48 Airworthiness Directives: 38 airplane, 5 rotorcraft, 3 engine, 1 appliance, 1 various.
AD 2014-14-04 · published Aug 1, 2014, effective Sep 5, 2014
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2003-18-10 for certain The Boeing Company Model 767 airplanes. AD 2003-18-10 required revising the Airworthiness Limitations Section of the maintenance planning data (MPD) document. This new AD also requires revising the maintenance program to incorporate an additional limitation, which terminates the existing requirements; and adds airplanes to the applicability. This AD was prompted by a re-evaluation of certain doors and flaps based on their fatigue-critical nature. We are issuing this AD to detect and correct fatigue cracking of the principal structural elements (PSEs), which could adversely affect the structural integrity of the airplane.
AD 2014-15-08 · published Aug 1, 2014, effective Sep 5, 2014
Beechcraft Corporation (Type Certificate Previously Held by Hawker Beechcraft Corporation; Raytheon Aircraft Company) Airplanes
We are adopting a new airworthiness directive (AD) for certain Beechcraft Corporation (Type Certificate Previously Held by Hawker Beechcraft Corporation; Raytheon Aircraft Company) Model Hawker 800XP, 850XP, and 900XP airplanes. This AD was prompted by a design review that revealed there were no instructions to apply sealant to structural components in the fuel tank during the winglet installation process. This AD requires an inspection for the presence of sealant on doubler plate edges, doubler plate rivets, and adjacent skin in the fuel vent surge tanks; and corrective actions if necessary. We are issuing this AD to detect and correct missing sealant, which, during a lightning strike, could result in a potential source of ignition in a fuel tank and consequent explosion or fire and subsequent in-flight breakup of the airplane.
AD 2014-15-09 · published Aug 1, 2014, effective Sep 5, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200 Freighter, A330-200 and -300, and A340-200, -300, -500, and -600 series airplanes. This AD was prompted by reassessment of an unsafe condition related to MZ-type spoiler servo-controls (SSCs) that did not remain locked in the retracted position (hydraulic locking function) after manual depressurization of the corresponding hydraulic circuit. This reassessment resulted in the determination that performing repetitive operational tests of all SSC types is necessary. This AD requires repetitive operational tests of the hydraulic locking function on each SSC installed on the blue or yellow hydraulic circuits, and replacing any affected SSC with a serviceable SSC. We are issuing this AD to detect and correct loss of the hydraulic locking function during take-off, which, in combination with one inoperative engine, could result in reduced controllability of the airplane.
AD 2014-15-11 · published Aug 1, 2014, effective Sep 5, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL- 600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by two in-service reports of fracture of the rudder pedal tubes installed on the pilot-side rudder bar assembly. This AD requires repetitive inspections for cracking and damage of the pilot-side rudder pedal tubes, and corrective action if necessary. This AD also provides optional terminating action for the repetitive inspections. We are issuing this AD to detect and correct cracked and damaged pilot-side rudder pedal tubes, which could result in loss of function of the pilot's rudder pedal during flight, takeoff, or landing, and could result in reduced controllability of the airplane.
AD 2014-15-16 · published Aug 1, 2014, effective Aug 18, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A319-111, -112, -115, -132, and -133 airplanes; Model A320-214, -232, and -233 airplanes; and Model A321-211, -231, and -232 airplanes. This AD requires a detailed inspection for missing fasteners on the frame between certain stringers; for certain airplanes, a rototest inspection of the fastener holes for cracking; and corrective actions if necessary. This AD was prompted by a report that when the cabin lining was removed during a cabin conversion it was discovered that fasteners were missing on the frame. We are issuing this AD to detect and correct missing fasteners which, if not corrected, could affect the structural integrity of the airframe and could result in rapid decompression.
AD 2014-13-12 · published Aug 5, 2014, effective Sep 9, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of silicon particles inside the oxygen generator manifolds, which had chafed from the mask hoses during installation onto the generator outlets. This AD requires identifying the part number and serial number of each passenger oxygen container, replacing the oxygen generator manifold of any affected oxygen container with a serviceable manifold, and performing an operational check of the manual mask release, and corrective actions if necessary. We are issuing this AD to detect and correct non-serviceable oxygen generator manifolds, which could reduce or block the oxygen supply and result in injury to passengers when oxygen supply is needed.
AD 2014-15-04 · published Aug 5, 2014, effective Sep 9, 2014
Saab AB, Saab Aerosystems Airplanes
We are adopting a new airworthiness directive (AD) for certain Saab AB, Saab Aerosystems Model SAAB 2000 airplanes. This AD was prompted by a report of rudder pedal restriction which was the result of water leakage at the inlet tubing of an in-line heater in the lower part of the forward fuselage. This AD requires deactivating the potable water system, or alternatively filling and activating the potable water system. We are issuing this AD to prevent rudder pedal restriction due to the pitch control mechanism becoming frozen as the result of water spray, which could prevent disconnection and normal pitch control, and consequently result in reduced controllability of the airplane.
AD 2014-15-12 · published Aug 5, 2014, effective Sep 9, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-600, -700, -700C, -800, -900 and -900ER series airplanes. This AD was prompted by reports of incorrectly installed bolts common to the rear spar termination fitting on the horizontal stabilizer. This AD requires inspecting for a serial number that starts with the letters "SAIC" on the left- and right-side horizontal stabilizer identification plate; inspecting for correct bolt protrusion and chamfer of the bolts of the rear spar termination fitting of the horizontal stabilizer, if necessary; inspecting to determine if certain bolts are installed, if necessary; and doing related investigative and corrective actions if necessary. We are issuing this AD to prevent loss of structural integrity of the horizontal stabilizer attachment and loss of control of the airplane.
AD 2014-15-14 · published Aug 5, 2014, effective Sep 9, 2014
the Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 89-12-10, for certain The Boeing Company Model 747 airplanes. AD 89-12-10 required replacement of certain underwing fuel tank access doors with stronger, fire-resistant doors. This new AD requires inspecting certain fuel tank access doors for installation of impact-resistant doors, and stencils and index markers; corrective actions if necessary; revising the maintenance program to incorporate certain new airworthiness limitations; and adding airplanes to the applicability. This AD was prompted by a report of a standard access door installed instead of an impact-resistant access door and stencils missing from some impact- resistant access doors and adjacent wing skin. We are issuing this AD to prevent foreign object penetration of the fuel tank, which could cause a fuel leak near an ignition source (e.g., hot brakes or engine exhaust nozzle), consequently leading to a fuel-fed fire.
AD 2014-15-18 · published Aug 5, 2014, effective Aug 20, 2014
Mooney International Corporation Airplanes
We are adopting a new airworthiness directive (AD) for certain Mooney International Corporation Models M20C, M20E, M20M, M20R, and M20TN airplanes. This AD requires inspection of the outer empennage attach fittings for correct thickness with replacement as necessary. This AD was prompted by discovery of empennage attach fittings (Lugs) that do not meet the approved design dimensional requirements, which could result in possible reduction in fatigue or static strength and/or corrosion. We are issuing this AD to correct the unsafe condition on these products.
AD 2014-16-03 · published Aug 5, 2014, effective Sep 9, 2014
Fuji Heavy Industries, Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for Fuji Heavy Industries, Ltd. Models FA-200-160, FA-200-180, and FA-200-180AO airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as deterioration of brake performance due to seal defects caused by deterioration due to age of the O-rings of the brake master cylinder. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2014-16-02 · published Aug 12, 2014, effective Aug 12, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-1A11 (CL-600) airplanes. This AD requires revising the airplane flight manual to prohibit thrust reverser operation, and repetitive detailed inspections of both engine thrust reversers for cracks and modification if necessary. The modification of the thrust reversers is also an optional terminating action for the repetitive inspections. This AD was prompted by reports of partial deployment of an engine thrust reverser in-flight caused by a failure of the translating sleeve at the thrust reverser attachment points. We are issuing this AD to detect and correct cracks of the translating sleeve at the thrust reverser actuator attachment points, which could result in deployment or dislodgement of an engine thrust reverser in- flight and subsequent reduced control of the airplane.
AD 2014-15-20 · published Aug 15, 2014, effective Sep 19, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by reports of failure of the high pressure shutoff valves (HPSOVs) causing the timer and monitor unit (TMU) to become inoperative since the HPSOV and the TMU are on the same circuit breaker. This AD requires a wiring modification to segregate the HPSOV power supply from the TMU. We are issuing this AD to prevent an inoperative TMU, which could result in the loss of the automatic de-icing mode, and lead to an increased workload for the flight crew and loss of control of the airplane.
AD 2014-15-21 · published Aug 15, 2014, effective Sep 19, 2014
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2006-26-06 for certain The Boeing Company Model 777-200 and -300 series airplanes equipped with Rolls-Royce engines. AD 2006-26-06 required repetitive inspections to detect cracks of the outer V-blades of the thrust reverser, and corrective action if necessary. AD 2006-26-06 also provided for an optional terminating action for the repetitive inspections. This new AD adds, for airplanes on which the optional terminating action is done, repetitive inspections for cracking in the outer V-blade fittings of the hinge beam and latch beam ends of each thrust reverser half, and replacement of an affected thrust reverser half if necessary. This new AD also adds airplanes to the applicability. This AD was prompted by reports of cracked outer V- blade fittings at the hinge beam end of Rolls-Royce engine thrust reversers, on airplanes on which the optional terminating action was done. We are issuing this AD to prevent separation of a thrust reverser from the airplane during normal reverse thrust or during a refused takeoff, which could result in unexpected thrust asymmetry and a possible runway excursion.
AD 2014-16-04 · published Aug 15, 2014, effective Sep 19, 2014
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 2008-14-17 for certain Airbus Model A330-200 and A340-300 series airplanes. AD 2008- 14-17 required a high frequency eddy current (HFEC) inspection, corrective actions if necessary, and modifications. This new AD requires the same actions as those required by AD 2008-14-17, but with a reduced compliance time. This AD was prompted by a determination from a fatigue and damage tolerance evaluation that the compliance time needs to be revised. We are issuing this AD to detect and correct damage of the upper shell structure at the skin and frame interface, which could result in reduced structural integrity of the airframe.
AD 2014-16-16 · published Aug 15, 2014, effective Sep 2, 2014
Empresa Brasileira de Aeronautica S.A. (Embraer) Airplanes
We are adopting a new airworthiness directive (AD) for all Embraer S.A. Model ERJ 190-100 STD, -100 LR, -100 ECJ, -100 IGW, -200 STD, -200 LR, and -200 IGW airplanes. This AD requires, for certain airplanes, retorquing and replacing the pylon outboard and inboard lower link fittings. For all airplanes, this AD requires repetitive retorquing of the pylon outboard and inboard lower link fittings. This AD was prompted by a report of a loose lower link assembly on the left and right pylons. We are issuing this AD to prevent loss of a shear pin on the pylon outboard and inboard lower link fittings, which could result in failure of the fitting and consequent separation of the engine from the wing.
AD 2013-13-13 · published Aug 19, 2014, effective Sep 23, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A310 series airplanes; and Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called A300-600 series airplanes). This AD was prompted by the revision of certain airworthiness limitation items (ALI) documents, which require more restrictive maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program to incorporate the limitations section. We are issuing this AD to prevent fatigue cracking, damage, or corrosion in principal structural elements, which could result in reduced structural integrity of the airplane.
AD 2014-16-06 · published Aug 19, 2014, effective Sep 23, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B16 (CL-604 Variant) airplanes. This AD was prompted by reports of in-flight uncommanded rudder movements. This AD requires revising the airplane flight manual (AFM) to incorporate an uncommanded yaw motion procedure. We are issuing this AD to prevent in- flight uncommanded rudder movements, which could lead to structural failure and subsequent loss of the airplane.
AD 2014-16-07 · published Aug 19, 2014, effective Sep 23, 2014
Bombardier, Inc. Airplanes
We are superseding Airworthiness Directive (AD) 2011-15-09 for certain Bombardier, Inc. Model DHC-8-400, -401, and -402 airplanes. AD 2011-15-09 required repetitive inspections for proper operation of the main landing gear (MLG) alternate extension system (AES), and corrective actions if necessary. This new AD requires, for certain airplanes, new repetitive inspections for proper operation of the MLG AES, and corrective actions if necessary. This new AD also requires eventually replacing the MLG AES cam mechanism assembly with a new assembly, which terminates the repetitive inspections for those airplanes. This AD was prompted by a determination that, for certain airplanes not affected by AD 2011-15-09, a different MLG AES cam mechanism assembly was installed, resulting in input lever fractures and inability to open the MLG door; those assemblies could be subject to the same unsafe condition in AD 2011-15-09. We are issuing this AD to prevent improper operation of the cam mechanism or rupture of the door release cable, which could result in loss of control of the airplane during landing.
AD 2014-16-08 · published Aug 19, 2014, effective Sep 23, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-215-6B11 (CL-215T Variant), and CL-215-6B11 (CL-415 Variant) airplanes. This AD was prompted by several reports indicating that shorter nacelle strut bushings were inadvertently installed on certain airplanes. This AD requires a general visual inspection of the left and right nacelle upper strut bushings; installation of the bolts and preload indicating (PLI) washers, if necessary; and replacement of the bushing or repair of the bushing installation, if necessary. We are issuing this AD to detect and correct inadequate nacelle strut bushings, which provide insufficient engagement in the strut fork end, and could deform under the bearing load and lead to the failure of the joint.
AD 2014-16-09 · published Aug 19, 2014, effective Sep 23, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 707 airplanes, Model 720 and 720B series airplanes, Model 727 airplanes, and Model 737-100, -200, and -200C series airplanes. This AD was prompted by a report of a fire that originated near the first officer's area and caused extensive damage to the flight deck on a different airplane model. This AD requires replacing the low-pressure oxygen hoses with non-conductive low- pressure oxygen hoses in the flight compartment. We are issuing this AD to prevent electrical current from inadvertently passing through an internal, anti-collapse spring of the low-pressure oxygen hose, which can cause the low-pressure oxygen hose to melt or burn, leading to an oxygen-fed fire and/or smoke in the flight deck.
AD 2014-16-11 · published Aug 19, 2014, effective Sep 23, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 series airplanes. This AD was prompted by reports of smoke or flames in the passenger cabin of various transport category airplanes related to the wiring for the passenger cabin in-flight entertainment (IFE) system, cabin lighting, and passenger seats. This AD requires, for certain airplanes, doing an inspection of the electrical power control panel for a certain part number, and corrective action if necessary; and, for certain other airplanes, installing a new electrical power control panel, and making changes to the wiring and certain electrical load management system (ELMS) panels. We are issuing this AD to ensure that the flightcrew is able to turn off electrical power to the IFE systems and other non- essential electrical systems through one or two switches in the flight deck in the event of smoke or flames. In the event of smoke or flames in the airplane flight deck or passenger cabin, the flightcrew's inability to turn off electrical power to the IFE system and other non- essential electrical systems could result in the inability to control smoke or flames in the airplane flight deck or passenger cabin during a non-normal or emergency situation, and consequent loss of control of the airplane.
AD 2014-16-14 · published Aug 19, 2014, effective Sep 23, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD was prompted by reports in which a single, undetected, erroneous radio altimeter output caused the autothrottle to enter landing flare retard mode prematurely on approach. This AD requires removing certain autothrottle computers and installing a new or reworked autothrottle computer. We are issuing this AD to prevent a single, undetected, erroneous radio altimeter output from causing premature autothrottle landing flare retard and subsequent loss of automatic speed control, which could result in loss of control of the airplane.
AD 2014-15-13 · published Aug 21, 2014, effective Sep 25, 2014
Bombardier, Inc. Airplanes
We are superseding Airworthiness Directive (AD) 2005-15-04 for certain Bombardier, Inc. Model CL-600-1A11 (CL-600), CL-600-2A12 (CL- 601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. AD 2005-15-04 required operators to assign serial numbers or part numbers to certain landing gear parts; establish the number of landings on the parts, if necessary; and revise the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness (ICA) to reflect the new life limits of the landing gear parts. This new AD adds airplanes to the applicability, requires operators to assign serial numbers or part numbers to certain additional landing gear parts to establish the number of landings on the parts if necessary, and requires operators to record in all required airplane technical records and manuals the new part numbers, serial numbers, and landings assigned to these parts. This AD was prompted by reports that landing gear parts that have safe-life limits but do not have serial numbers or part numbers can be removed from one landing gear and re-installed on another, making tracking difficult. We are issuing this AD to prevent life-limited landing gear parts from being used beyond their safe-life limits, which could lead to collapse of the landing gear.
AD 2014-15-51 · published Aug 21, 2014, effective Aug 21, 2014
Embraer S.A. Airplanes
We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model EMB-500 airplanes. This AD was sent previously to all known U.S. owners and operators of these airplanes as an emergency AD. This AD requires an inspection and replacement as necessary of the barrel nuts at the horizontal stabilizer to vertical stabilizer attachment joint. This AD was prompted by mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracking of the barrel nuts at the horizontal stabilizer to vertical stabilizer attachment joint. We are issuing this AD to correct the unsafe condition on these products.
AD 2014-16-19 · published Aug 21, 2014, effective Sep 25, 2014
Airbus Airplanes
We are superseding Airworthiness Directives (AD) 2006-21-08, AD 2007-14-01, AD 2008-25-02, AD 2010-04-09, AD 2011-01-02, and AD 2012-16-05, for certain Airbus Model A330 and A340 series airplanes. AD 2006-21-08, AD 2007-14-01, AD 2008-25-02, AD 2010-04-09, AD 2011-01-02, and AD 2012-16-05 required revising the maintenance program or inspection program to incorporate certain maintenance requirements and airworthiness limitations for fuel tank systems. This new AD requires a new maintenance or inspection program revision. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. We are issuing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2014-16-20 · published Aug 21, 2014, effective Sep 25, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A300 series airplanes. This AD was prompted by an analysis of the impacts of extended service goal activities on Airbus Model A300 series airplanes. This AD requires revising the maintenance or inspection program. We are issuing this AD to prevent failure of flight critical systems.
AD 2014-16-22 · published Aug 21, 2014, effective Sep 25, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200 Freighter, A330-200, A330-300, and A340-200, A340-300, A340-500, and A340-600 series airplanes. This AD was prompted by a determination that the service life limits of the cabin pressure control system (CPCS) safety valves installed on the aft pressure bulkhead were being exceeded. This AD requires repetitive replacement of the CPCS safety valves with serviceable valves. We are issuing this AD to prevent exceeding the service life limits of the CPCS safety valves, which, in the event of a failure, could result in excessive positive or negative differential pressure in the fuselage and consequent incapacitation or injuries to airplane occupants.
AD 2014-16-17 · published Aug 25, 2014, effective Sep 29, 2014
Air Tractor, Inc. Airplanes
We are superseding Airworthiness Directive (AD) 2010-17-18 R1, which applies to certain Air Tractor, Inc. Models AT-802 and AT-802A airplanes. AD 2010-17-18 R1 required repetitively inspecting (using the eddy current method) the two outboard fastener holes in both of the wing main spar lower caps at the center splice joint for cracks; repairing or replacing any cracked spar; changing the safe life for certain serial number ranges; and sending the inspection results, only if cracks are found, to the FAA. This new AD retains all actions of AD 2010-17-18 R1 and expands the applicability to include all serial numbers regardless of configuration or operational use. This AD was prompted by our determination that the safe life for the wing main spar lower caps should apply to all Models AT-802 and AT-802A airplanes regardless of configuration or operational use. We are issuing this AD to correct the unsafe condition on these products.
AD 2014-16-13 · published Aug 27, 2014, effective Oct 1, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A300 series airplanes. This AD was prompted by our determination of the need to incorporate new life limits for the main landing gear (MLG) barrel assembly, retraction actuator assembly linkage, and flange duct. This AD requires revising the maintenance or inspection program, as applicable, to include the new life limits. We are issuing this AD to prevent reduced structural integrity of the airplane and possible loss of controllability of the airplane.
AD 2014-16-26 · published Aug 27, 2014, effective Oct 1, 2014
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 900EX airplanes. This AD was prompted by our determination to introduce a corrosion prevention control program, among other changes, to the maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to include the maintenance tasks and airworthiness limitations specified in the Airworthiness Limitations section of the airplane maintenance manual. We are issuing this AD to prevent reduced structural integrity and reduced controllability of the airplane.
AD 2014-16-27 · published Aug 27, 2014, effective Oct 1, 2014
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 900EX airplanes. This AD was prompted by our determination of the need for a revision to the airplane airworthiness limitations to introduce a corrosion prevention control program, among other changes, to the maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to include the maintenance tasks and airworthiness limitations specified in the Airworthiness Limitations section of the airplane maintenance manual. We are issuing this AD to prevent reduced structural integrity of the airplane, and prevent reduced controllability of the airplane.
AD 2014-17-01 · published Aug 27, 2014, effective Sep 16, 2014
Viking Air Limited Airplanes
We are adopting a new airworthiness directive (AD) for Viking Air Limited Model DHC-3 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as looseness of the horizontal stabilizer actuator mounting block in the forward-aft and side-to-side directions. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2014-17-04 · published Aug 27, 2014, effective Oct 1, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by reports that elevator power control unit (PCU) shear pins may fail prematurely. This AD requires repetitive replacement of the elevator PCU shear pins. We are issuing this AD to prevent premature elevator PCU shear pin failure. If all pins fail on one elevator, the elevator surface would become inoperative, which could reduce the controllability of the airplane and could result in a loss of redundancy for flutter prevention.
AD 2014-16-05 · published Aug 28, 2014, effective Oct 2, 2014
Embraer S.A. Airplanes
We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 170 airplanes. This AD was prompted by reports of "BLEED 1(2) LEAK" messages displayed on the engine indication and crew alert system (EICAS), and indirect damage to components of the electrical wiring interconnection system (EWIS) in the engine pylon area. This AD requires inspecting the EWIS components for damage, and repair if necessary. This AD also requires installing pre-cooler deflectors on the left- and right-hand pylons, and applying silicone sealant. We are issuing this AD to prevent indirect damage to EWIS components near the engine bleed air pre-coolers, which could result in a dual engine roll back to idle and consequent dual engine power loss and reduced controllability of the airplane.
AD 2014-16-18 · published Aug 28, 2014, effective Oct 2, 2014
BAE Systems (Operations) Limited Airplanes
We are adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 series airplanes and Model Avro 146-RJ series airplanes. This AD was prompted by reports of cracking of the main fitting of the nose landing gear (NLG). This AD requires revising the maintenance program by incorporating a new safe- life limitation for the NLG main fitting. We are issuing this AD to prevent collapse of the NLG, which could lead to degradation of direction control on the ground or an un-commanded turn to the left, and a consequent loss of control of the airplane on the ground, possibly resulting in damage to the airplane and injury to occupants.
AD 2014-16-21 · published Aug 28, 2014, effective Oct 2, 2014
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 7X airplanes. This AD was prompted by reports that the pintle pins installed on a certain number of airplanes may be incorrectly protected against corrosion. This AD requires replacing certain pintle pins on the left- and right-hand main landing gear (MLG) with a serviceable part. We are issuing this AD to detect and correct pintle pins that have been incorrectly corrosion-protected, which could cause the pintle pins to shear under normal load and lead to the collapse of the MLG during take-off or landing.
AD 2014-17-10 · published Aug 28, 2014, effective Sep 12, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD requires repetitive on-ground power cycles (resets) of the Transponder, Terrain and Traffic Collision Avoidance System (T3CAS). This AD was prompted by reports of spurious terrain ahead warning system (TAWS) alerts during approach and takeoff. We are issuing this AD to prevent spurious TAWS alerts, which could increase flightcrew workload during critical landing or takeoff phases, and result in reduced control of the airplane.
AD 2014-12-11 · published Aug 4, 2014, effective Sep 8, 2014
Sikorsky Aircraft Corporation Helicopters
We are adopting a new airworthiness directive (AD) for the Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopter. This AD requires revising the Rotorcraft Flight Manual (RFM) to include the appropriate operating limitations for performing Class D external load- combination operations. This AD was prompted by an inaccurate RFM provision, which was approved without appropriate limitations for this model helicopter for carrying Class D external rotorcraft-load combinations, including human external cargo (HEC). The actions are intended to require appropriate operating limitations to allow operators to perform Class D external load-combination operations, including HEC, in this model helicopter that now meets the Category A performance standard.
AD 2014-07-51 · published Aug 5, 2014, effective Aug 20, 2014
AgustaWestland S.p.A. Helicopters
We are publishing a new airworthiness directive (AD) for certain AgustaWestland S.p.A. Model AB139 and AW139 helicopters. This AD requires repetitively inspecting the Main Rotor (M/R) Rotating Scissors for play of the Lower Half Scissor Spherical Bearing (bearing) and removing the bearing if there is play beyond allowable limits. This AD also requires removing all affected bearings. This AD is prompted by reports of certain bearings dislodging from certain M/R Rotating Scissors. These actions are intended to detect excessive play of the bearing and prevent failure of the M/R Rotating Scissors and subsequent loss of control of the helicopter.
AD 2014-12-51 · published Aug 5, 2014, effective Aug 20, 2014
Airbus Helicopters (Previously Eurocopter France)
We are publishing a new airworthiness directive (AD) for Airbus Helicopters Model EC130B4 and EC130T2 helicopters, which was sent previously to all known U.S. owners and operators of these helicopters. This AD requires repetitively inspecting the Fenestron to tailboom junction frame (junction frame) for a crack. This AD is prompted by reports of a crack propagating through the junction frame on two EC130B4 helicopters. These actions are intended to detect a crack and to prevent failure of the junction frame, which could result in loss of the Fenestron and subsequent loss of control of the helicopter.
AD 2014-16-01 · published Aug 5, 2014, effective Aug 20, 2014
MD Helicopters, Inc., Helicopters
We are adopting a new airworthiness directive (AD) for MD Helicopters, Inc. (MDHI), Model MD900 helicopters. This AD requires an eddy current inspection of the main rotor upper hub assembly (upper hub) for a crack and replacing the upper hub with an airworthy upper hub before further flight if there is a crack. This AD is prompted by a report of cracks on an upper hub at the blade attach holes. The actions specified by this AD are intended to detect a crack in the upper hub to prevent failure of the upper hub and subsequent loss of control of the helicopter.
AD 2014-16-24 · published Aug 21, 2014, effective Sep 25, 2014
Airbus Helicopters Deutschland GmbH (Previously Eurocopter Deutschland GbmH) (Airbus Helicopters) Helicopters
We are superseding Airworthiness Directive (AD) 2012-10-53 for Eurocopter Deutschland GmbH (ECD) (now Airbus Helicopters) Model EC135P1, EC135P2, EC135P2+, EC135T1, EC135T2, and EC135T2+ helicopters. AD 2012-10-53 required, before further flight and at specified intervals, checking and inspecting the upper and lower main rotor hub (MRH) shaft flanges for a crack, and inspecting the lower hub-shaft flange bolt attachment areas for a crack. Since we issued AD 2012-10- 53, it has been determined that it is safe to increase the visual inspection intervals of the MRH shaft flanges from 10 hours time-in- service (TIS) to 50 hours TIS and remove the inspection of the lower MRH shaft flange bolt attachment areas. This new AD continues to require checking and inspecting the upper and lower MRH shaft flanges for a crack. These actions are intended to detect a crack on the MRH shaft flange, which if not corrected, could result in failure of the MRH and subsequent loss of control of the helicopter.
AD 2014-16-15 · published Aug 15, 2014, effective Sep 19, 2014
Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Makila 2A and Makila 2A1 turboshaft engines. This AD requires initial and repetitive visual inspections, and replacement of the splines of the high-pressure (HP) fuel pump/metering valve and the module M01 drive gear, if necessary. This AD was prompted by the failure of two HP fuel pumps that resulted in engine in-flight shutdowns. We are issuing this AD to prevent failure of the HP fuel pump, which could lead to an in-flight shutdown, damage to the engine, and forced landing or accident.
AD 2014-16-10 · published Aug 19, 2014, effective Sep 23, 2014
Rolls-Royce plc Turbofan Engines
We are superseding airworthiness directive (AD) 2013-12-01 for all Rolls-Royce plc (RR) model RB211 Trent 768-60, 772-60, and 772B-60 turbofan engines. AD 2013-12-01 required a one-time ultrasonic inspection (UI) of low-pressure (LP) compressor blades with more than 2,500 flight cycles since new or last inspection. This AD requires initial and repetitive UIs of the affected LP compressor blades. This AD was prompted by LP compressor blade partial airfoil release events. We are issuing this AD to prevent LP compressor blade airfoil separations, damage to the engine, and damage to the airplane.
AD 2014-17-03 · published Aug 28, 2014, effective Oct 2, 2014
Technify Motors GmbH Reciprocating Engines
We are adopting a new airworthiness directive (AD) for certain Technify Motors GmbH (type certificate previously held by Thielert Aircraft Engines GmbH) TAE 125-02-99 and TAE 125-02-114 reciprocating engines. This AD requires removal of each high-pressure (HP) fuel pump before 300 flight hours (FHs) in service or within 55 FHs after the effective date of the AD, whichever occurs later. This AD was prompted by in-flight shutdowns on airplanes with TAE 125-02 engines. We are issuing this AD to prevent failure of the HP fuel pump, which could result in damage to the engine and damage to the airplane.
AD 2014-16-28 · published Aug 27, 2014, effective Oct 1, 2014
Empresa Brasileira de Aeronautica S.A. (Embraer)
We are adopting a new airworthiness directive (AD) for certain Empresa Brasileira de Aeronautica S.A. (Embraer) Model EMB-135BJ airplanes. This AD was prompted by reports of failure of the bolts that connect the cockpit windshield center-post to the forward fuselage. This AD requires repetitive detailed inspections to detect discrepancies on the attaching parts of the cockpit windshield center- post; checking whether the bolts are tightened, if applicable; and modifying parts, including inspecting for and repairing damage. We are issuing this AD to prevent failed bolts and failed attaching parts of the cockpit windshield center-post, which could lead to loss of structural integrity of the airplane.
AD 2014-17-02 · published Aug 25, 2014, effective Sep 9, 2014
Honeywell ASCa Inc. Emergency Locator Transmitters Installed on Various Transport Category Airplanes
We are superseding Airworthiness Directive (AD) 2013-18-09 for certain Honeywell ASCa Inc. emergency locator transmitters (ELTs) installed on various transport category airplanes. AD 2013-18-09 required various one-time general visual inspections of the ELT transmitter units (TUs), and corrective actions if necessary. This new AD corrects the manufacturer's name in the AD applicability and adds a source of approval for an installation. AD 2013-18-09 was prompted by a fire on a parked and unoccupied airplane; preliminary information indicated combustion in the area of the ELT TU. This new AD was prompted by the identification of an error in the applicability of AD 2013-18-09. We are issuing this AD to detect and correct discrepancies of the battery wiring installation inside the TU, which could result in an electrical short and possible ignition source.
