34 Airworthiness Directives: 22 airplane, 6 rotorcraft, 6 engine.
AD 2013-06-05 · published Apr 4, 2013, effective May 9, 2013
The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. That AD currently requires repetitive inspections of the aft attach lugs of the elevator tab control mechanisms, and replacement of any discrepant elevator tab control mechanism. This new AD requires replacing the left and right elevator tab control mechanisms with elevator tab control mechanisms that have the modified attach lugs, which would terminate the existing requirements. This AD was prompted by reports of failure of the aft attach lugs on the elevator tab control mechanisms, which resulted in severe elevator vibration; and reports of gaps in elevator tab control mechanisms and analysis indicating that additional elevator tab control mechanisms might have bearings that will come loose. We are issuing this AD to prevent discrepancies in the aft attach lugs of the elevator tab control mechanism, which could result in severe elevator and tab vibration. Consequent structural failure of the elevator or horizontal stabilizer could result in loss of structural integrity and aircraft control.
AD 2013-04-04 · published Apr 10, 2013, effective May 15, 2013
The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for certain The Boeing Company Model 757 airplanes equipped with Rolls- Royce RB211-535E engines. That AD currently requires repetitive inspections for signs of damage of the aft hinge fittings and attachment bolts of the thrust reversers, and related investigative and corrective actions if necessary. The existing AD also provides for an optional terminating modification for the repetitive inspections. For certain airplanes, this new AD adds a one-time inspection of the washers installed under the attachment bolts of the aft hinge fittings for correct installation sequence, and reinstallation if necessary. This new AD also adds an option for installing a redesigned aft hinge fitting with the trim already done, instead of trimming an existing or new hinge fitting, which is included in the existing optional terminating modification. This AD was prompted by reports of incorrectly installed washers under the attachment bolts of the aft hinge fittings of the thrust reversers. We are issuing this AD to prevent failure of the attachment bolts and consequent separation of a thrust reverser from the airplane during flight, which could result in structural damage to the airplane.
AD 2013-07-02 · published Apr 10, 2013, effective May 15, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, and A320 series airplanes. This AD was prompted by fuel system reviews conducted by the manufacturer, which revealed that certain fuel pumps under certain conditions can create an ignition source in the fuel tank. This AD requires modification of the center tank fuel pump control circuit by installation of ground fault interrupters (GFIs). This AD would also require either replacement of the GFI or deactivation of the associated fuel pump following failure of any post-modification operational test of the GFI. We are issuing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2013-07-03 · published Apr 10, 2013, effective May 15, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200, A330-200 Freighter, A330-300, A340-200, and A340-300 series airplanes; and Model A340-541 airplanes and Model A340- 642 airplanes. This AD was prompted by reports of cracks in the bogie pivot pin caused by material heating due to friction between the bogie pivot pin and bush, leading to chrome detachment and chrome dragging on the bogie pivot pin. This AD requires repetitive detailed inspections for degradation of the bogie pivot pins and for any cracks and damage of the pivot pin bushes of the main and central landing gear; a magnetic particle inspection of the affected bogie pivot pins for corrosion and base metal cracks; and repairing or replacing bogie pivot pins and pivot pin bushes, if necessary. We are issuing this AD to detect and correct cracks and damage to the main and central landing gear, which could result in the collapse of the landing gear and adversely affect the airplane's continued safe flight and landing.
AD 2013-07-01 · published Apr 15, 2013, effective May 20, 2013
Diamond Aircraft Industries GmbH Airplanes
We are adopting a new airworthiness directive (AD) for Diamond Aircraft Industries GmbH Models DA 42, DA 42 M-NG, and DA 42NG airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as overextension of the main landing gear (MLG) shock absorber that could lead to the MLG jamming in the gear bay and result in damage to the aircraft or occupant injury. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-07-04 · published Apr 15, 2013, effective May 20, 2013
Airbus Airplanes
We are superseding an existing airworthiness directive (AD) for certain Airbus Model A319, A320, and A321 series airplanes. That AD currently requires installing spacer assemblies at the attachment points of the YZ-latches of the cargo loading system (CLS) in the forward and aft cargo compartments, as applicable. This new AD also requires modifying the attachment points of fixed YZ-latches of the CLS lower deck cargo holds on those airplanes on which one or both lower deck cargo holds have not been modified, which terminates the existing requirements. This AD was prompted by results from tests that have shown that the attachment points of the YZ-latches of the cargo loading system (CLS) fail under maximum loads and reports that installation has been applied only on one of the lower deck cargo holds, instead of on both forward and aft cargo holds, and that some airplanes could have installed the affected YZ-latches through the instructions of the cargo conversion manual. We are issuing this AD to prevent failure of the attachment points of the YZ-latches, which could result in unrestrained cargo causing damage to the fire protection system, hydraulic system, electrical wiring, or other equipment located in the forward and aft cargo compartments. This damage could adversely affect the continued safe flight of the airplane.
AD 2013-07-07 · published Apr 15, 2013, effective May 20, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by reports of an incorrect procedure used to apply the wear and corrosion protective surface coating to attach pins of the horizontal stabilizer rear spar. This AD requires inspecting to determine the part number of the attach pins of the horizontal stabilizer rear spar, and replacing certain attach pins with new, improved attach pins. We are issuing this AD to prevent premature failure of the attach pins, which could cause reduced structural integrity of the horizontal stabilizer to fuselage attachment, resulting in loss of control of the airplane.
AD 2013-07-08 · published Apr 15, 2013, effective May 20, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757 airplanes. This AD was prompted by reports that inspections of the wing center section revealed defective, misapplied, or missing secondary fuel vapor barriers on the center fuel tank. This AD requires inspecting for discrepancies and insufficient coverage of the secondary fuel barrier, determining the thickness of the secondary fuel barrier, and corrective actions if necessary. We are issuing this AD to detect and correct defective surfaces and insufficient thickness of the secondary fuel barrier, which could allow fuel leaks or fumes into the pressurized cabin, and allow fuel or fuel vapors to come in contact with an ignition source, which could result in a fire or an explosion.
AD 2013-07-09 · published Apr 15, 2013, effective May 20, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-700, -700C, -800, and -900ER series airplanes, Model 747-400F series airplanes, and Model 767-200 and -300 series airplanes. This AD was prompted by reports indicating that certain crew oxygen mask stowage box units were possibly delivered with a burr in the inlet fitting. The burr might break loose during test or operation, and might pose an ignition source or cause an inlet valve to jam. This final rule adds a step to identify and label certain crew oxygen mask stowage box units that have already been inspected and reworked by the supplier, and allows operators to install new or serviceable crew oxygen mask stowage box units, and requires a general visual inspection for affected serial numbers of the crew oxygen mask stowage box units, and replacement or re-identification as necessary. We are issuing this AD to prevent an ignition source, which could result in an oxygen-fed fire; or an inlet valve jam in a crew oxygen mask stowage box unit, which could result in restricted flow of oxygen.
AD 2013-07-11 · published Apr 15, 2013, effective May 20, 2013
The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. That AD currently requires inspecting for scribe lines in the skin along lap joints, butt joints, certain external doublers, and the large cargo door hinges, and doing related investigative and corrective actions if necessary. This new AD adds an inspection for scribe lines where external decals have been applied or removed across lap joints, large cargo door hinges, and external doublers, and related investigative and corrective actions if necessary. This AD was prompted by a determination that scribe lines could occur where external decals are installed or removed across lap joints, large cargo door hinges, or external doublers. We are issuing this AD to detect and correct scribe lines, which can develop into fatigue cracks in the skin. Undetected fatigue cracks can grow and cause sudden decompression of the airplane.
AD 2013-08-03 · published Apr 18, 2013, effective May 23, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200, A330-300, A340-200 and A340-300 series airplanes. This AD was prompted by a report that revealed the wheel axles of the main landing gear (MLG) were machined with a radius as small as 0.4 millimeters. This AD requires replacing the wheel axle of the MLG with a serviceable part. We are issuing this AD to prevent fatigue of the wheel axle of the MLG, which could adversely affect the structural integrity of the airplane.
AD 2013-08-04 · published Apr 18, 2013, effective May 23, 2013
Grob-Werke Airplanes
We are adopting a new airworthiness directive (AD) for Grob- Werke Model G115EG airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks in the elevator trim tab arms on several Grob G 115 airplanes, which could result in failure of the part and consequent loss of control. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-08-09 · published Apr 18, 2013, effective May 23, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300, -300ER, and 777F series airplanes. This AD was prompted by a report that during a test of the oxygen system, an operator found that the passenger oxygen masks did not properly flow oxygen, and that a loud noise occurred in the overhead area, which was caused by the flex line separating from the hard line due to a missing clamshell coupler. This AD requires, for certain airplanes, performing a detailed inspection of certain areas of the airplane oxygen system to ensure clamshell couplers are installed and fully latched, and corrective actions if necessary. For all airplanes, this AD requires performing and meeting the requirements of the low pressure leak test. We are issuing this AD to prevent the oxygen system flex line from separating from the hard line, which could cause an oxygen leak and a drop in the oxygen system pressure, resulting in improper flow of oxygen through the passenger masks and injury to passengers if emergency oxygen is needed.
AD 2013-07-13 · published Apr 19, 2013, effective May 6, 2013
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 7X airplanes. This AD requires revising the aircraft flight manual (AFM); performing operational tests of the oxygen mask oxygen assembly; and replacing affected stowage boxes, which terminates the AFM revision and operational tests. This AD was prompted by failure of the flight crew oxygen supply due to a potentially defective flight crew mask oxygen assembly. We are issuing this AD to prevent failure to supply oxygen upon demand to the flight crew in flight in "100%" and "Emergency" modes, which, in an emergency, may result in incapacitation of the flight crew.
AD 2013-08-02 · published Apr 19, 2013, effective May 24, 2013
The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) that applies to all The Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. That AD currently requires repetitive inspections for cracking of the elevator actuator fittings. This new AD requires, for previously modified airplanes, repetitive inspections for movement of the fittings or fastener heads, and eventual replacement of certain bolts (including related investigative and corrective actions if necessary). For all airplanes, this replacement, with corrected torque values, would terminate the requirements of the existing AD. This new AD also removes certain airplanes from the applicability. This AD was prompted by the manufacturer's development of a modification that was approved as an optional terminating action to the existing AD's required repetitive inspections. We have been advised that the modification procedures include certain incorrect torque values. We are issuing this AD to detect and correct a cracked actuator fitting or incorrectly installed bolts to the actuator fitting, which could lead to the elevator becoming detached and unrestrained, and a consequent unacceptable flutter condition and loss of control of the airplane.
AD 2013-08-08 · published Apr 19, 2013, effective May 24, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600 series airplanes. This AD was prompted by reports of early fatigue cracks at chem-mill areas on the crown skin panels. This AD requires repetitive inspections for cracking of the fuselage skin at certain locations at chem-mill areas, and repair if necessary. We are issuing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane.
AD 2013-08-23 · published Apr 24, 2013, effective May 29, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, MD-10-10F, MD-10-30F, MD-11, and MD-11F airplanes. This AD was prompted by fuel system reviews conducted by the manufacturer. This AD requires adding design features to detect electrical faults and to detect a pump running in an empty fuel tank. We are issuing this AD to reduce the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2013-08-05 · published Apr 25, 2013, effective May 30, 2013
Cessna Aircraft Company Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 525 airplanes equipped with certain part number (P/N) air conditioning (A/C) compressor motors. This AD was prompted by reports of smoke and/or fire in the tailcone caused by brushes wearing beyond their limits on the A/C motor. This AD requires inspection of the number of hours on the A/C compressor hour meter, inspection of the logbook, replacement of the brushes on certain P/N A/C compressor motors or deactivation of the A/C system until replacement of the brushes, and reporting of airplane information related to the replacement of the brushes. We are issuing this AD to correct the unsafe condition on these products.
AD 2013-08-10 · published Apr 25, 2013, effective May 10, 2013
Kelowna Flightcraft R & D Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for certain Tracor (Convair) Model 340 and 440 airplanes and certain Military Model C-131B, C-131D, C-131E, and C131F/R4Y-1 airplanes. This AD requires repetitive inspections of the lower skin of the wings for cracking around the inboard side of the wing station (WS) 6 and 7 access panel doubler fingers and between stringers 5 and 11; repetitive inspections of the lower skin of the wings for cracking around stringers 6, 8, and 10, and around the WS 6 and WS 7 access panel doubler fingers; and repair if necessary. This AD was prompted by a report of a crack found on the lower skin of the right-hand wing between WS 5 and WS 6. We are issuing this AD to detect and correct fatigue cracking of the lower skin of the wings, which could result in reduced structural integrity of the wings.
AD 2013-08-11 · published Apr 25, 2013, effective May 30, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-900 and -900ER series airplanes. This AD was prompted by reports of early fatigue cracks at chem-mill areas on the crown skin panels. This AD requires repetitive inspections for cracking of the fuselage skin along chem-mill steps at certain crown skin and shear wrinkle areas, and repair if necessary. We are issuing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane.
AD 2013-08-12 · published Apr 26, 2013, effective Apr 26, 2013
The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for The Boeing Company Model 787-8 airplanes. That AD currently requires modification of the battery system, or other actions. This AD requires installing main and auxiliary power unit (APU) battery enclosures and environmental control system (ECS) ducts; and replacing the main battery, APU battery, and their respective battery chargers. This AD also requires revising the maintenance program to include an airworthiness limitation. This AD also revises the applicability by removing airplanes on which these changes have been incorporated in production prior to delivery. This AD was prompted by recent incidents involving lithium ion battery failures that resulted in release of flammable electrolytes, heat damage, and smoke on two Model 787-8 airplanes. We are issuing this AD to minimize the occurrence of battery cell failures and propagation of such failures to other cells and to contain any flammable electrolytes, heat, and smoke released during a battery thermal event in order to prevent damage to critical systems and structures and the potential for fire in the electronics equipment bays.
AD 2004-21-08 R1 · published Apr 29, 2013, effective Apr 29, 2013
Cessna Aircraft Company Airplanes
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. That AD applies to all Cessna Aircraft Company (Cessna) Models 190, 195 (L-126A,B,C), 195A, and 195B airplanes that are equipped with certain inboard aileron hinge brackets. The AD docket number in the preamble section and the rule portion of the AD is incorrect. Also, the statement that no comments on the notice of proposed rulemaking (NPRM) were received is incorrect. This document corrects these errors. In all other respects, the original document remains the same.
AD 2013-06-07 · published Apr 4, 2013, effective May 9, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model SA-365N1, AS-365N2, and AS 365 N3 helicopters. This AD requires revising the Limitations section of the Rotorcraft Flight Manual (RFM) to prohibit flight in instrument meteorological conditions (IMC) or night visual flight rules (VFR) for each helicopter with a vertical gyro unit GV76-1 installed upon a non- reinforced shelf in the rear cargo compartment. Also, this AD requires modifying the GV76-1 vertical gyro unit shelf and testing for correct function of the navigation systems. This AD was prompted by flight crew reports of deviations between the displayed attitude on the attitude display screen and the independent electromechanical standby attitude indicator. The actions of this AD are intended to prevent an undetected flight display error of a slow drift in the roll axis, disorientation of the pilot, and subsequent loss of control of the helicopter.
AD 2013-07-05 · published Apr 10, 2013, effective May 15, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France EC130B4 helicopters. This AD requires visually checking the center windscreen panel (center windscreen) for a crack and replacing the center windscreen if there is a crack, if the windscreen distorts during flight, or within 12 months. This AD was prompted by in-flight cracking and failure of a center windscreen. The actions of this AD are intended to detect a crack in the blending radii of the center windscreen to prevent failure of the windscreen, injury to the flight crew, and subsequent loss of control of the helicopter.
AD 2013-08-06 · published Apr 18, 2013, effective May 23, 2013
Bell Helicopter Textron Canada (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 430 helicopters, which requires replacing certain components of the air data system. This AD was prompted by the discovery of incorrect indicated airspeed when the helicopter was tested to the cold temperature limits (-40 degrees centigrade) required for Category A operations. The actions of this AD are intended to correct the published Vne and to correct the indicated airspeed.
AD 2013-08-07 · published Apr 18, 2013, effective May 23, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (ECF) Model AS332C, L, and L1 helicopters to require an initial and repetitive inspections of the outer skin, butt strap, and fuselage frame for a crack and modification of the helicopter. This AD was prompted by an AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, which states that a crack was discovered in a fuselage frame during a daily check. The actions of this AD are intended to detect a crack, to prevent loss of airframe structural integrity and subsequent loss of control of the helicopter.
AD 2013-07-06 · published Apr 19, 2013, effective May 6, 2013
Eurocopter France Helicopters
We are adopting an airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS332C, AS332L, and AS332L1 helicopters and superseding an AD for Model AS332L2 and EC225LP helicopters. This AD requires inspecting the chip detector and modifying the chip collector, both installed on the main gearbox (MGB). This AD is prompted by an investigation which showed a failure within the epicyclic reduction gear module (epicyclic module) resulted in the rupture of the MGB case and separation of the main rotor head of a Model AS332L2 helicopter. These actions are intended to prevent failure of the MGB and subsequent loss of control of the helicopter.
AD 2012-25-04 · published Apr 24, 2013, effective May 9, 2013
Eurocopter France Helicopters
We are superseding an existing emergency airworthiness directive (EAD) for Eurocopter France (Eurocopter) Model AS350B3 helicopters with certain part-numbered laminated half-bearings (bearings) and tail rotor (T/R) blades installed. The existing EAD currently requires installing two placards and revising the Rotorcraft Flight Manual (RFM). The EAD also requires certain checks and inspecting and replacing, if necessary, all four bearings. Finally, the EAD requires a one-time removal and inspection of the bearings, and replacing the bearings if necessary. Since we issued that EAD, we have determined that newly-designed helicopters with other part-numbered T/R blades may be affected by this unsafe condition and that the requirements should allow the bearing removal and inspection to be performed before the last flight of the day. This superseding AD removes the bearing and T/R blade part numbers (P/N) from the applicability paragraph and clarifies when the bearing removal and inspection is required. The actions are intended to prevent vibration due to a failed bearing, failure of the T/R, and subsequent loss of control of the helicopter.
AD 2013-06-06 · published Apr 3, 2013, effective May 8, 2013
General Electric Company Turbofan Engines
We are adopting a new airworthiness directive (AD) for General Electric Company (GE) CF34-8C and CF34-8E turbofan engines with certain part numbers (P/N) of operability bleed valves (OBV) installed. This AD was prompted by three failure events of ring lock fuel fittings on the OBV. Two of those events led to an engine fire. This AD requires the affected OBVs be removed from service and replaced with OBVs eligible for installation. We are issuing this AD to prevent failure of OBV ring lock fuel fittings, engine fuel leakage, uncontrolled fire, and damage to the airplane.
AD 2013-05-04 · published Apr 15, 2013, effective Apr 30, 2013
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce plc (RR) RB211-Trent 970-84, RB211-Trent 970B-84, RB211- Trent 972-84, RB211-Trent 972B-84, RB211-Trent 977-84, RB211-Trent 977B-84, and RB211-Trent 980-84 turbofan engines. This AD requires inspection of the intermediate pressure compressor rear stub shaft (IPC RSS) piston ring. This AD was prompted by the failure of an oil pump drive shear neck due to a piston ring seal that was not seated properly in the IPC RSS groove. We are issuing this AD to prevent failure of the oil pump drive shear neck, which could result in loss of oil pressure in one or more engines and reduced control of the airplane.
AD 2013-07-10 · published Apr 15, 2013, effective May 20, 2013
International Aero Engines AG Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain International Aero Engines AG (IAE), V2525-D5 and V2528-D5 turbofan engines, with a certain No. 4 bearing internal scavenge tube and a certain No. 4 bearing external scavenge tube installed. This AD was prompted by a report of an engine under-cowl fire and commanded in- flight shutdown. This AD would require replacement of certain part number (P/N) No. 4 bearing internal scavenge tubes, and alignment checks of certain P/N No. 4 bearing external scavenge tubes. We are issuing this AD to prevent engine fire and damage to the airplane.
AD 2013-07-12 · published Apr 15, 2013, effective Apr 30, 2013
BRP-Powertrain GmbH & Co KG Rotax Reciprocating Engines
We are adopting a new airworthiness directive (AD) for certain BRP-Powertrain GmbH & Co KG Rotax 912 F2; 912 F3; 912 F4; 912 S2; 912 S3; 912 S4; 914 F2; 914 F3; and 914 F4 reciprocating engines. This AD requires a one-time visual inspection for excessive oil deposits or carbon deposits on the No. 2 and No. 3 spark plug center and grounding electrodes, and if found, replacement of the cylinder head before further flight. This AD was prompted by a report of certain No. 2 and No. 3 cylinder heads not manufactured to proper specification. We are issuing this AD to prevent excessive oil consumption, which could result in an in-flight engine shutdown, forced landing, and damage to the airplane.
AD 2013-08-22 · published Apr 23, 2013, effective May 28, 2013
Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 turboshaft engines. This AD requires daily post-flight checks of the engine tachometer's unit cycle-counting feature. This AD also requires ground-run functional checks within every 1,000 operating hours. This AD was prompted by detailed analysis and review of the accuracy of the engine's tachometer cycle-counting feature. We are issuing this AD to prevent uncontained engine failure and damage to the helicopter.
AD 2013-08-20 · published Apr 26, 2013, effective May 31, 2013
General Electric Company Turbofan Engines
We are superseding an existing airworthiness directive (AD) for certain General Electric Company (GE) CF6-80C2 series turbofan engines. That AD currently requires replacement of the fuel tube connecting the flowmeter to the integrated drive generator (IDG) fuel- oil cooler and the fuel tube(s) connecting the main engine control (MEC) or hydromechanical (HMU) to the flowmeter, with improved fuel tubes. This new AD requires the same actions, requires installation of a new simplified one-piece supporting bracket, adds an engine model, alters the list of affected part numbers (P/Ns), changes the replacement schedule, and revises our estimated cost of compliance. This AD was prompted by several additional reports of fuel leaks and two reports of engine fire due to improper assembly of supporting brackets on the fuel tube connecting the flowmeter to the IDG fuel-oil cooler. We are issuing this AD to prevent high-pressure fuel leaks caused by improper seating of fuel tube flanges, which could result in an engine fire and damage to the airplane.
