31 Airworthiness Directives: 18 airplane, 4 rotorcraft, 7 engine, 1 propeller, 1 various.
AD 2010-04-12 · published Mar 4, 2010, effective Apr 8, 2010
Bombardier, Inc. Model DHC-8-100 and DHC-8-200 Series Airplanes, and Model DHC-8-301, -311, and -315 Airplanes
We are adopting a new airworthiness directive (AD) for certain Model DHC-8-100 and DHC-8-200 series airplanes, and DHC-8-301, -311, and -315 airplanes. This AD requires implementing a corrosion prevention and control program (CPCP) either by accomplishing specific tasks or by revising the maintenance inspection program to include a CPCP. This AD results from the determination that, as airplanes age, they are more likely to exhibit indications of corrosion. We are issuing this AD to prevent structural failure of the airplane due to corrosion.
AD 2010-05-03 · published Mar 4, 2010, effective Apr 8, 2010
The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP Series Airplanes
We are adopting a new airworthiness directive (AD) for all Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This AD requires one-time detailed and high frequency eddy current inspections for cracks in the wing and horizontal stabilizer side-of-body joints and the fuselage skin circumferential splices, and repair if necessary. This AD also requires, for certain airplanes, repetitive detailed inspections for cracks of the fuselage skin circumferential splices, and repair if necessary. This AD results from Boeing analysis indicating that the wing and horizontal stabilizer side-of-body joints, and the fuselage skin circumferential splices, are susceptible to fatigue cracking due to high cyclic loads on the airplane. We are issuing this AD to detect and correct fatigue cracking at multiple adjacent locations in the subject areas, which could connect to form large cracks and result in reduced structural integrity leading to rapid decompression and consequent loss of control of the airplane.
AD 2010-05-10 · published Mar 4, 2010, effective Apr 8, 2010
Hawker Beechcraft Corporation (Type Certificate Previously Held by Raytheon Aircraft Company) Models B300 and B300C Airplanes
We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation (type certificate previously held by Raytheon Aircraft Company) Models B300 and B300C airplanes. This AD requires you to inspect the terminal board on the circuit card rack assembly to determine if the correct bus bar is installed and replace if necessary. This AD also requires you to do an operational check of the left and right pitot heat annunciators for proper operation and take corrective action as necessary. This AD results from reports of the left and right pitot heat annunciators not illuminating for an inoperative pitot heat condition. We are issuing this AD to detect and correct installation of an incorrect bus bar, which could result in failure of the pitot heat annunciators to illuminate. This failure could lead to the pilot being unaware that moisture has frozen on the pitot tube(s) and cause erroneous flight instrument indication.
AD 2010-05-11 · published Mar 9, 2010, effective Apr 13, 2010
The Boeing Company Model 747-100, 747-200B, 747-300, and 747SR Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 747-100, 747-200B, 747-300, and 747SR series airplanes. This AD requires installation of a closeout panel and moisture curtains for the main equipment center. This AD results from a report of water contamination in the electrical and electronic units in the main equipment center. We are issuing this AD to prevent the malfunction of one or more electrical and electronic units in the main equipment center, which could adversely affect the airplane's continued safe flight.
AD 2010-05-12 · published Mar 9, 2010, effective Apr 13, 2010
Bombardier Model DHC-8-102, DHC-8-103, DHC-8-106, DHC-8-201, and DHC-8-202 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-05-13 · published Mar 9, 2010, effective Apr 13, 2010
The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to all Model 737-100, -200, -200C, -300, -400, and - 500 series airplanes. That AD currently requires a one-time inspection for scribe lines and cracks in the fuselage skin at certain lap joints, butt joints, external repair doublers, and other areas; and related investigative/corrective actions if necessary. This new AD expands the area to be inspected and, for certain airplanes, requires earlier inspections for certain inspection zones. This AD results from additional detailed analysis of fuselage skin cracks adjacent to the skin lap joints on airplanes that had scribe lines. The analysis resulted in different inspection zones, thresholds and repetitive intervals, and airplane groupings. We are issuing this AD to prevent rapid decompression of the airplane due to fatigue cracks resulting from scribe lines on pressurized fuselage structure.
AD 2010-05-14 · published Mar 9, 2010, effective Mar 24, 2010
Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2009-22-05 · published Mar 11, 2010, effective Apr 15, 2010
Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-06-01 · published Mar 11, 2010, effective Apr 15, 2010
Airbus Model A319, A320, and A321 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-06-02 · published Mar 11, 2010, effective Apr 15, 2010
Hawker Beechcraft Corporation Model G58 Airplanes
We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation Model G58 airplanes. This AD requires inspecting the installation of stand-off hardware between the heater fuel line and the heater over-temperature sensor wires and also brake reservoir tubing and the heater fuel pump wiring for minimum clearance and installing acceptable stand-off hardware if stand-off hardware is missing or inadequate. This AD results from reports received of a power wire shorting out on the brake reservoir tube. We are issuing this AD to detect and correct inadequate clearance of the brake reservoir tubing and the heater fuel pump wiring, which could result in chafing and shorting out of the electrical wiring and chafing of the tubing carrying flammable fluids. This condition could lead to a fire in the nose wheel well.
AD 2010-06-04 · published Mar 11, 2010, effective Apr 15, 2010
Airbus Model A300 B2-1C, B2-203, B2K-3C, B4-103, B4-203, B4-2C Airplanes; Model A310 Series Airplanes; and Model A300 B4-601, B4-603, B4-605R, B4-620, B4-622, and B4-622R Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-06-05 · published Mar 11, 2010, effective Apr 15, 2010
Airbus Model A300 B4-2C, B4-103, and B4-203 Airplanes; and Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, and B4-622R Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-06-09 · published Mar 17, 2010, effective Apr 1, 2010
The Boeing Company Model 777-200, -200LR, -300, -300ER, and 777F Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 777-200, -200LR, -300, -300ER, and 777F series airplanes. This AD requires installing new operational program software for the autopilot flight director computers. This AD results from reports of rejected takeoffs at speeds above takeoff decision speed following inadvertent autopilot engagement on the ground, and from the discovery during flight simulations that the climb gradient is less than optimal for obstacle clearance during a performance-limited takeoff situation. We are issuing this AD to prevent inadvertent engagement of the autopilot during takeoff roll, which could result in rejected takeoff at rotation speed, and consequent possible overrun of the runway. We are also issuing this AD to prevent a lower-than-optimal climb gradient during takeoff, and consequent failure to clear obstacles on the ground during a performance-limited takeoff.
AD 2010-06-13 · published Mar 17, 2010, effective Apr 1, 2010
Learjet Inc. Model 45 Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 45 airplanes. This AD requires a general visual inspection for cracked and missing ballscrew assembly sleeves of the flap actuator, repetitive non-destructive liquid penetrant inspections of each sleeve or flap actuator for cracks, and replacement or modification of the flap actuator if necessary. This AD results from reports of cracked and missing ballscrew assembly sleeves of the flap actuators. We are issuing this AD to detect and correct cracked and missing sleeves, which could cause loss of the load-carrying ball bearings on both actuators on one flap, resulting in flap asymmetry and loss of control of the airplane.
AD 2010-06-16 · published Mar 17, 2010, effective Apr 21, 2010
The Boeing Company Model 767 Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 767 series airplanes. This AD requires inspections for scribe lines in the fuselage skin at skin lap joints, the skin at certain external approved repairs, the skin around external features such as antennas, and the skin at decals; and related investigative and corrective actions if necessary. This AD results from reports of scribe lines found at skin lap joints and butt joints, around external repairs and antennas, and at locations where external decals had been cut. We are issuing this AD to detect and correct scribe lines, which can develop into fatigue cracks in the skin and cause sudden decompression of the airplane.
AD 2010-07-04 · published Mar 25, 2010, effective Apr 9, 2010
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and Model ERJ 190 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-06-10 · published Mar 29, 2010, effective May 3, 2010
The Boeing Company Model 767-200, -300, and -300F Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 767-200, -300, and -300F series airplanes. For certain airplanes, this AD requires installing support hardware and modifying the interfacing wiring of the fuel quantity indicating system (FQIS) densitometer. For certain other airplanes, this AD requires replacing the existing hot short protector (HSP) on the FQIS densitometer with a new HSP. This AD also requires revising the Airworthiness Limitations (AWL) section of the Instructions for Continued Airworthiness to incorporate AWL No. 28-AWL-22. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent the center tank fuel densitometer from overheating and becoming a potential ignition source inside the center fuel tank, which, in combination with flammable fuel vapors, could result in a center fuel tank explosion and consequent loss of the airplane.
AD 2010-06-17 · published Mar 29, 2010, effective May 3, 2010
The Boeing Company Model 757 Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 757 airplanes. This AD requires inspecting to verify the part number of the low-pressure flex-hoses of the flightcrew and supernumerary oxygen system installed under the oxygen mask stowage box at a flightcrew and supernumerary oxygen mask location, and replacing with a new non-conductive low-pressure flex-hose of the oxygen system if necessary. This AD results from reports of a low-pressure flex-hose of a flightcrew oxygen system that burned through due to inadvertent electrical current from a short circuit in an adjacent audio select panel. We are issuing this AD to prevent inadvertent electrical current, which can cause the low-pressure flex-hose of a flightcrew or supernumerary oxygen system to melt or burn, resulting in oxygen system leakage and smoke or fire.
AD 2010-06-03 · published Mar 16, 2010, effective Apr 20, 2010
Eurocopter France Model AS355E, AS355F, AS355F1, AS355F2, and AS355N Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS355E, AS355F, AS355F1, AS355F2, and AS355N helicopters. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that a metallurgical non-conformity was discovered on a flange of the forward shaft section of the tail rotor drive shaft (drive shaft). The MCAI AD also states that stress analysis has shown that this non-conformity can significantly reduce the strength of the drive shaft and thereby its service life. The AD actions are intended to remove non-conforming drive shafts from service and prevent failure of the drive shaft and subsequent loss of control of the helicopter.
AD 2010-06-06 · published Mar 16, 2010, effective Apr 20, 2010
MD Helicopters, Inc. Model MD-900 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for MD Helicopters, Inc. (MDHI) model MD-900 helicopters that currently requires applying serial numbers to certain parts, increasing the life limit for various parts, maintaining a previously established life limit for a certain vertical stabilizer control system (VSCS) bellcrank assembly and bellcrank arm, and correcting the part number for the VSCS bellcrank arm. This amendment requires the same actions as the existing AD, except it reduces the life limit of the swashplate spherical slider bearing (slider bearing). It further corrects what was described as a "bellcrank arm" life limit in the current AD and correctly describes it as another "bellcrank assembly" life limit. This amendment is prompted by two reports of cracks in the slider bearing that occurred well before the previously increased retirement life of 2,030 hours time-in-service (TIS) was reached. The actions specified by this AD are intended to establish appropriate life limits for various parts, and to prevent fatigue failure of those parts and subsequent loss of control of the helicopter.
AD 2010-06-07 · published Mar 17, 2010, effective Apr 21, 2010
Eurocopter France Model AS 332 C, L, L1, and L2; AS 350 B3; AS355 F, F1, F2, and N; SA 365N and N1; AS 365 N2 and N3; SA 366G1; EC 130 B4; and EC 155B and B1 Helicopters
We are adopting a new airworthiness directive (AD) for the specified model helicopters. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that the AD is issued following a manufacturing nonconformity found on one batch of the servo-control caps. With a defective servo-control, rotation of the distributor might not be stopped mechanically since only friction of inner seals holds the distributor sleeve in its position. The AD actions are intended to address the unsafe condition created by a manufacturing nonconformity found on one batch of servo-control caps. If not corrected this condition could cause untimely movements of servo-controls, which are used on main and anti-torque rotors, and lead to the loss of control of the helicopter.
AD 2010-06-08 · published Mar 17, 2010, effective Apr 1, 2010
Sikorsky Aircraft Corporation Model S-76C Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Sikorsky Aircraft Corporation (Sikorsky) Model S-76C helicopters. This action requires inspecting the emergency flotation system squib connector (flotation system connector) to determine if a metallic foil shunt is installed. This amendment is prompted by a discovery that a metallic foil shunt meant to prevent inadvertent activation of a flotation system during installation was still installed in the left-hand flotation system connector of a Model S-76C helicopter. The actions specified in this AD are intended to determine if a metallic foil shunt is installed in the flotation system, which could prevent the flotation system from deploying and could prevent the helicopter from staying afloat long enough to enable emergency evacuation after a water landing.
AD 2010-06-12 · published Mar 16, 2010, effective Apr 20, 2010
Thielert Aircraft Engines GmbH (TAE) Models TAE 125-02-99 and TAE 125-01 Reciprocating Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-06-11 · published Mar 17, 2010, effective Apr 21, 2010
Honeywell International Inc. TFE731 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Honeywell International Inc. TFE731 series turbofan engines with certain second stage low-pressure compressor rotor (LPCR) discs and/or certain third stage LPCR discs installed. This AD requires removing from service certain second stage LPCR discs and/or certain third stage LPCR discs. This AD results from a report of cracks found during a fluorescent penetrant inspection (FPI) of the disc bore. We are issuing this AD to prevent an uncontained failure of a second stage LPCR disc and/or a third stage LPCR disc due to cracks in the bore, which could result in damage to the airplane.
AD 2010-06-15 · published Mar 17, 2010, effective Apr 1, 2010
General Electric Company CF6-45 and CF6-50 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF6-45 and CF6-50 series turbofan engines with certain low-pressure turbine (LPT) stage 3 disks installed. This AD requires fluorescent penetrant inspection (FPI) of the LPT stage 3 disk under certain conditions and removal of the disk from service before further flight if found cracked. This AD also requires initial and repetitive borescope inspections of the high-pressure turbine (HPT) rotor stage 1 and stage 2 blades for wear and damage, including excessive airfoil material loss. This AD results from three reports of uncontained failures of LPT stage 3 disks and eight reports of cracked LPT stage 3 disks found during shop visit inspections. We are issuing this AD to prevent critical life-limited rotating engine part failure, which could result in an uncontained engine failure and damage to the airplane.
AD 2010-06-18 · published Mar 18, 2010, effective Apr 22, 2010
International Aero Engines (IAE) V2500-A1, V2522-A5, V2524-A5, V2525-D5, V2527-A5, V2527E-A5, V2527M-A5, V2528-D5, V2530-A5, and V2533-A5 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for IAE V2500-A1, V2522-A5, V2524-A5, V2525-D5, V2527-A5, V2527E-A5, V2527M-A5, V2528-D5, V2530-A5, and V2533-A5 turbofan engines. This AD requires a onetime fluorescent penetrant inspection of certain vortex reducers for cracks. This AD results from reports of fractured vortex reducers found at shop visits. We are issuing this AD to inspect for cracks in the vortex reducer. Cracks in the vortex reducer could result in an uncontained failure of the high-pressure (HP) compressor stage 3-8 drum and subsequent damage to the airplane.
AD 97-17-04 R1 · published Mar 18, 2010, effective Apr 22, 2010
Pratt & Whitney Division Engines
The FAA is revising an existing airworthiness directive (AD) for Pratt & Whitney JT8D-209, -217, -217C, and -219 turbofan engines with front compressor front hub (fan hub), part number (P/N) 5000501-01 installed. That AD currently requires cleaning the front compressor front hubs (fan hubs), initial and repetitive eddy current (ECI) and fluorescent penetrant inspections (FPI) of tierod and counterweight holes for cracks, removal of bushings, cleaning and ECI and FPI of bushed holes for cracks and, if necessary, replacement with serviceable parts. In addition, that AD currently requires reporting the findings of cracked fan hubs and monthly reports of the number of inspections completed. This AD requires the same actions, except for the monthly reporting of the number of completed inspections. This AD results from the FAA determining that it has collected a sufficient amount of data since issuing AD 97-17-04 and that therefore, it no longer needs the monthly reporting of the number of completed inspections. We are issuing this AD to prevent fan hub failure due to tierod, counterweight, or bushed hole cracking, which could result in an uncontained engine failure and damage to the airplane. DATES: This AD becomes effective April 22, 2010. The Director of the Federal Register previously approved the incorporation by reference of the publications listed in the regulations as of March 5, 1997 (62 FR 4902).
AD 2010-06-14 · published Mar 29, 2010, effective May 3, 2010
Rolls-Royce plc RB211-Trent 800 Series Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-07-01 · published Mar 29, 2010, effective May 3, 2010
Rolls-Royce plc RB211-Trent 500, 700, and 800 Series Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product, and results from the risk of engine fuel-to-oil heat exchanger (FOHE) blockage. The MCAI describes the unsafe condition as:
AD 2010-05-09 · published Mar 3, 2010, effective Apr 7, 2010
Dowty Propellers Propellers
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: A number of propeller blade outer sleeves have been found with cracks since 1996. Testing has shown that blade retention integrity is not affected by this cracking. However, this condition, if not detected and corrected, can lead to blade counterweight release, possibly resulting in damage to the aircraft and injury to occupants or persons on the ground. We are issuing this AD to prevent blade counterweight release, which could result in injury or damage to the airplane.
AD 2010-07-02 · published Mar 29, 2010, effective May 3, 2010
Various Aircraft Equipped With Honeywell Primus II RNZ-850( )/-851( ) Integrated Navigation Units
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Honeywell Primus II RNZ-850( )/-851( ) integrated navigation units (INUs). As one alternative for compliance, the existing AD provides for a one-time inspection to determine whether a certain modification has been installed on the Honeywell Primus II NV-850 navigation receiver module (NRM), which is part of the INU. In lieu of accomplishing this inspection, and for aircraft found to have an affected NRM, that AD provides for revising the aircraft flight manual to include new limitations for instrument landing system approaches. That AD also requires an inspection to determine whether certain other modifications have been done on the NRM; and doing related investigative, corrective, and other specified actions, as applicable; as well as further modifications to address additional anomalies. This AD extends the compliance time for a certain inspection and associated actions. This AD also revises the applicability to include additional affected INUs. This AD results from reports indicating that erroneous localizer and glideslope indications have occurred on certain aircraft equipped with the subject INUs. We are issuing this AD to ensure that the flightcrew has accurate localizer and glideslope deviation indications. An erroneous localizer or glideslope deviation indication could lead to the aircraft making an approach off the localizer, which could result in impact with an obstacle or terrain.
