34 Airworthiness Directives: 25 airplane, 2 rotorcraft, 6 engine, 1 glider.
AD 2014-13-05 · published Jul 1, 2014, effective Aug 5, 2014
British Aerospace Regional Aircraft Airplanes
We are superseding Airworthiness Directive (AD) 2007-10-16 for all British Aerospace Regional Aircraft Jetstream Model 3201 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the need to incorporate revisions to the Airworthiness Limitations section of the Instructions for Continued Airworthiness. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2014-12-13 · published Jul 10, 2014, effective Jul 25, 2014
the Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2014-03-06 for all the Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. AD 2014-03-06 required repetitive inspections for cracking of the aft support fitting for the main landing gear (MLG) beam, and the rear spar upper chord and rear spar web in the area of rear spar station (RSS) 224.14; and repair if necessary. This AD clarifies two paragraph references. This AD was prompted by a determination that two paragraph references were in error. We are issuing this AD to detect and correct cracking of the aft support fitting for the main landing gear (MLG) beam, and the rear spar upper chord and rear spar web in the area of rear spar station (RSS) 224.14, which could grow and result in a fuel leak and possible fire.
AD 2013-22-23 R1 · published Jul 11, 2014, effective Jul 11, 2014
AERMACCHI S.p.A. Airplanes
We are rescinding Airworthiness Directive (AD) 2013-22-23 for AERMACCHI S.p.A. Models F.260, F.260B, F.260C, F.260D, F.260E, F.260F, S.208, and S.208A airplanes equipped with a Lycoming O-540, IO-540, or AEIO-540 (depending on the airplane model) wide cylinder flange engine with a front crankcase mounted propeller governor. AD 2013-22-23 resulted from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. We issued the AD to detect and correct improper position of the set screw, which could lead to complete loss of engine oil pressure and result in emergency landing. Since we issued AD 2013-22-23, we have determined the unsafe condition does not exist specific to the airplane design features.
AD 2014-11-03 · published Jul 15, 2014, effective Aug 19, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. This AD was prompted by reports of severe corrosion on bonding jumpers installed on the flight control surfaces. This AD requires repetitive bonding jumper inspections for corrosion, sealant disbond, and insufficient sealant coverage; and corrective actions if necessary. This AD also specifies an optional inspection for corrosion damage of the bonding brackets, and corrective actions if necessary, which would terminate the repetitive inspections. For certain airplanes, this AD requires installing certain bonding jumpers, and replacing single-tabbed brackets with two-tabbed brackets. We are issuing this AD to detect and correct corrosion on bonding jumpers installed on the flight control surfaces, which, in the event of a lightning strike, could damage the actuator control electronics (ACEs) and result in the loss of the ability to command individual flight control surfaces or cause uncommanded motion of individual flight control surfaces.
AD 2014-11-10 · published Jul 15, 2014, effective Aug 19, 2014
Bombardier, Inc. Airplanes
We are superseding Airworthiness Directive (AD) 2008-08-09 for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. AD 2008-08-09 required revising the airworthiness limitations (AWL) section of the Instructions for Continued Airworthiness by incorporating procedures for repetitive functional tests of the pilot input lever of the pitch feel simulator (PFS) units and corrective actions if necessary. This new AD requires replacing certain PFS units with new redesigned PFS units, which would terminate the repetitive functional tests; and both adding and removing certain airplanes from the applicability. This AD was prompted by reports that the shear pin in the input lever of several PFS units failed due to fatigue; and by the development of a re-designed PFS unit, which eliminates the need for repetitive functional tests. We are issuing this AD to prevent undetected failure of the shear pins of both PFS units simultaneously, which could result in loss of pitch feel forces and consequent reduced control of the airplane.
AD 2014-13-06 · published Jul 15, 2014, effective Aug 19, 2014
Learjet Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Learjet Inc. Model 45 airplanes. This AD was prompted by a report of two cases of premature corrosion found on the structural support flange for the engine thrust reverser. This AD requires inspecting for any corrosion, and damage to the sealant; installing sealants and gaskets; and related investigative and corrective actions as necessary. We are issuing this AD to prevent failure of the thrust reverser structural support, which could result in departure of the thrust reverser from the engine that could subsequently result in damage to the adjacent support structure and engine controls, airframe structure, and control surfaces. Departing thrust reversers could also result in injury to persons on the ground.
AD 2014-13-07 · published Jul 15, 2014, effective Aug 19, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-300, -400, -500, -600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by a review of the tail strobe light installation, which revealed that the tail strobe light is not electrically bonded to primary structure of the airplane. This AD requires installing a new tail strobe light housing and a new disconnect bracket, and changing the wire bundles. This AD also requires, for certain airplanes, an inspection to determine if sealant is applied, and corrective actions if necessary. We are issuing this AD to prevent, in case of a direct lightning strike to the tail strobe light, damage to the operation of other critical airplane systems due to electromagnetic coupling and large transient voltages, and damage to the control mechanisms or surfaces due to a fire, which could result in loss of control of the airplane.
AD 2014-13-10 · published Jul 15, 2014, effective Aug 19, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by a report of installation of incorrect wire support clamps within the bay area of the left and right environmental control systems (ECS) during production; the ECS bay area is a flammable fluid leakage zone. Use of incorrect wire support clamps that are not fully cushioned could allow electrical power wiring to come in contact with the exposed metal of the improper clamp, causing a short circuit and subsequent electrical arcing. This AD requires inspecting to identify the part number of the wire support clamp, and related investigative and corrective actions if necessary. We are issuing this AD to prevent electrical arcing and a potential ignition source, which, in combination with flammable fuel vapors, could result in a fuel tank explosion, and consequent loss of the airplane.
AD 2014-13-11 · published Jul 15, 2014, effective Aug 19, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 707 airplanes, and Model 720 and 720B series airplanes. This AD was prompted by reports of scribe-line-related fatigue cracks on Model 727 airplanes, which are similar in design to Model 707 airplanes, and Model 720 and 720B series airplanes. This AD requires inspections for scribe lines in the skin lap joints, external approved repairs, external features, skin butt joints, and decals; and related investigative and corrective actions if necessary. This AD also requires surface finish restoration. We are issuing this AD to detect and correct scribe lines, which can develop into fatigue cracks in the skin and cause rapid decompression of the airplane.
AD 2014-13-15 · published Jul 15, 2014, effective Aug 19, 2014
EADS CASA (Type Certificate Previously Held by Construcciones Aeronauticas, S.A.) Airplanes
We are adopting a new airworthiness directive (AD) for certain EADS CASA (Type Certificate Previously Held by Construcciones Aeronauticas, S.A.) Model CN-235-300 airplanes. This AD was prompted by reports of reduced thickness of the center fuselage lower skin panel. This AD requires a detailed inspection to determine the presence of panel thickness reduction; and repetitive nondestructive testing (NDT) inspections and repair if necessary. We are issuing this AD to detect and correct reduced thickness of lower panel joints, which could result in reduced fatigue and damage tolerant characteristics of the lower panel joint to the adjacent side panels and failure of the center fuselage lower skin panel, resulting in loss of control of the airplane.
AD 2014-13-16 · published Jul 15, 2014, effective Aug 19, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by the finding of an uncertified main landing gear (MLG) inboard retraction actuator bracket pin installed on an in- service airplane. This AD requires inspection of the MLG inboard retraction actuator bracket for a part number, and replacement if necessary. We are issuing this AD to detect and correct uncertified pins in the MLG inboard retraction actuator bracket, which could result in pin failure, leading to an MLG extension without damping, and a potential for MLG structural damage and possible collapse during landing.
AD 2014-13-17 · published Jul 15, 2014, effective Aug 19, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A300 series airplanes; Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. This AD was prompted by reports of failures of the right inner tank fuel pump. This AD requires repetitive functional tests of the circuit breakers for the fuel pump power supply, and replacement of certain circuit breakers. We are issuing this AD to detect and correct failure of the circuit breakers for the fuel pump power supply, which could result in a fuel pump overheating, leading to a fuel tank explosion.
AD 2014-13-18 · published Jul 15, 2014, effective Aug 19, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model DHC-8-102, -103, and -106 airplanes; and DHC-8- 200 and DHC-8-300 series airplanes. This AD was prompted by a report of a beta warning horn (BWH) system failing to activate when the beta mode was triggered. This AD requires modifying the BWH microswitch installation. We are issuing this AD to prevent the inadvertent activation of ground beta mode during flight, which could lead to engine overspeed, engine damage or failure, and consequent reduced controllability of the airplane.
AD 2014-14-03 · published Jul 15, 2014, effective Jul 15, 2014
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2014-07-01, for certain The Boeing Company Model 747 airplanes. AD 2014-07-01 required repetitive inspections for cracking in certain bulkhead structure; inspections of certain fasteners and support frame modifications on certain airplanes; related investigative and corrective actions, if necessary; and an interim modification that would terminate certain repetitive inspections. This AD clarifies certain paragraph references and revises a compliance time. This AD was prompted by a determination that certain paragraph references are in error. We are issuing this AD to detect and correct fatigue cracking of the BS 2598 bulkhead structure, which could adversely affect the structural integrity of the bulkhead and the horizontal stabilizer support structure, and result in loss of controllability of the airplane.
AD 2014-13-08 · published Jul 23, 2014, effective Aug 27, 2014
Diamond Aircraft Industries GmbH Airplanes
We are superseding Airworthiness Directive (AD) 2013-24-14 for Diamond Aircraft Industries GmbH Models DA40 and DA40F airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the fatigue strength found in the aft main spar not ensuring unlimited lifetime structural integrity. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2014-13-14 · published Jul 23, 2014, effective Aug 27, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A310 series airplanes. This AD was prompted by a report of an electrical arc and a hydraulic haze in the wheel bay of the left- hand main landing gear (MLG), possibly resulting from chafing between a hydraulic high pressure hose and electrical wiring of the green electrical motor pump (EMP). This AD requires modification of the electrical routing and replacement of the union elbows. We are issuing this AD to prevent chafing of hydraulic pressure hoses and electrical wiring of the green EMPs, which, in combination with a system failure, could cause an uncontrolled and undetected fire in the MLG bay.
AD 2014-14-05 · published Jul 23, 2014, effective Aug 27, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A320-111, -211, -212, and -231 airplanes. This AD was prompted by reports of broken struts of the center wing box (CWB). This AD requires a detailed inspection of the CWB struts for cracking, and repair if necessary. We are issuing this AD to detect and correct cracked or broken struts, which could result in strut failure and consequent reduced structural integrity of the airplane.
AD 2014-14-06 · published Jul 23, 2014, effective Aug 27, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes; Model A319-111, -112, -113, - 114, and -115 airplanes; Model A320-111, -211, -212, and -214 airplanes; and Model A321-111, -112, -211, -212, and -213 airplanes. This AD was prompted by reports of broken aft engine mount retainers. This AD requires inspecting the aft engine mount retainers for surface finish, and for cracks and failure, and replacement if necessary. We are issuing this AD to prevent failure of retainer brackets of the aft engine mount and consequent loss of the locking feature of the nuts of the inner and outer pins; loss of the pins will result in the aft mount engine link no longer being secured to the aft engine mount.
AD 2014-15-01 · published Jul 23, 2014, effective Aug 27, 2014
M7 Aerospace LLC Airplanes
We are adopting a new airworthiness directive (AD) for M7 Aerospace LLC Models SA227-AT, SA227-AC, SA227-BC, SA227-CC, and SA227- DC airplanes equipped with a bayonet shear pin main cabin door latching mechanism. This AD was prompted by fatigue cracks found in the internal door surround doubler, the fuselage external skin, and the door corner fittings at the fuselage upper forward corner of the main cabin door cutout. This AD requires repetitively inspecting the four corners of the main cabin door cutout for cracks, making necessary repairs, and reporting inspection results to M7 Aerospace LLC. We are issuing this AD to correct the unsafe condition on these products.
AD 2014-13-13 · published Jul 28, 2014, effective Sep 2, 2014
Fokker Services B.V. Airplanes
We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by reports that the bracket of the rod in the carbon fiber reinforced plastic (CFRP) main landing gear (MLG) outboard door had detached. In addition, we received reports of broken recessed heads on titanium attachment bolts of the operating rod brackets on the modified CFRP MLG outboard doors. This AD requires a detailed inspection of the CFRP MLG outboard door for play or cracks in the recessed countersunk heads of the operating rod bracket attachment bolts; replacement of the bolt if necessary; and, for certain airplanes, modification of the CFRP MLG outboard doors and attachment to the MLG. We are issuing this AD to detect and correct the affected MLG from moving to the down and locked position, which could result in MLG collapse during landing or roll- out, and consequent damage to the airplane and injury to passengers.
AD 2014-15-05 · published Jul 28, 2014, effective Sep 2, 2014
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A310-304, -322, -324, and -325 airplanes. This AD was prompted by reports of insufficient clearance between the fuel quantity indicator (FQI) probes and the adjacent structure and metallic components in the wing fuel tanks. This AD requires a one-time detailed visual inspection for sufficient clearance between FQI probes on both the left-hand side and right-hand side of the trim horizontal stabilizer and the adjacent structure and metallic components in the fuel tanks, and modification if necessary. We are issuing this AD to detect and correct insufficient clearance, which could lead to electrical arcing in a fuel tank during a lightning strike, which could result in ignition and consequent fire or explosion in the fuel tank.
AD 2014-15-06 · published Jul 28, 2014, effective Sep 2, 2014
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100B SUD, 747-200B, 747-300, 747-400, and 747-400D series airplanes. This AD was prompted by an evaluation by the design approval holder (DAH) indicating that the upper deck tension ties are subject to widespread fatigue damage (WFD). This AD requires repetitive inspections for cracking in the upper deck tension ties, and related investigative and corrective actions if necessary; tension tie replacement; and post-replacement repetitive inspections for cracking in the upper deck tension ties, and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct fatigue cracking of the upper deck tension ties. Severed or disconnected tension ties at multiple locations could result in rapid decompression and loss of structural integrity of the airplane.
AD 2014-15-07 · published Jul 28, 2014, effective Sep 2, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 airplanes. This AD was prompted by reports of a fractured wing-to-fuselage strut attachment joint bolt. This AD requires a torque check of all wing-to-fuselage strut attachment joint bolts, and repair or replacement if necessary. For certain airplanes, this AD also requires a detailed inspection for corrosion, damage, and wear of each wing-to-fuselage strut attachment joint bolt and associated hardware, and replacement if necessary; and a borescope inspection for corrosion and damage of the bore hole and barrel nut threads, and repair or replacement if necessary. We are issuing this AD to detect and correct fractured strut attachment joint bolts, which could result in reduced structural integrity of the wing-to-fuselage strut attachment joint and subsequent loss of the wing.
AD 2014-15-10 · published Jul 28, 2014, effective Sep 2, 2014
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 7X airplanes. This AD was prompted by a report of a crew alerting system message caused by an inversion of the wiring in the slats control manifold (SCM). This AD requires an operational test of the SCM, and replacing the affected SCM with a serviceable SCM if necessary. We are issuing this AD to detect and correct inversion of the wiring in the SCM, which could lead to a commanded retraction of the median and outboard slats in flight, and result in reduced controllability of the airplane.
AD 2014-15-17 · published Jul 31, 2014, effective Jul 31, 2014
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B16 (CL-604 Variant) airplanes. This AD requires revising the airplane flight manual to incorporate temporary revisions that introduce additional limitations for operation of taxi and landing lights. This AD was prompted by a determination that there is a potential for fuel leakage from auxiliary power unit (APU) boost pump component installations in the right-hand landing lights compartment. We are issuing this AD to advise the flightcrew of the limitations for taxi lights and landing lights to prevent heat generated by the taxi lights and landing lights on the ground reaching the auto-ignition temperature of the fuel, which could potentially ignite any fuel or fumes present in the right-hand landing lights compartment.
AD 2014-06-51 · published Jul 15, 2014, effective Jul 30, 2014
Airbus Helicopters Deutschland GmbH (Airbus Helicopters) (Type Certificate Previously Held by Eurocopter Deutschland GmbH) Helicopters
We are publishing a new airworthiness directive (AD) for Airbus Helicopters Model MBB-BK 117 A-3, MBB-BK 117 A-4, MBB-BK 117 B- 1, and MBB-BK 117 C-2 helicopters with a certain Metro Aviation, Inc. (Metro), vapor-cycle air conditioning kit pulley (pulley) installed, which was sent previously to all known U.S. owners and operators of these helicopters. This AD supersedes AD 2013-12-06, which required inspecting the pulley for looseness and properly installed lockwire and re-installing the pulley. Since we issued AD 2013-12-06, we received a report of a possible design and manufacturing deficiency in some pulleys wherein they did not have sufficient thread depth, allowing the pulley to detach from the rotor brake disc. This AD requires inspecting each pulley attaching bolt hole to determine if there is sufficient depth of the threads and either removing the pulley if the depth is insufficient or installing dual locking tabs under each pulley attaching bolt if the depth is sufficient. These actions are intended to prevent the pulley from detaching, resulting in damage to the tail rotor (T/R) driveshaft, and subsequent loss of control of the helicopter.
AD 2014-13-09 · published Jul 15, 2014, effective Jul 30, 2014
Airbus Helicopters Deutschland GmbH (Type Certificate Previously Held by Eurocopter Deutschland GmbH Helicopters) (AHD)
We are adopting a new airworthiness directive (AD) for AHD Model EC135P1, P2, P2+, T1, T2, and T2+ helicopters. This AD requires repetitive visual inspections of the ring frame X9227 for a crack and, if there is a crack, replacing the ring frame before further flight. This AD is prompted by a fatigue crack in the ring frame. These actions are intended to detect a crack in the ring frame and prevent loss of the tail rotor and subsequent loss of control of the helicopter.
AD 2014-11-05 · published Jul 1, 2014, effective Aug 5, 2014
Pratt & Whitney Canada Corp. Turboprop Engines
We are adopting a new airworthiness directive (AD) for certain Pratt & Whitney Canada Corp. (P&WC) turboprop engines. This AD requires installing a reinforcement liner to the power turbine (PT) containment ring and, for certain PT containment rings, adding scallops. This AD was prompted by in-service events involving the perforation of engine cases as a result of the liberation of PT blades and the fracture/ displacement of the PT containment ring. We are issuing this AD to prevent uncontained engine failure and damage to the airplane.
AD 2014-13-02 · published Jul 1, 2014, effective Aug 5, 2014
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce plc (RR) RB211-Trent 875-17, 877-17, 884-17, 884B-17, 892- 17, 892B-17, and 895-17 turbofan engines. This AD requires inspection of the affected low-pressure (LP) turbine bearing support and exhaust case assembly and, if necessary, its replacement with a part eligible for installation. This AD was prompted by thin-walled LP turbine bearing support and exhaust case assemblies having been delivered into service. We are issuing this AD to prevent failure of the LP turbine bearing support and exhaust case assembly, which could lead to engine separation and damage to the airplane.
AD 2014-12-52 · published Jul 11, 2014, effective Jul 28, 2014
Honeywell International Inc. (Type Certificate Previously Held by AlliedSignal Inc., Garrett Turbine Engine Company) Turbofan Engines
We are superseding emergency airworthiness directive (AD) 2014-12-52 for all Honeywell International Inc. TFE731-4, -4R, -5AR, - 5BR, -5R, -20R, -20AR, -20BR, -40, -40AR, -40R, -40BR, -50R, and -60 turbofan engines. Emergency AD 2014-12-52 was sent previously to all known U.S. owners and operators of these engines. AD 2014-12-52 required, before further flight, a review of the engine logbook maintenance records to determine if any affected engines are installed. AD 2014-12-52 also prohibited operation of an airplane with two or more affected engines that have 2nd stage low-pressure turbine (LPT2) blades with less than 250 operating hours since new. This AD retains the requirements of AD 2014-12-52 and clarifies the intent of the mandatory requirements. This AD was prompted by reports of LPT2 blade separations. We are issuing this AD to prevent LPT2 blade failure, multiple engine in-flight shutdowns, and damage to the airplane.
AD 2014-14-01 · published Jul 11, 2014, effective Aug 15, 2014
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce plc (RR) RB211 Trent 768-60, 772-60, and 772B-60 turbofan engines. This AD requires modification of the engine by removing an electronic engine control (EEC) incorporating EEC software standard A14 or earlier and installing an EEC eligible for installation. This AD was prompted by an uncontained multiple turbine blade failure on an RR RB211 Trent 772B turbofan engine. We are issuing this AD to prevent failure of the intermediate-pressure (IP) turbine disk drive arm or burst of the high-pressure turbine disk, which could lead to uncontained engine failure and damage to the airplane.
AD 2014-14-02 · published Jul 11, 2014, effective Aug 15, 2014
Pratt & Whitney Canada Corp. Turboprop Engines
We are adopting a new airworthiness directive (AD) for certain Pratt & Whitney Canada Corp. (P&WC) PW120, PW121, PW121A, PW124B, PW127, PW127E, PW127F, PW127G, and PW127M turboprop engines. This AD requires removal of the O-ring seal from the fuel manifold fitting. This AD was prompted by reports of fuel leaks at the interface between the fuel manifold and the fuel nozzle that resulted in engine fire. We are issuing this AD to prevent in-flight fuel leakage, which could lead to engine fire, damage to the engine, and damage to the airplane.
AD 2014-15-03 · published Jul 23, 2014, effective Aug 27, 2014
Pratt & Whitney Canada Corporation Turboprop Engines
We are adopting a new airworthiness directive (AD) for certain serial number Pratt & Whitney Canada Corporation (P&WC) model PW150A turboprop engines. This AD requires rerouting of the igniter cables and installation of new support brackets. This AD was prompted by reports of damage to a high-pressure fuel line, which could result in a high- pressure fuel leak into the engine nacelle. We are issuing this AD to prevent high-pressure fuel leaks, which could cause engine fire and damage to the engine and the airplane.
AD 2014-15-02 · published Jul 23, 2014, effective Aug 27, 2014
GROB-WERKE GMBH & CO KG Gliders
We are adopting a new airworthiness directive (AD) for GROB- WERKE GMBH & CO KG Models G102 STANDARD ASTIR III, G102 CLUB ASTIR III, and G102 CLUB ASTIR IIIb gliders and BURKHART GROB LUFT--UND RAUMFAHRT GmbH & CO KG Models G103 TWIN II, G103A TWIN II ACRO, G103C TWIN III ACRO, and G 103 C Twin III SL gliders. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as plastic control cable pulleys developing cracks due to aging. We are issuing this AD to require actions to address the unsafe condition on these products.
