25 Airworthiness Directives: 13 airplane, 10 rotorcraft, 2 engine.
AD 2021-09-06 · published May 4, 2021, effective Jun 8, 2021
The Boeing Company Airplanes
The FAA is superseding Airworthiness Directive (AD) 2019-22- 10, which applied to all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. AD 2019-22-10 required repetitive inspections for cracking of the left- and right-hand side outboard chords of frame fittings and failsafe straps at a certain station around eight fasteners, and repair if any cracking is found. For certain airplanes, this AD reduces the compliance time for the initial inspection, and for all airplanes this AD reduces the repetitive interval. This AD was prompted by a determination that the initial inspection threshold and repetitive inspection interval are inadequate to address the cracking in a timely manner. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-12 · published May 4, 2021, effective Jun 8, 2021
Dassault Aviation Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-07- 16, which applied to certain Dassault Aviation Model FALCON 7X airplanes. AD 2020-07-16 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-27 · published May 13, 2021, effective Jun 17, 2021
BAE Systems (Operations) Limited Airplanes
The FAA is adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ series airplanes. This AD was prompted by a report indicating that during a routine battery capacity check on the emergency light power units, the printed circuit boards (PCBs) for certain power units were found to show signs of burning. This AD requires replacing each Honeywell emergency light power unit having a certain part number with a serviceable emergency light power unit. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-15 · published May 14, 2021, effective Jun 1, 2021
Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Model 382, 382B, 382E, 382F, and 382G airplanes, type certificated in any category; and Model C-130A, C-130B, C-130BL, C-130E, C-130H, C-130H-30, C-130J, C-130J-30, EC-130Q, HC-130H, KC-130H, NC-130B, NC-130, and WC- 130H airplanes, type certificated in the restricted or amateur category. This AD was prompted by a crack found on the web attachment flange of the center wing upper forward corner fitting. This AD requires an eddy current surface scan for cracks of the center wing upper and lower forward corner fittings and fasteners, a torque check of the left and right outer-wing-to-center-wing front-beam-web-joint- splice-angle fasteners, and repair, retorqueing, or replacement if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-16 · published May 14, 2021, effective Jun 1, 2021
Bombardier, Inc., Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by a report of a number of low altitude engine surge incidents during takeoff. This AD requires revising the existing airplane flight manual and applicable corresponding operational procedures to provide the flightcrew with procedures to require the engine bleeds to be "ON" during takeoff. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-20 · published May 14, 2021, effective May 14, 2021
ATR-GIE Avions de Transport Régional Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain ATR--GIE Avions de Transport R[eacute]gional Model ATR42-500 and ATR72-212A airplanes. This AD was prompted by reports of temporary loss of all display units and the integrated electronic standby instrument (IESI). This AD requires revising the existing aircraft flight manual (AFM) and applicable corresponding operational procedures to update a systems limitation, limiting dispatch with certain equipment inoperative, performing an operational test of a certain contactor and an electrical test of a certain battery toggle switch, and corrective actions if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-08-14 · published May 18, 2021, effective Jun 2, 2021
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-300, -400, and -500 series airplanes. This AD was prompted by a flap synchro wire failure that may go undetected by the autothrottle (A/T) computer. This AD requires repetitive BITE (built-in test equipment) tests of the A/T computer to detect a flap synchro wire failure, and corrective action if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-13 · published May 19, 2021, effective Jun 23, 2021
ATR-GIE Avions de Transport Régional Airplanes
The FAA is superseding Airworthiness Directives (AD) 2000-23- 04 R1 and AD 2018-20-14, which applied to certain ATR-GIE Avions de Transport R[eacute]gional Model ATR42-500 airplanes. AD 2000-23-04 R1 and AD 2018-20-14 required revising the maintenance or inspection program, as applicable, to incorporate new and/or more restrictive maintenance requirements and airworthiness limitations. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by the FAA's determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-17 · published May 19, 2021, effective Jun 23, 2021
Bombardier, Inc., Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by a report that the inboard multi-function spoiler (MFS) surfaces failed to deploy, which was caused by missing notches on the piston seal of the MFS power control units (PCUs). This AD requires an inspection to determine if affected MFS PCUs are installed, and replacement of affected MFS PCUs. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-11-06 · published May 20, 2021, effective Jun 4, 2021
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by the loss of a windshield in flight, and the consequent rapid depressurization of the flight deck, which caused damage to flight deck items and systems and subsequent thermal shock and overheat, damage to windshield structural plies, and impaired structural integrity of the windshield. This AD requires repetitive inspections and electrical test measurements (EMTs) of affected windshields, and corrective actions if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-18 · published May 27, 2021, effective Jul 1, 2021
ATR-GIE Avions de Transport Régional Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain ATR-GIE Avions de Transport R[eacute]gional Model ATR72-212A airplanes. This AD was prompted by a report of an engine electrical control #1 fault during flight caused by chafing damage on an electrical harness bundle. This AD requires modifying the electrical harness routes and de-icing pipe coupling installations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-13 · published May 27, 2021, effective Jul 1, 2021
De Havilland Aircraft of Canada Limited (Type Certificate Previously Held by Bombardier, Inc.) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2015-17- 08, which applied to certain Bombardier, Inc. Model DHC-8-400 series airplanes. AD 2015-17-08 required installing new cable assemblies with a pull-down resistor. This AD requires modifications to the nose wheel steering (NWS) system. This AD was prompted by a report indicating that several failure modes of the NWS system may cause the loss of feedback from both rotary variable differential transformers to the steering control unit. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-19 · published May 27, 2021, effective Jul 1, 2021
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767-200, -300, -300F, and -400ER series airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations (AWLs) are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-08 · published May 7, 2021, effective Jun 11, 2021
Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 206L series helicopters. This AD was prompted by a manufacturing flaw that could cause low fuel level detector switch units (switch units) to hang in the high position and fail to indicate a low fuel condition. This AD requires removing certain switch units from service and prohibits installing those switch units. This AD also requires accomplishing an operational test of certain other switch units, and depending on the results, removing the switch unit from service. This AD also prohibits installing those certain other switch units unless they pass an operational test. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-24 · published May 14, 2021, effective Jun 18, 2021
Leonardo S.p.a. (Type Certificate Previously Held by Agusta S.p.A.) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2015-25-04 for Agusta S.p.A (now Leonardo S.p.a.) Model A109A and A109A II helicopters. AD 2015-25-04 required inspecting the slider assembly pitch control (slider) for play and replacing the slider if the play exceeds certain limits. This AD was prompted by further investigation that led to the determination that the play was caused by a manufacturing issue. This AD retains certain requirements of AD 2015- 25-04, requires replacing certain part-numbered sliders as a terminating action for the inspections, and prohibits installing the affected part on any helicopter. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-08-02 · published May 17, 2021, effective Jun 21, 2021
Safran Helicopter Engines, S.A. (Type Certificate Previously Held by Turbomeca, S.A.) Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for all Safran Helicopter Engines, S.A. (Safran) Arriel 2D and Arriel 2E model turboshaft engines. This AD was prompted by the manufacturer revising the maintenance and overhaul manuals to introduce new or more restrictive airworthiness limitations and maintenance tasks. This AD requires the replacement of certain critical parts before reaching their published in-service life limits, performing scheduled maintenance tasks before reaching their published periodicity, and performing unscheduled maintenance tasks when the engine meets certain conditions. As a terminating action, this AD requires operators to revise the airworthiness limitation section (ALS) of their existing approved aircraft maintenance program (AMP) by incorporating the revised airworthiness limitations and maintenance tasks. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-09-14 · published May 18, 2021, effective Jun 22, 2021
Airbus Helicopters (Type Certificate Previously Held by Eurocopter France) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2010-16- 51, which applied to certain Eurocopter France (now Airbus Helicopters (Airbus)) Model SA330J helicopters. AD 2010-16-51 required inspecting for a gap between the main gearbox (MGB) oil cooling fan assembly (fan) rotor blade and the upper section of the guide vane bearing housing and depending on the results, replacing the two fan rotor shaft bearings with two airworthy bearings. This AD retains the requirements of AD 2010-16-51 and also requires installing improved MGB fan rotor shaft bearings and repetitively inspecting the new improved MGB fan rotor shaft bearings, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. AD 2010-16-51 was prompted by the separation of a fan rotor blade that caused puncture holes in the transmission deck. This new AD was prompted by the development of an improved MGB fan rotor shaft bearing design. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-01 · published May 18, 2021, effective Jun 2, 2021
Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AW169 helicopters. This AD was prompted by false simultaneous in-flight disengagement of automatic flight control system (AFCS) channels 1 and 2. This AD requires temporarily revising the existing Rotorcraft Flight Manual (RFM) for your helicopter. This AD also requires installing an AFCS software upgrade and concurrently removing that RFM revision. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-03 · published May 18, 2021, effective Jun 22, 2021
Airbus Helicopters
The FAA is superseding Airworthiness Directive (AD) 2019-03-12 for certain Airbus Helicopters Model EC225LP helicopters. AD 2019-03-12 required repetitively inspecting, cleaning, and lubricating each life raft inflation cylinder percussion system bellcrank (bellcrank). This new AD continues to require the actions specified in AD 2019-03-12, and requires replacing any affected bellcrank with a serviceable bellcrank, which terminates the repetitive actions. This AD was prompted by reports of jammed bellcranks in the life raft jettison inflation cylinder percussion system. The actions of this AD are intended to address an unsafe condition on these products.
AD 2021-10-10 · published May 20, 2021, effective Jun 24, 2021
Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model SA330J helicopters. This AD was prompted by the failure of a second stage planet gear installed in the main gearbox (MGB). This AD requires repetitively inspecting the MGB particle detector and the MGB bottom housing (oil sump) for metal particles, analyzing any metal particles that are found, and replacement of the MGB if necessary, as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-14 · published May 20, 2021, effective Jun 24, 2021
Airbus Helicopters Deutschland GmbH Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Deutschland GmbH Model BO-105A, BO-105C, BO- 105S, and BO-105LS A-3 helicopters. This AD was prompted by the FAA's determination that aging of the elastomeric material in a tension torsion strap (TT-strap) could affect the structural characteristics of the TT-strap. This AD requires replacement of certain TT-straps with serviceable parts and implementation of a new storage life limit for TT-straps, as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-15 · published May 27, 2021, effective Jul 1, 2021
Airbus Helicopters Deutschland GmbH Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH Model MBB-BK 117 C-2 and Model MBB- BK 117 D-2 helicopters. This AD was prompted by a determination that a life limit for the adapter forward (FWD) of the outboard load system, repetitive inspections of other components of that system, and for certain helicopters, a modification of the outboard load system, are necessary to address the unsafe condition. This AD requires a modification of the outboard load system for certain helicopters, repetitive inspections of the outboard load system and its components for any defect (including cracking, damage, corrosion, and incorrect installation) and applicable corrective actions, and implementation of a new life limit for the FWD adapter, as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-16 · published May 27, 2021, effective Jul 1, 2021
Carson Helicopters, Inc.; Croman Corporation; Sikorsky Aircraft Corporation; and Siller Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Carson Helicopters, Inc., Model S-61L and SH-3H helicopters; Croman Corporation Model SH-3H helicopters; Sikorsky Aircraft Corporation Model S-61A, S-61D, S-61E, and S-61V helicopters; and Siller Helicopters Model CH-3E and SH-3A helicopters. This AD was prompted by an accident. This AD requires tracking hours time-in-service (TIS) and external lift cycles (lift cycles) for certain main gearbox left and right input freewheel unit (IFWU) assemblies. This AD also requires determining the type of IFWU assembly installed and depending on the results, calculating the moving average, repetitive inspections, recording certain information, replacing parts, and marking parts. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-06 · published May 4, 2021, effective May 10, 2021
CFM International, S.A. Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) LEAP-1B model turbofan engines. This AD was prompted by multiple reports of pressure sub-system (PSS) unit faults due to pressure transducer corrosion following extended storage periods. For an engine in service, this AD requires checks for engine maintenance messages related to the pressure transducer and, depending on the results of the check, replacement of the PSS unit before further flight. The AD requires this repetitive check for faults prior to each flight until the PSS has accumulated at least 15 hours of electrical power. For an engine not in service, this AD requires applying electrical power to the PSS unit before further flight. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-10-09 · published May 20, 2021, effective Jun 24, 2021
CFM International, S.A. Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for all CFM International, S.A. (CFM) CFM56-5B and CFM56-7B model turbofan engines with a certain high-pressure turbine (HPT) inner stationary seal installed. This AD was prompted by cracks found in the rotating air HPT front seal. This AD requires removal, inspection, and replacement of the affected HPT inner stationary seal and, depending on the findings, replacement of the rotating air HPT front seal, HPT rotor blades, and No. 3 ball bearing. The FAA is issuing this AD to address the unsafe condition on these products.
