38 Airworthiness Directives: 23 airplane, 9 rotorcraft, 6 engine.
AD 2013-04-07 · published Mar 5, 2013, effective Apr 9, 2013
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 airplanes. This AD was prompted by reports of the loss of the fixed frequency system, leading to the loss of power to the left and right buses and all systems serviced by these buses. This AD requires modification of the wiring and changes to existing airworthiness limitations. We are issuing this AD to prevent loss of the fixed frequency system, which could lead to loss of a number of the pilot's and co-pilot's flight instruments, in addition to other avionics systems.
AD 2013-04-08 · published Mar 5, 2013, effective Apr 9, 2013
Diamond Aircraft Industries GmbH Airplanes
We are adopting a new airworthiness directive (AD) for Diamond Aircraft Industries GmbH Model H-36, HK 36 R, HK 36 TS, and HK 36 TTS airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as installation of an unsuitable self-locking nut on the bell crank of the elevator push rod that can cause failure of the elevator, resulting in loss of control. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-04-09 · published Mar 5, 2013, effective Apr 9, 2013
Costruzioni Aeronautiche Tecnam srl Airplanes
We are adopting a new airworthiness directive (AD) for Costruzioni Aeronautiche Tecnam srl Model P2006T airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as multiple cracks found on the outboard aileron hinge support of a P2006T airplane during an inspection. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-04-10 · published Mar 5, 2013, effective Apr 9, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A310-203, -204, -222, -304, -322, and -324 airplanes. This AD was prompted by a design review of the fuel tank access covers and analyses comparing compliance of the access covers to different tire burst models. `Type 21' panels located within the debris zone revealed that they could not sustain the impact of the tire debris. This AD requires modifying the wing manhole surrounds and replacing certain fuel access panels. We are issuing this AD to prevent a possibility of a fire due to tire debris impact on the fuel access panels.
AD 2013-04-03 · published Mar 7, 2013, effective Apr 11, 2013
Cessna Aircraft Company Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company Model 750 airplanes. This AD was prompted by reports of loss of displayed airspeed. This AD requires inspecting certain logic modules to determine if certain cabin altitude/pitot static heater module assemblies are installed and replacing those assemblies with a new assembly; and revising the Non-Normal Procedures Section of the airplane flight manual (AFM) to include procedures for resetting the pitot switch in the event of pitot heater failure and for total loss of airspeed indication. We are issuing this AD to prevent the loss of all displayed airspeed, which could result in reduced ability to control the airplane.
AD 2013-04-11 · published Mar 7, 2013, effective Apr 11, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -800, and -900ER series airplanes. This AD was prompted by incorrect wire support clamps installed within the left environmental control systems (ECS) bay, which could allow wiring to come in contact with the exposed metal of the improper clamp. This AD requires inspections to identify the part number of the wire support clamp, related investigative actions, and corrective actions if necessary. We are issuing this AD to prevent electrical arcing and a potential ignition source within the ECS bay, which in combination with flammable fuel vapors, could result in a center wing fuel tank explosion, and consequent loss of the airplane.
AD 2013-04-12 · published Mar 7, 2013, effective Apr 11, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A310-204, -222, -304, -322, and -324 airplanes. This AD was prompted by the manufacturer re-classifying slat extension eccentric bolts as principle structural elements (PSE) with replacement due at or before newly calculated fatigue life limits. This AD requires replacing slat extension eccentric bolts and associated washers with new slat extension eccentric bolts and washers. We are issuing this AD to prevent fatigue cracking, which could result in the loss of structural integrity of the airplane.
AD 2013-04-13 · published Mar 7, 2013, effective Apr 11, 2013
BAE SYSTEMS (OPERATIONS) LIMITED Airplanes
We are adopting a new airworthiness directive (AD) for all BAE SYSTEMS (OPERATIONS) LIMITED Model BAe 146 and Avro 146-RJ series airplanes. This AD was prompted by a report that certain ceramic terminal blocks, through which the wiring for the engine fire extinguishers, fire detection circuits, and engine and intake anti-ice system are routed, have been found to have moisture ingress, which can degrade the insulation resistance of the ceramic terminal blocks. This AD requires a one-time insulation resistance test of ceramic terminal blocks, and if necessary, replacement of the blocks. We are issuing this AD to prevent latent failure of the number 2 fire bottle, which, in the event of an engine fire, could result in failure of the fire bottle to discharge when activated and possibly preventing the flightcrew from extinguishing an engine fire.
AD 2013-03-06 · published Mar 11, 2013, effective Apr 15, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200 Freighter, -200, and -300 series airplanes; and Model A340-200, -300, -500, and -600 series airplanes. This AD was prompted by a report that erroneous height indication by one radio altimeter with engaged flare and retard mode, in case of go-around, might lead to a temporary loss of airplane longitudinal control. This AD requires revising the airplane flight manual. We are issuing this AD to ensure that the flightcrew applies the appropriate operational procedures in the event of an erroneous indication of the radio altimeter, which could result in temporary loss of airplane longitudinal control.
AD 2013-05-02 · published Mar 11, 2013, effective Apr 15, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 airplanes. This AD was prompted by reports of cracks of the hinge bearing lugs of the center section ribs of the horizontal stabilizer. This AD requires repetitive high frequency eddy current (HFEC) inspections for cracking of the left and right rib hinge bearing lugs of the aft face of the center section of the horizontal stabilizer; measuring crack length and blending out cracks; and replacing the horizontal stabilizer center section rib, if necessary. We are issuing this AD to detect and correct cracking in the hinge bearing lugs of the horizontal stabilizer center section ribs, which could result in failure of the lugs, and consequent inability of the horizontal stabilizer to sustain the required limit loads and loss of control of the airplane.
AD 2013-03-22 · published Mar 13, 2013, effective Apr 17, 2013
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by reports that airplanes with a Class C cargo (baggage) compartment have liners that do not meet flammability requirements. This AD requires replacing the existing cargo compartment liners with liners that comply. We are issuing this AD to prevent inadequate fire protection in the cargo compartment and consequent uncontrolled fire.
AD 2013-04-14 · published Mar 13, 2013, effective Apr 17, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300- 600 series airplanes); and Model A310 series airplanes. This AD was prompted by a report of an uncommanded slide back of the co-pilot seat to the end stop position. This AD requires a one-time inspection for a part number, a tensile test of the affected seats, and corrective actions if necessary. We are issuing this AD to detect and prevent unwanted movement of a pilot or co-pilot seat in the horizontal direction, which could lead to inadvertent input on the flight control commands and possibly result in loss of controllability of the airplane.
AD 2013-06-02 · published Mar 18, 2013, effective Apr 8, 2013
Diamond Aircraft Industries GmbH Airplanes
We are adopting a new airworthiness directive (AD) for Diamond Aircraft Industries GmbH Models DA 42 M-NG and DA 42 NG airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the engine air inlet filter is subject to icing. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-05-06 · published Mar 20, 2013, effective Apr 24, 2013
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2A12 (CL-601) and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. This AD was prompted by reports of jamming/malfunctioning of the left-hand engine thrust control mechanism. This AD requires modifying the left-hand engine upper core-cowl. We are issuing this AD to prevent jamming/ malfunctioning of the left-hand engine thrust control mechanism, which could lead to loss of control of the airplane.
AD 2013-05-09 · published Mar 20, 2013, effective Apr 24, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200, -300, and -200 Freighter series airplanes; and all Airbus Model A340-200 and -300 series airplanes. This AD was prompted by a determination that the bonding lead from a certain isolation valve to a frame was too close to an electrical harness, which might cause chafing between the electrical harness and the associated bonding lead. This chafing could lead to a short circuit of the isolation valve and consequent non-closure of the isolation valve, which would prevent the air flow to be shut off in case of fire. This AD requires modifying the bonding lead installation of the isolation valve. We are issuing this AD to prevent such chafing, which could result in non-closure of the isolation valve in the event of a fire and consequent damage to the airplane and injury to its occupants.
AD 2013-05-03 · published Mar 21, 2013, effective Apr 25, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. This AD was prompted by fuel system reviews conducted by the manufacturer. This AD requires doing an inspection to identify the part number of the motor-operated valve (MOV) actuators of the main and center fuel tanks; replacing certain MOV actuators with new MOV actuators; and measuring the electrical resistance of the bond from the adapter plate to the airplane structure, and doing corrective actions if necessary. We are issuing this AD to prevent electrical current from flowing through an MOV actuator into a fuel tank, which could create a potential ignition source inside the fuel tank. This condition, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
AD 2013-05-05 · published Mar 21, 2013, effective Apr 25, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. This AD was prompted by reports of in-service events related to electrical power system malfunctions resulting in damage to electrical load management system (ELMS) P200 and P300 power panels and the surrounding area. This AD requires installing enclosure trays to contain debris in certain ELMS panels, and replacing certain ELMS contactors. We are issuing this AD to prevent contactor failures, which could result in uncontained hot debris flow due to ELMS contactor breakdown, consequent smoke and heat damage to airplane structure and equipment during ground operations, and possible injuries to passengers and crew.
AD 2013-05-07 · published Mar 21, 2013, effective Apr 25, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767 airplanes. This AD was prompted by reports of stiff operation of the elevator pitch control system and jammed elevator controls. This AD requires replacing pressure seal assemblies; doing repetitive inspections for dirt, loose particles, or blockage of the flanged tube and drain hole for the pressure seals, and corrective action if necessary; replacing the aft air-intake duct assembly with a new or modified assembly and installing a dripshield; and installing gutters on the horizontal stabilizer center section and modifying the side brace fittings. We are issuing this AD to prevent moisture from collecting and freezing on the elevator control system components, which could limit the ability of the flightcrew to make elevator control inputs and result in reduced controllability of the airplane.
AD 2008-07-11 R1 · published Mar 25, 2013, effective Mar 25, 2013
PILATUS AIRCRAFT LTD. Airplanes
We are rescinding an airworthiness directive (AD) for all PILATUS AIRCRAFT LTD. Models PC-12, PC-12/45, and PC-12/47 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. We issued that AD to mandate new life limits for the pitch trim actuator and pitch trim actuator attachment parts. If these new limitations were not mandated, the pitch trim actuator and the pitch trim actuator components could fail. This failure could lead to an unsafe flying configuration. Since we issued that AD, we have determined that the unsafe condition addressed in that AD is now addressed in another AD.
AD 2013-05-10 · published Mar 29, 2013, effective May 3, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777 airplanes. This AD was prompted by reports that escape slides/rafts did not deploy due to galvanic corrosion of the door-mounted slide/raft packboard release mechanisms. This AD requires doing a general visual inspection of the housing assembly of the packboard release mechanism to determine if its surface treatment has been sealed, and if the surface of the housing assembly is unsealed, replacing the housing assembly with a new or serviceable housing assembly. We are issuing this AD to detect and correct corrosion of the packboard release mechanisms, which could interfere with escape slide/raft deployment, prohibit doors from opening in the armed mode, and cause consequent delay and injury during evacuation of passengers and crew from the cabin in the event of an emergency.
AD 2013-05-12 · published Mar 29, 2013, effective May 3, 2013
Embraer S.A. Airplanes
We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 170 and ERJ 190 airplanes. This AD was prompted by a report that high rate discharge (HRD) bottle explosive cartridges of a cargo compartment fire extinguisher system were swapped between the forward and aft cargo compartments. Additional investigation also revealed the possibility of swapping between the electrical connectors of the HRD and low rate discharge (LRD) bottles, and a rotated installation of the HRD bottle. Improper assembly of the fire extinguishing bottle might cause the extinguishing agent to be discharged toward the unselected cargo compartment rather than toward the cargo compartment with fire. This AD requires an inspection of the HRD bottle for correct installation and to determine if the pressure switch is in the correct position, and re-installation if necessary; an inspection of the HRD and LRD bottle discharge heads to determine the part number, and replacement if necessary; and, for certain airplanes, an inspection to identify the HRD and LRD bottle electrical connectors, and relocation if necessary. We are issuing this AD to prevent the inability of the fire extinguishing system to suppress fire.
AD 2013-06-03 · published Mar 29, 2013, effective May 3, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of oil residue between the stator and the rotor parts of the position resolvers of the angle of attack (AOA) vane, which was a result of incorrect removal of the machining oil during the manufacturing process of the AOA resolvers. This AD requires an inspection to determine if certain AOA probes are installed, and replacement of any affected AOA probe. We are issuing this AD to prevent erroneous AOA information and consequent delayed or non- activation of the AOA protection systems, which during flight at a high AOA, could result in reduced control of the airplane.
AD 2013-06-04 · published Mar 29, 2013, effective May 3, 2013
REIMS AVIATION S.A. Airplanes
We are adopting a new airworthiness directive (AD) for REIMS AVIATION S.A. Model F406 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as fretting (wear and/or chafing) found between the elevator pushrod assembly and the horizontal tail structure, which could cause the elevator pushrod to jam and could result in loss of control. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-04-06 · published Mar 11, 2013, effective Apr 15, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for the Eurocopter France (Eurocopter) Model AS332C, AS332L, and AS332L1 helicopters. This AD requires modifying the main landing gear control panel (control panel) 33G, connector 100G, and wiring. It also requires tests to ensure that these modifications function correctly. This AD was prompted by reports of electro-valve power supply disruptions while a helicopter is on the ground, causing the landing gear to retract and the helicopter nose to drop. This results in damage to the forward section of the helicopter's bottom structure. The actions of this AD are intended to prevent an uncommanded landing gear retraction that would cause the helicopter nose to drop and hit the ground while the rotor blades are spinning.
AD 2012-26-06 · published Mar 12, 2013, effective Apr 16, 2013
Sikorsky Aircraft-Manufactured Model S-64F Helicopters
We are adopting a new airworthiness directive (AD) for Sikorsky Aircraft Corporation-manufactured Model S-64F helicopters, now under the Erickson Air-Crane Incorporated (Erickson) Model S-64F type certificate. This AD supersedes an existing AD which requires inspections, rework, and replacement, if necessary, of the main gearbox (MGB) second stage lower planetary plate (plate). Since we issued that AD, the manufacturer has conducted a configuration review and analysis, and a review of the service history of certain components. The actions of this AD are intended to establish life limits for certain components, remove various parts from service, and require consistency in the part numbers of certain four bladed tail rotor (T/R) assemblies to prevent fatigue cracking, failure from static overload, and subsequent loss of control of the helicopter.
AD 2013-05-23 · published Mar 20, 2013, effective Apr 24, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS332C, L, and L1 helicopters to require a one-time inspection of the main rotor head (MRH) swash-plate upper bearing (bearing) for a non-smooth point (friction point). This AD was prompted by a report of the premature deterioration of the MRH bearing of the rotating star installed on a Model AS332L1 helicopter. The actions of this AD are intended to detect deterioration of the MRH bearing and to prevent overloading the scissor links which drive the main rotor system, failure of the scissors links, and subsequent loss of control of the helicopter.
AD 2013-05-14 · published Mar 22, 2013, effective Apr 26, 2013
Bell Helicopter Textron, Inc.
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron, Inc. (Bell), Model 412 and 412EP helicopters. This AD requires establishing a lower life limit on certain swashplate outer ring assemblies (outer ring), revising the retirement life on the components' history card or equivalent record, and revising the maintenance manual or Instructions for Continued Airworthiness (ICA). This AD also prohibits installing these outer rings on any helicopter. This AD was prompted by reports of cracking in the outer rings. The actions are intended to prevent failure of an outer ring because of cracking, which could lead to the loss of main rotor (M/R) blade pitch control and subsequent loss of helicopter control.
AD 2013-05-17 · published Mar 22, 2013, effective Apr 26, 2013
Sikorsky Aircraft Corporation Helicopters
We are adopting a new airworthiness directive (AD) for Sikorsky Aircraft Corporation (Sikorsky) Model S-61A, D, E, L, N, NM, R, and V helicopters to require replacing each forward and aft fuel system 40 micron fuel filter element with a 10 micron nominal (40 micron absolute) fuel filter element. This AD was prompted by a National Transportation Safety Board (NTSB) review of in-service events where engine performance degradation occurred, and the review determined that some of these events were caused by contaminants larger than 10 microns present in the engine fuel control units (FCUs). The actions are intended to prevent particulate contamination in the FCU, which could lead to malfunction of an internal valve, power loss at a critical phase of flight, and loss of control of the helicopter.
AD 2013-05-15 · published Mar 26, 2013, effective Apr 30, 2013
Robinson Helicopter Company Helicopters
We are adopting a new airworthiness directive (AD) for Robinson Helicopter Company (Robinson) Model R44 and R44 II helicopters equipped with emergency floats. This AD requires replacing the inflation valve assembly. This AD was prompted by the failure of the emergency floats to deploy during a factory test because a needle was binding within the inflation valve assembly. The actions are intended to prevent the failure of the floats to inflate during an emergency landing.
AD 2013-05-16 · published Mar 26, 2013, effective Apr 30, 2013
Hughes Helicopters, Inc., and McDonnell Douglas Helicopter Systems (Type Certificate Is Currently Held by MD Helicopters, Inc.) Helicopters
We are adopting a new airworthiness directive (AD) for MD Helicopters, Inc. (MDHI) Model 369D, 369E, 369F, and 369FF helicopters with certain serial-numbered tailboom assemblies. This AD requires measuring the distance between aft longeron rivets and the outboard edge of frame rings. If the distance is too short to ensure a safe flight, the AD requires installing a doubler. This AD was prompted by the discovery of short-edge margin conditions on two tailboom assemblies. The actions are intended to detect a short-edge margin condition, prevent failure of the tailboom and loss of control of the helicopter.
AD 2013-05-21 · published Mar 26, 2013, effective Apr 30, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model EC130 B4 helicopters with a cabin vibration damper installed. This AD requires installing a vibration damper casing assembly on both sides of the helicopter. This AD was prompted by a crack and failure of a cabin vibration damper blade. The actions of this AD are intended to modify the cabin vibration damper assembly to prevent contact with the flight controls in the event of a cabin vibration blade failure, jamming of a flight control, and subsequent loss of control of the helicopter.
AD 2013-05-22 · published Mar 26, 2013, effective Apr 30, 2013
Agusta S.p.A. Helicopters
We are adopting a new airworthiness directive (AD) for all Agusta S.p.A. (Agusta) Model A109, A109A, A109A II, A109C, A109K2, A109E, A109S, and A119 helicopters. This AD was prompted by a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that a Model A109E helicopter experienced a failure of the tail rotor pitch control link assembly caused by a production defect. The actions of this AD are intended to prevent failure of a tail rotor pitch control link and subsequent loss of control of the helicopter.
AD 2013-05-01 · published Mar 6, 2013, effective Mar 21, 2013
Turbomeca S.A. Turboshaft Engines
We are superseding an existing airworthiness directive (AD) for all Turbomeca S.A. Makila 1A2 turboshaft engines. That AD currently requires replacement of certain serial number (S/N) N2 sensor harnesses. This AD requires replacement of the same S/N harnesses, and requires replacement of additional S/N N2 sensor harnesses. This AD was prompted by corrosion detected in affected N2 sensor harnesses. We are issuing this AD to prevent inadvertent activation of the 65% N1 back up mode, resulting in N2 speed fluctuation, significant power loss, and emergency landing of the helicopter.
AD 2013-05-13 · published Mar 20, 2013, effective Apr 24, 2013
Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) BR700-710 series turbofan engines. This AD requires replacement of the affected fuel pump splined couplings. This AD was prompted by service experience that demonstrated premature wear of the splined coupling on the fuel pump. We are issuing this AD to prevent failure of the engine and loss of the airplane.
AD 2013-05-19 · published Mar 20, 2013, effective Apr 24, 2013
Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Tay 611-8 turbofan engines. This AD requires inspection and replacement, if necessary, of affected bolts. This AD was prompted by a quality review determination that bolts with reduced material properties may have been installed in some engines. We are issuing this AD to prevent uncontained turbine disc fracture and damage to the airplane.
AD 2013-05-20 · published Mar 20, 2013, effective Apr 24, 2013
Rolls-Royce Deutschland Ltd & Co KG Turbojet Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Spey 511-8 turbojet engines. This AD requires inspection and, if necessary, replacement of affected bolts and, if any bolt is found broken, inspection of the adjacent disc(s) for damage. This AD was prompted by a recent quality review determination that bolts with reduced material properties may have been installed in some engines. We are issuing this AD to prevent uncontained turbine disc fracture and damage to the airplane.
AD 2013-06-01 · published Mar 20, 2013, effective Apr 24, 2013
Rolls-Royce Deutschland Ltd & Co KG Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) models Tay 620-15 and Tay 650-15 turbofan engines. This AD was prompted by RRD recalculating the Declared Safe Cyclic Life (DSCL) for certain low-pressure compressor (LPC) rotor disc assemblies operating to the Plan D Flight Mission. This AD requires removing the affected LPC rotor disc assemblies at a new lower recalculated DSCL. We are issuing this AD to prevent failure of the LPC rotor disc assembly, uncontained engine failure, and damage to the airplane.
AD 2013-05-18 · published Mar 21, 2013, effective Apr 5, 2013
Rolls-Royce plc Turbofan Engines
We are superseding an existing airworthiness directive (AD) for all Rolls-Royce plc (RR) RB211 Trent 500 series turbofan engines. That AD currently requires a one-time inspection of the fuel tubes and fuel tube clips for evidence of damage, wear, and fuel leakage. This AD requires the same inspection, and adds additional repetitive inspections. This AD was prompted by additional RR engineering analysis. We are issuing this AD to prevent engine fuel leaks, which could result in engine damage and damage to the airplane.
