29 Airworthiness Directives: 21 airplane, 2 rotorcraft, 4 engine, 1 appliance, 1 glider.
AD 2010-06-51 · published Apr 2, 2010, effective Apr 7, 2010
The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes
This document publishes in the Federal Register an amendment adopting airworthiness directive (AD) 2010-06-51 that was sent previously to all known U.S. owners and operators of The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes by individual notices. This AD requires doing a detailed inspection of the inboard and outboard aft attach lugs of the left and right elevator control tab mechanisms for gaps between the swage ring and the aft attach lug, and between the spacer and the aft attach lug; trying to move or rotate the spacer using hand pressure; and replacing any discrepant elevator tab control mechanism, including performing the detailed inspection on the replacement part before and after installation. This AD is prompted by a report of failure of the aft attach lugs on the left elevator tab control mechanism, which resulted in severe elevator vibration. We are issuing this AD to detect and correct a loose bearing in the aft lug of the elevator tab control mechanism, which could result in unwanted elevator and tab vibration. The consequent structural failure of the elevator or horizontal stabilizer could result in loss of aircraft control and structural integrity.
AD 2010-07-03 · published Apr 2, 2010, effective May 7, 2010
The Boeing Company Model 747-200C and -200F Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Model 747-200C and -200F series airplanes. That AD currently requires repetitive inspections to find fatigue cracking in the floor panel attachment fastener holes of the upper chord of certain upper deck floor beams in Section 41 (i.e., body station 520 and forward), and repair if necessary. The existing AD also provides optional modifications, which extend the threshold for initiating certain repetitive inspections. This new AD requires additional repetitive inspections to find fatigue cracking in the floor panel attachment fastener holes of the upper chord of certain other upper deck floor beams in Section 41 and Section 42 (i.e., aft of body station 520); repetitive inspections to find fatigue cracking in the permanent fastener holes of the upper chord of certain upper deck floor beams in Section 41; and related investigative and corrective actions. This new AD also provides a new optional modification, which terminates certain repetitive inspections. This AD results from new reports of cracking in the upper chord of the upper deck floor beams in Sections 41 and 42, and new analysis that shows the permanent fastener holes of the upper chord of certain upper deck floor beams in Section 41 are also susceptible to fatigue cracking. We are issuing this AD to detect and correct cracking in the upper chord of the upper deck floor beams. Such cracking could extend and sever the floor beams, which could result in rapid decompression and loss of controllability of the airplane.
AD 2010-07-06 · published Apr 2, 2010, effective May 7, 2010
Bombardier, Inc. Model BD-100-1A10 (Challenger 300) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-07-07 · published Apr 2, 2010, effective May 7, 2010
SOCATA Model TBM 700 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-07-10 · published Apr 2, 2010, effective May 7, 2010
Airbus Model A300 B2-1C, B2K-3C, B2-203, B4-2C, B4-103, and B4-203 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-02 · published Apr 14, 2010, effective May 19, 2010
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ 190 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-03 · published Apr 14, 2010, effective May 19, 2010
Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-04 · published Apr 14, 2010, effective May 19, 2010
British Aerospace Regional Aircraft Model HP.137 Jetstream Mk.1, Jetstream Series 200, Jetstream Series 3101, and Jetstream Model 3201 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-05 · published Apr 14, 2010, effective May 19, 2010
Airbus Model A330-200, A330-300, and A340-300 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-06 · published Apr 14, 2010, effective May 19, 2010
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 Airplanes; and Model ERJ 190-100 STD, -100 LR, -100 IGW, -200 STD, -200 LR, and -200 IGW Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-07 · published Apr 14, 2010, effective Apr 29, 2010
Airbus Model 340-500 and -600 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-08-08 · published Apr 14, 2010, effective Apr 29, 2010
Airbus Model A330-243, -341, -342, and -343 Airplanes Equipped with Rolls-Royce Trent 700 Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2009-08-05 R1 · published Apr 19, 2010, effective Apr 19, 2010
Liberty Aerospace Incorporated Model XL-2 Airplanes
We are correcting the address, telephone, and fax information for the reporting requirement in Airworthiness Directive (AD) 2009-08- 05, which applies to certain Liberty Aerospace Incorporated Model XL-2 airplanes. AD 2009-08-05 currently requires repetitively inspecting the exhaust muffler for cracks, replacing the exhaust muffler when cracks are found, and reporting the results of the inspections to the FAA. Since AD 2009-08-05 became effective, the FAA's Atlanta Aircraft Certification Office (ACO) moved, which has caused the office personnel problems in receiving fax and mailed copies of the inspection result reports. This document corrects the mailing address, telephone number, and fax information of the Atlanta ACO.
AD 2010-09-05 · published Apr 26, 2010, effective Apr 29, 2010
The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. The existing AD currently requires doing a detailed inspection of the inboard and outboard aft attach lugs of the left and right elevator control tab mechanisms for gaps between the swage ring and the aft attach lug, and between the spacer and the aft attach lug; trying to move or rotate the spacer using hand pressure; and replacing any discrepant elevator tab control mechanism, including performing the detailed inspection on the replacement part before and after installation. For certain airplanes, this new AD adds improved repetitive inspections for discrepancies of the inboard and outboard aft attach lugs of the left and right elevator control tab mechanisms, and replacement if necessary. For certain other airplanes, this new AD adds a one-time inspection for discrepancies of the inboard and outboard aft attach lugs of the left and right elevator control tab mechanisms, and replacement if necessary. For airplanes on which the elevator control tab mechanism is replaced with a certain mechanism, this AD requires repetitive inspections for discrepancies of the elevator control tab mechanism and replacement if necessary. Replacing the elevator control tab mechanism with a new, Boeing-built mechanism terminates the repetitive inspections. This AD results from a report of failure of the aft attach lugs on the left elevator tab control mechanism, which resulted in severe elevator vibration; this event occurred on an airplane on which the existing AD had been done. We are issuing this AD to detect and correct a loose bearing in the aft lug of the elevator tab control mechanism, which could result in unwanted elevator and tab vibration. Consequent structural failure of the elevator or horizontal stabilizer could result in loss of structural integrity and aircraft control.
AD 2010-09-02 · published Apr 29, 2010, effective Jun 3, 2010
British Aerospace Regional Aircraft Model Jetstream Series 3101 and Jetstream Model 3201 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-09-03 · published Apr 29, 2010, effective May 14, 2010
The Boeing Company Model 747-200B Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 747-200B series airplanes. This AD requires repetitive inspections for cracking of the fuselage skin lap joints at stringer 6 on the left and right sides from station (STA) 340 to STA 400, a one- time general visual inspection to determine if certain fasteners are installed and to determine if service repair manual (SRM) repairs or repair doublers are installed, and corrective actions if necessary. Doing an optional modification of the stringer 6 lap joints terminates the repetitive inspections for the modified area. This AD results from reviews done by Boeing, which show that airplanes that were modified by Boeing to the stretched upper deck (SUD) configuration require inspection for cracking of the stringer 6 lap joint upper-fastener row earlier than previously expected. We are issuing this AD to detect and correct cracking of the stringer 6 lap joints where certain external doublers were not installed, which could result in rapid decompression and loss of structural integrity of the airplane.
AD 2010-09-04 · published Apr 29, 2010, effective May 14, 2010
Honeywell International Inc., Primus EPIC and Primus APEX Flight Management Systems, Installed on, but not Limited to, Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ 190 Airplanes, and Pilatus Aircraft Ltd. Model PC-12/47E Airplanes
We are adopting a new airworthiness directive (AD) for certain Honeywell International Inc., Primus EPIC and Primus APEX flight management systems (FMS), as installed on the airplanes described above. This AD requires revising the Limitations section of the airplane flight manual to incorporate the procedures necessary to recover from or work around a software anomaly in the FMS. This AD results from discovery of software anomalies which, in certain situations, can cause the FMS to generate misleading navigational guidance to the pilots and to the autopilot system of various airplanes having this same system software. We are issuing this AD to provide the flightcrew with procedures to recover from or work around these software anomalies during flight, which could lead to an airplane departing from its scheduled flight path, and result in possible collision with other aircraft or terrain.
AD 2010-09-06 · published Apr 29, 2010, effective Jun 3, 2010
Bombardier, Inc., Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-09-07 · published Apr 29, 2010, effective May 14, 2010
Bombardier, Inc. Model DHC-8-400 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-09-09 · published Apr 29, 2010, effective Jun 3, 2010
Piaggio Aero Industries S.p.A. Model PIAGGIO P-180 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-09-10 · published Apr 29, 2010, effective Jun 3, 2010
Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-05-51 · published Apr 29, 2010, effective May 14, 2010
Eurocopter France (ECF) Model EC120B Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010-05-51, which was sent previously to all known U.S. owners and operators of ECF Model EC120B helicopters by individual letters. This AD requires, at specified intervals, inspecting the main rotor head rotor hub (rotor hub) for a crack. If you find scoring, paint flaking or left-over identification plate adhesive, the AD requires sanding the area until the primer coat becomes visible and inspecting the rotor hub for a crack. If you find a crack, the AD requires, before further flight, replacing the rotor hub with an airworthy rotor hub. This amendment is prompted by a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that ECF has been informed of an emergency landing due to excessive vibrations originating from the main rotor. After an investigation, it was determined that the main rotor head rotor hub (rotor hub) had failed in the attachment area of one of the three drag damper fittings. The actions specified by the AD are intended to prevent failure of a hub, excessive vibrations, loss of a main rotor blade, and subsequent loss of control of the helicopter.
AD 2010-09-01 · published Apr 29, 2010, effective May 14, 2010
Eurocopter France Model AS350B, BA, B1, B2, B3, C, D, and D1; AS 355E, F, F1, F2, N, and NP Helicopters
We are adopting a new airworthiness directive (AD) for the specified Eurocopter France (Eurocopter) model helicopters. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD was issued following the discovery of a potential risk of an untimely squib firing that would cut the hoist cable. A short circuit in the hoist motor brush power supply wiring resulting in an uncommanded squib firing, which cuts the hoist cable, constitutes an unsafe condition.
AD 2009-08-08 R1 · published Apr 2, 2010, effective May 7, 2010
Turbomeca S.A. Engines
We are revising an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: During production of Arriel 1 and Arriel 2 Power Turbine (PT) wheels, geometric non-conformances on blade fir tree roots have been detected by Turbom ca. Potentially non-conforming PT blades have been traced as having been installed on Module M04 (PT) listed in Mandatory Service Bulletin (MSB) A292 72 0827 for Arriel 1 engines and A292 72 2833 for Arriel 2 engines. The geometric non-conformities of the blades may potentially lead to a reduction in the fatigue resistance of PT blades to a lower level than their authorized in service use limit. This reduction of fatigue resistance can potentially result in blade release, which could cause an uncommanded in-flight shutdown. We are issuing this AD to prevent release of PT blades, which could result in an uncommanded in-flight shutdown and emergency autorotation landing.
AD 2010-07-09 · published Apr 2, 2010, effective May 7, 2010
Rolls-Royce plc RB211-Trent 700 Series Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Rolls-Royce plc RB211-Trent 700 series turbofan engines. That AD currently requires initial and repetitive borescope inspections of the high-pressure-and-intermediate pressure (HP-IP) turbine internal and external oil vent tubes for coking and carbon buildup, and cleaning or replacing the vent tubes if necessary. This AD requires the same actions, but adds additional inspections of the vent flow restrictor. This AD results from further analysis that the cleaning of the vent tubes required by AD 2007-02-05 could lead to loosened carbon fragments, causing a blockage downstream in the vent flow restrictor. We are issuing this AD to prevent internal oil fires due to coking and carbon buildup that could cause uncontained engine failure and damage to the airplane.
AD 2010-09-08 · published Apr 23, 2010, effective May 28, 2010
General Electric Company (GE) CJ610 Series Turbojet Engines and CF700 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for GE CJ610 series turbojet engines and CF700 turbofan engines with AFT Technologies combustion liners, part number (P/N) AFT-5016T30G02. This AD requires removing from service, AFT Technologies combustion liners, P/N AFT-5016T30G02. This AD results from a report of an AFT Technologies combustion liner that released a large section of the inner combustion liner and reports of six combustion liners with premature cracks. We are issuing this AD to prevent premature cracks in the combustion liner, which could release pieces of the inner combustion liner. A release of pieces of the inner combustion liner could cause an uncontained failure of the engine turbine and damage to the airplane.
AD 2010-09-13 · published Apr 30, 2010, effective May 17, 2010
Turbomeca Makila 2A Turboshaft Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-07-08 · published Apr 2, 2010, effective Apr 19, 2010
Kelly Aerospace Energy Systems, LLC Rebuilt Turbochargers
The FAA is adopting a new airworthiness directive (AD) for certain Kelly Aerospace Energy Systems, LLC (KAES) rebuilt turbochargers. This AD requires removal from service of certain part number (P/N) and serial number (S/N) rebuilt turbochargers. This AD results from three reports of infant mortality turbine wheel failure in rebuilt turbochargers, since June of 2007. We are issuing this AD to prevent separation or seizure of the turbocharger turbine, which could result in full or partial engine power loss, loss of engine oil, and smoke in the airplane cabin.
AD 2010-08-01 · published Apr 6, 2010, effective Apr 26, 2010
Aircraft Industries a.s. Model L 23 Super Blanik Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
