction. This AD requires an inspection of the CVR impact switch installation to confirm that the reset switch faces forward, and applicable on-condition actions, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-12 · published May 14, 2025, effective Jun 18, 2025
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by reports of water leakage from the potable water system due to improperly installed waterline couplings, and water leaking into the electronics equipment (EE) bays from above the floor in the main cabin, resulting in water on the equipment in the EE bays. This AD requires an inspection of seat tracks above the EE bays for missing, damaged, or deteriorated sealant, moisture barrier tape, or tape dams, as applicable, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-08-07 · published May 22, 2025, effective Jun 26, 2025
Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.; Empresa Brasileira de Aeronáutica S.A. (EMBRAER)) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2006-20- 08, which applied to all Embraer S.A. Model EMB-145, -145ER, -145MR, - 145LR, -145XR, -145MP, and -145EP airplanes. AD 2006-20-08 required repetitive inspections to detect cracking or failure of the rod ends and fittings of the aileron power control actuator (PCA), and corrective actions if necessary, and provided an optional terminating action. This AD was prompted by a determination that there was an error in identifying a maintenance task number. This AD continues to require the actions in AD 2006-20-08 and corrects an error in a task number, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-03 · published May 22, 2025, effective Jun 26, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-05 · published May 22, 2025, effective Jun 26, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A321-111, -112, -131, -211, -212, -213, -231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, -253NX, -271NX, and -272NX airplanes. This AD was prompted by the identification of an erroneous value of the main landing gear (MLG) tire width in the aircraft data files used for aircraft performance computation. This AD requires revising the existing airplane flight manual (AFM) to incorporate a complementary performance data file (CPDF) update as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-06 · published May 22, 2025, effective Jun 26, 2025
ATR-GIE Avions de Transport Régional Airplanes
The FAA is superseding Airworthiness Directive (AD) 2023-10- 08, which applied to all ATR--GIE Avions de Transport R[eacute]gional Model ATR42-200, -300, and -320 airplanes. AD 2023-10-08 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2023-10-08, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This AD continues to require certain actions in AD 2023-10-08 and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-07 · published May 22, 2025, effective Jun 26, 2025
Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2015-02- 14, which applied to all Airbus SAS Model A318 series airplanes; A319- 111, -112, -113, -114, -115, -131, -132, and -133 airplanes; A320-211, -212, -214, -231, -232, and -233 airplanes; and A321-111, -112, -131, - 211, -212, -213, -231, and -232 airplanes. AD 2015-02-14 required repetitive inspections for cracking, damage, correct installation, and correct adjustment of the main landing gear (MLG) door hinge and actuator fittings on the keel beam, corrective actions if necessary, and revision of the existing maintenance or inspection program, as applicable. Since the FAA issued AD 2015-02-14, a new design of the MLG door keel beam hinge and actuator fitting was developed. This AD continues to require the actions specified in AD 2015-02-14, adds an optional terminating action, and revises the applicability, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-11-02 · published May 27, 2025, effective Jun 11, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-151N, -153N, -171N, and -173N airplanes; A320-251N, -252N, -253N, -271N, -272N, and -273N airplanes; A321-251N, -251NX, -252N, -252NX, -253N, -253NX, -253NY, -271N, -271NX, -272N, and -272NX airplanes. This AD was prompted by reports of lost synchronization between radio management panels (RMPs). This AD requires revising the existing airplane flight manual (AFM) by providing instructions to address dual loss of RMP data synchronization. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-07-09 · published May 28, 2025, effective Jul 2, 2025
Bombardier, Inc., Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-19- 13, which applied to certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. AD 2020-19-13 required a check to identify the manufacturer and part number of the portable oxygen bottle installation, and, if necessary, modification of the portable oxygen bottle installation. This AD continues to require the actions specified in AD 2020-19-13 and expands the applicability. This AD was prompted by a report indicating that the portable oxygen bottle installation's upper bracket latch assembly can catch on the pressure gauge tube or on the pressure gauge bezel of the portable oxygen bottle. This AD was also prompted by the determination that additional airplanes may be subject to the unsafe condition. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-07-11 · published May 28, 2025, effective Jul 2, 2025
Bombardier, Inc., Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports of engine-driven pump hydraulic pressure hoses for hydraulic systems number 1 and 2 chafing against the pylon in the aft equipment bay. This AD requires an inspection of the engine-driven pump pressure hoses for any damage and minimum clearance between the engine-driven pump hydraulic pressure hose and case drain, suction pressure hose, and surrounding pylon structure; and corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-08-01 · published May 28, 2025, effective Jul 2, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A321-251NX, -252NX, -253NX, -271NX, and -272NX airplanes. This AD was prompted by discovery of two bushes that had migrated on the latch shaft of an emergency overwing exit door (OWED) during accomplishment of an inspection on an in-service airplane. This AD requires repetitive detailed inspections (DETs) of the affected parts and, in case of discrepancies, modification of the affected parts, and prohibits the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-08 · published May 28, 2025, effective Jul 2, 2025
ATR-GIE Avions de Transport Régional Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain ATR--GIE Avions de Transport R[eacute]gional Model ATR42-500 and ATR72-212A airplanes. This AD was prompted by a report of potential use of improper material during the production of vertical tail plane (VTP) fittings. This AD requires, for certain airplanes, an inspection for the material of affected fuselage-to-VTP fittings, an inspection report, and corrective actions, and, for certain other airplanes, part replacement, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-09 · published May 28, 2025, effective Jul 2, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a determination that certain master minimum equipment list (MMEL) items do not comply with MMEL certification requirements. This AD requires revising the operator's existing FAA-approved minimum equipment list (MEL), as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-12 · published May 28, 2025, effective Jul 2, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320 series airplanes; Model A321-211, -212, -213, - 231, -232, -251N, -251NX, -252N, -252NX, -253N, -253NX, -253NY, -271N, -271NX, -272N, and -272NX airplanes; Airbus SAS Model A330-200 series airplanes; Model A330-300 series airplanes; Model A330-800 series airplanes; Model A330-900 series airplanes; Model A350-941 and -1041 airplanes; and Model A380-800 series airplanes. This AD was prompted by a report of corrosion and cracks on the broadband antenna adapter plate during an inspection. This AD requires repetitive general visual inspections of the broadband antenna adapter plate, skirt, vents, and attachment fittings, and applicable corrective actions, and limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-11-06 · published May 30, 2025, effective Jun 16, 2025
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2025-07- 04, which applied to all Airbus Canada Limited Partnership Model BD- 500-1A11 airplanes. AD 2025-07-04 required a review and disposition of all existing repairs and damage assessments for affected structure, corrective actions if necessary, and the prohibition of certain repair engineering orders (REOs). Since the FAA issued AD 2025-07-04, the FAA determined that the list of acceptable generic repair engineering orders (GREOs) specified in table 1 to paragraph (h)(3) of AD 2025-07- 04 was added in error. This AD continues to require review and disposition of all existing repairs and damage assessments for affected structure, which includes GREOs that were identified in AD 2025-07-04, corrective actions if necessary, and the prohibition of certain REOs. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-08-08 · published May 2, 2025, effective Jun 6, 2025
Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model SA341G and SA342J helicopters. This AD was prompted by reports of corrosion on the contact surfaces of the tail rotor inclined and horizontal drive shaft flanges. This AD requires repetitively inspecting the inclined and horizontal drive shaft flanges and, depending on the results, replacing the inclined or horizontal drive shaft. This AD also prohibits installing certain inclined and horizontal drive shafts unless certain requirements are met. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-08-06 · published May 7, 2025, effective Jun 11, 2025
Airbus Helicopters
The FAA is superseding Airworthiness Directive (AD) 2021-09-14 which applied to certain Airbus Helicopters (Airbus) Model SA330J helicopters. AD 2021-09-14 required repetitively inspecting for a gap between the main gearbox (MGB) oil cooling fan assembly (fan) rotor blade and the upper section of the guide vane bearing housing, installing improved MGB fan rotor shaft bearings, and repetitively inspecting the improved MGB fan rotor shaft bearings. Since the FAA issued AD 2021-09-14, Airbus has developed modifications to the components of the MGB fan bearing assembly and issued new material regarding these modifications. This AD retains the actions required by AD 2021-09-14 and also requires installing the improved MGB fan rotor bearing assembly, which constitutes terminating action for the repetitive inspections. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-06 · published May 12, 2025, effective Jun 16, 2025
Leonardo S.p.A. Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.A. Model A119 and AW119 MKII helicopters. This AD was prompted by a report of an electrical failure of the starter-generator, due to a rupture of the drive shaft, which resulted in a partial loss of battery power. This AD requires installing a battery discharge detector and revising the existing Rotorcraft Flight Manual (RFM) for the helicopter. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-09-10 · published May 12, 2025, effective Jun 16, 2025
Leonardo S.p.A. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.A. Model A109E, A109S, and AW109SP helicopters. This AD was prompted by reports of incorrect installation of the motor (MTR) cables and the bonding braids connected to the engine fire extinguisher bottles. This AD requires inspecting the cables and bonding braids installation and, depending on the results, accomplishing corrective action, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-11 · published May 20, 2025, effective Jun 24, 2025
General Electric Company Engines
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model CF6-80E1A2, CF6-80E1A3, CF6-80E1A4, and CF6-80E1A4/B engines. This AD was prompted by a manufacturer investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This AD requires replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-10-04 · published May 22, 2025, effective Jun 26, 2025
General Electric Company Engines
The FAA is adopting a new airworthiness directive (AD) for all General Electric Company (GE) Model CF34-10E2A1, CF34-10E5, CF34- 10E5A1, CF34-10E6, CF34-10E6A1, CF34-10E7, and CF34-10E7-B engines with certain part-numbered high-pressure turbine (HPT) shroud/low pressure turbine (LPT) nozzle assemblies installed. This AD was prompted by a report of failed retention features of the inner and outer support air ducts (commonly referred to as spoolies) discovered during engine disassembly. This AD requires a visual inspection of the combustion case for wear and gouges, repair if necessary, and rework of the affected HPT shroud/LPT nozzle assemblies to add a positive retention of the support air duct. The FAA is issuing this AD to address the unsafe condition on these products.
