29 Airworthiness Directives: 20 airplane, 5 engine, 1 appliance, 3 glider.
AD 2006-24-10 · published Dec 4, 2006, effective Jan 8, 2007
Air Tractor, Inc. Models AT-501, AT-502, AT-502A, AT-502B, and AT-503A Airplanes
We are adopting a new airworthiness directive (AD) for certain Air Tractor, Inc. Models AT-501, AT-502, AT-502A, AT-502B, and AT-503A airplanes, which supersedes AD 2002- 26-05 and AD 2002-11-05 R1. Since we issued AD 2002-26-05 and AD 2002- 11-05 R1, we determined that additional airplanes should be added to the applicability section and determined the safe life for new production airplanes and replacement spar caps should be extended. We also developed an alternative method of compliance (AMOC) to the requirements of this AD. This AD retains the actions required in AD 2002-26-05 and AD 2002-11-05 R1, adds additional airplanes to the Applicability section, extends the safe life for new production airplanes and replacement spar caps, and incorporates an AMOC. We are issuing this AD to prevent fatigue cracks from occurring in the wing lower spar cap before the established safe life is reached. Fatigue cracks in the wing lower spar cap could result in failure of the spar cap and lead to wing separation.
AD 2006-24-11 · published Dec 4, 2006, effective Dec 11, 2006
Raytheon Aircraft Company Models 1900, 1900C, and 1900D Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon Aircraft Company (RAC) Models 1900, 1900C, and 1900D airplanes. This AD requires you to repetitively inspect the forward, vertical, and aft flanges of both the left and right wing rear spar lower caps for cracks, repair any cracks found, and report the inspection results to RAC. This AD results from additional fatigue cracks found in this area since inspections were performed to comply with Emergency AD 2006-18-51, which required immediate visual inspections of this area. We are issuing this AD for the purpose of performing a more rigorous inspection requiring cleaning and paint stripping of this section of the wing rear spar to detect and correct cracking in the wing spar lower caps of the affected airplanes before the cracks lead to failure. These wing rear spar cracks may result in wing failure which could result in the wing separating from the airplane with consequent loss of control.
AD 2006-09-06 R1 · published Dec 7, 2006, effective Jun 7, 2006
Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-300, 747-400, 747-400D, and 747SR Series Airplanes
The FAA is revising an existing airworthiness directive (AD) that applies to certain Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-300, 747-400, 747-400D, and 747SR series airplanes. That AD currently requires repetitive inspections to detect cracking of certain lower lobe fuselage frames, and repair if necessary. This new AD specifies appropriate service information for certain corrective actions. This AD results from reports indicating that fatigue cracks were found in lower lobe frames on the left side of the fuselage. We are issuing this AD to detect and correct fatigue cracking of certain lower lobe fuselage frames, which could lead to fatigue cracks in the fuselage skin, and consequent rapid decompression of the airplane.
AD 2006-25-02 · published Dec 7, 2006, effective Jan 11, 2007
Gulfstream Model G-159 Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Gulfstream Model G-159 airplanes, that requires repetitive non-destructive testing inspections to detect corrosion of the skin of certain structural assemblies, and corrective action if necessary. This AD also requires x-ray and ultrasonic inspections to detect corrosion and cracking of the splicing of certain structural assemblies, and repair if necessary. The actions specified by this AD are intended to detect and correct corrosion and cracking of the lower wing plank splices and spot-welded skins of certain structural assemblies, which could result in reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
AD 2006-25-03 · published Dec 7, 2006, effective Jan 11, 2007
Airbus Model A300 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as failure of pitch trim system 2 to deflect the trimmable horizontal stabilizer at maximum rate, which could result in loss of high-speed trim and consequent reduced controllability of the airplane. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2006-25-04 · published Dec 7, 2006, effective Jan 11, 2007
Airbus Model A300 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Airbus Model A300 airplanes. That AD currently requires repetitive inspections for cracking and corrosion in the lower rim area of the rear pressure bulkhead and adjacent areas, repetitive inspections for cracking or corrosion in the service apertures and the upper rim area of the rear pressure bulkhead, and corrective actions if necessary. This new AD removes certain repetitive inspections and reduces the repetitive interval of one inspection. This new AD also requires an inspection for missing or damaged sealant in the area between the outer attachment angle and circumferential joint doubler, and corrective action if necessary. This new AD also requires additional inspections for corrosion of certain areas and repetitive inspections for airplanes on which repairs have been done. This AD results from reports of corrosion and cracking in the various components associated with the rear pressure bulkhead. We are issuing this AD to prevent reduced structural capability of the fuselage and consequent decompression of the airplane.
AD 2006-25-05 · published Dec 7, 2006, effective Jan 11, 2007
Boeing Model 777 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 777 airplanes. This AD requires repetitive inspections for corrosion or missing corrosion inhibiting compound of the fuselage skin under the forward and aft wing-to-body fairings for certain airplanes, or the fuselage skin under the forward wing-to-body fairings only for other airplanes; and corrective action if necessary. The AD also provides an optional preventive modification of the fairing areas, which terminates the repetitive inspections. This AD results from several reports indicating that significant levels of corrosion were found on the external surface of the fuselage skin under the forward and aft wing-to-body fairings. We are issuing this AD to detect and correct corrosion, and prevent subsequent fatigue cracks, on the fuselage skin under the forward and aft wing-to-body fairings, which could result in rapid decompression of the airplane.
AD 2006-25-06 · published Dec 11, 2006, effective Jan 16, 2007
Fokker Model F27 Mark 500 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F27 Mark 500 airplanes. This AD requires an inspection to determine whether certain main landing gear (MLG) drag stay units (DSUs) are installed. This AD also requires an ultrasonic inspection to determine if certain tubes are installed in the affected DSUs of the MLG, and related investigative/corrective actions if necessary. This AD results from a report that, due to fatigue cracking from an improperly machined radius of the inner tube, a drag stay broke, and, consequently, led to the collapse of the MLG during landing. We are issuing this AD to prevent such fatigue cracking, which could result in reduced structural integrity or collapse of the MLG.
AD 2006-25-07 · published Dec 11, 2006, effective Jan 16, 2007
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135ER and -135KE Airplanes; and Model EMB-145, -145ER, -145MR, -145MP, and -145EP Airplanes
The FAA is adopting a new airworthiness directive (AD) for all EMBRAER Model EMB-135ER and -135KE airplanes and Model EMB-145, -145ER, -145MR, -145MP, and -145EP airplanes. This AD requires inspecting the fuel quantity indication system (FQIS) wire harness and the direct current (DC) fuel pump wire harness to determine if the harnesses are properly attached at their respective attachment points and properly separated from one another, and performing corrective actions if necessary. This AD results from a report that the FQIS wire harness may not be properly attached at its attachment points or properly separated from the DC fuel pump wire harness. We are issuing this AD to prevent chafing between those harnesses or chafing of the harnesses against adjacent airplane structure or components, which could present a potential ignition source that could result in a fire or explosion.
AD 2006-25-08 · published Dec 11, 2006, effective Dec 21, 2006
Columbia Aircraft Manufacturing Models LC41-550FG and LC42-550FG Airplanes
The FAA is adopting a new Airworthiness Directive (AD) for all Columbia Aircraft Manufacturing (previously The Lancair Company) Models LC41-550FG and LC42-550FG airplanes equipped with Kelly Aerospace Thermal Systems Supplemental Type Certificate (STC) SA02260CH, Thermawing Deice System (also known as E-Vade). This AD requires you to deactivate the deice system and install a placard in clear view of the pilot. This AD results from problems with the installation of the Kelly Aerospace Thermal Systems Thermawing Deice System following STC SA02260CH. We are issuing this AD to prevent a short circuit condition at the deice heater connector, which could result in damage to the wings and horizontal stabilizer. This damage could lead to reduced structural integrity of the airplane.
AD 2006-25-09 · published Dec 12, 2006, effective Dec 27, 2006
McDonnell Douglas Model MD-11F Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model MD-11F airplanes. This AD requires a general visual inspection for installation of conduit and chafing damage on the auxiliary power unit (APU) power feeder wires and the upper surface of the auxiliary fuel tank and repair if necessary. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to detect and correct unprotected APU power feeder wires that come into close proximity to the upper surface of the auxiliary "piggy back" fuel tank, which could result in a potential ignition source, and in combination with flammable fuel vapors, could cause a fuel tank explosion and consequent loss of the airplane.
AD 2006-25-10 · published Dec 12, 2006, effective Jan 16, 2007
BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes
The FAA is adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ airplanes. This AD requires calculating the current life of each lift spoiler jack, and eventually replacing each lift spoiler jack. This AD results from a review of all system components as part of the life- extension program for the affected airplanes that indicated the fatigue life limit of certain lift spoiler jacks cannot be extended from the current life limit. We are issuing this AD to prevent failure of the lift spoiler jack, and consequent increased drag and uncommanded roll inputs, which could reduce the flightcrew's ability to control the airplane.
AD 2006-25-11 · published Dec 12, 2006, effective Jan 16, 2007
Lockheed Model L-1011 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Lockheed Model L-1011 series airplanes. This AD requires a one- time detailed inspection of the C112 harness clamp assembly for proper installation, a one-time detailed inspection of the C112 and C162 harness assemblies for damage, and corrective actions if necessary. This AD results from a report of electrical arcing of the essential bus feeder cables behind hinged circuit breaker panel CB3 P-K. We are issuing this AD to prevent arcing of essential bus feeder cables due to improper installation of the harness C112 clamp assembly, which could result in loss of electrical systems and smoke and/or fire behind the CB3 P-K hinged circuit breaker panel in the flight compartment.
AD 2006-25-16 · published Dec 15, 2006, effective Jan 19, 2007
Bombardier Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A and CL-601-3R) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Bombardier Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL- 600-2B16 (CL-601-3A and CL-601-3R) airplanes. This AD requires implementing a corrosion prevention and control program (CPCP) either by accomplishing specific tasks or by revising the maintenance inspection program to include a CPCP. This AD results from the determination that, as airplanes age, they are more likely to exhibit indications of corrosion. We are issuing this AD to prevent structural failure of the airplane due to corrosion.
AD 2006-25-17 · published Dec 15, 2006, effective Jan 19, 2007
Bombardier Model DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires repetitive cleaning/inspecting of the drain hole of each pitot static probe and repetitive cleaning of the pitot lines in the pitot static system. This AD results from reports of incidents of airspeed mismatch between the pilot, co-pilot, and standby airspeed indications caused by contamination in the pitot static system. We are issuing this AD to prevent erroneous/misleading altitude and airspeed information from a contaminated pitot static system to the flightcrew, which could reduce the ability of the flightcrew to maintain the safe flight and landing of the airplane.
AD 2006-26-03 · published Dec 26, 2006, effective Jan 30, 2007
Alpha Aviation Design Limited (Type Certificate No. A48EU formerly held by APEX Aircraft and AVIONS PIERRE ROBIN), Model R2160 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Alpha Aviation Model R2160 airplanes. This AD requires you to inspect the fuel pressure indication system for leakage at the end of the adapter in the fuel pressure indication system. This AD results from the possibility of fuel leakage at the end of the adapter in the fuel pressure indication system. We are issuing this AD to detect, correct, and prevent fuel leaks in the fuel pressure indicating system. This failure could allow fuel to leak near the exhaust manifold and lead to a fire.
AD 2006-26-04 · published Dec 27, 2006, effective Jan 31, 2007
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-145XR Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-145XR airplanes. This AD requires replacement of certain segments of the passenger seat tracks with new, improved seat tracks. This AD results from instances where the shear plungers of the passenger seat legs were not adequately fastened. We are issuing this AD to prevent inadequate fastening of the seat leg shear plungers, which could result in failure of the passenger seat tracks during emergency landing conditions and consequent injury to passengers.
AD 2006-26-05 · published Dec 27, 2006, effective Jan 31, 2007
Fokker Model F27 Mark 100, 200, 300, 400, 500, 600, and 700 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F27 Mark 100, 200, 300, 400, 500, 600, and 700 airplanes. This AD requires revising the Limitations section of the airplane flight manual regarding the use of continuous ignition, fuel filter heating, and resetting circuit breakers during flight in certain conditions such as icing. This AD results from reports of power loss on one or both engines in icing conditions. We are issuing this AD to advise the flightcrew that continuous ignition will not reduce the probability of power loss, and what action they must take to avoid this hazard. Loss of power in one or more engines during flight, if not prevented, could result in loss of control of the airplane.
AD 2006-26-06 · published Dec 27, 2006, effective Jan 11, 2007
Boeing Model 777-200 and -300 Series Airplanes Equipped with Rolls-Royce Engines
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 777-200 and -300 series airplanes equipped with Rolls-Royce engines. This AD requires repetitive inspections to detect cracks of the outer V-blades of the thrust reverser, and corrective action if necessary. This AD also provides for optional terminating action for the repetitive inspections. This AD results from reports of cracked outer V-blades in the thrust reversers. We are issuing this AD to prevent separation of a thrust reverser from the airplane during normal reverse thrust or during a refused takeoff, which could result in impact damage to other airplane areas. If a thrust reverser separates from the airplane during a refused takeoff, the engine could produce forward thrust, resulting in unexpected thrust asymmetry and a possible runway excursion.
AD 2006-26-08 · published Dec 28, 2006, effective Dec 28, 2006
Raytheon Aircraft Company Model 390 Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-02-51, which applies to certain Raytheon Aircraft Company Model 390 airplanes. AD 2006-02-51 currently requires you to inspect the left engine hydraulic pump outlet tube and the clamp; replace the clamp at each inspection; replace the hydraulic pump outlet tube immediately if any problem is found; and report the results of each inspection or replacement to the FAA. This AD is the result of several hydraulic pump outlet tube failures after issuance of AD 2006- 02-51, including failures on the right engine. This AD requires you to visually inspect the hydraulic pump outlet tube on both engines on a recurring basis and immediately replace the tube if damage is found. This AD also requires incorporation of an Airplane Flight Manual (AFM) change to not allow operation of an engine with its associated firewall hydraulic shutoff valve closed. In addition, this AD requires you to replace the hydraulic pump outlet tube if an engine is operated with its firewall hydraulic shutoff valve closed. We are issuing this AD to prevent failure of the hydraulic pump outlet tube and consequent leaking of hydraulic fluid. Such leakage could result in a fire. There is also a risk of loss of hydraulic system functions including normal gear extensions, speed brakes, roll spoilers, lift dump, and normal brakes.
AD 2006-24-08 · published Dec 4, 2006, effective Dec 19, 2006
Pratt & Whitney Canada (P&WC) PW535A Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as fuel manifold leakage that could result in engine fire, in-flight shutdown or damage to the airframe. This AD requires actions that are intended to address the unsafe condition described in the MCAI.
AD 2006-25-01 · published Dec 4, 2006, effective Jan 8, 2007
International Aero Engines AG (IAE) V2522-A5, V2524-A5, V2527-A5, V2527E-A5, V2527M-A5, V2530-A5, and V2533-A5 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for certain IAE V2522-A5, V2524-A5, V2527-A5, V2527E-A5, V2527M- A5, V2530-A5, and V2533-A5 turbofan engines. That AD currently requires initial and repetitive inspections of the master magnetic chip detector (MCD) or the No. 1, 2, 3 bearing chamber MCD. This AD requires the same MCD inspections. This AD also requires removing certain No. 3 bearings and removing certain high pressure compressure (HPC) stubshaft assemblies as mandatory terminating actions to the repetitive MCD inspections. This AD results from IAE developing a terminating action to the repetitive inspections of the chip detectors, and from expanding the applicability to include additional serial-numbered engines with certain No. 3 bearings installed. We are issuing this AD to prevent failure of the No. 3 bearing, which could result in an in-flight shutdown (IFSD) and smoke in the cockpit and cabin.
AD 2006-25-13 · published Dec 14, 2006, effective Dec 29, 2006
Rolls-Royce Corporation AE 2100D3 Turboprop Engines
The FAA is adopting a new airworthiness directive (AD) for Rolls-Royce Corporation (RRC) AE 2100D3 turboprop engines. This AD requires removing certain part number (P/N) compressor cone shaft assemblies at a new reduced cyclic life limit of 5,000 engine cycles. This AD results from low-cycle-fatigue testing and analysis of certain P/N compressor cone shaft assemblies, by RRC. We are issuing this AD to prevent uncontained failure of the compressor cone shaft assembly, leading to engine shutdown and damage to the airplane.
AD 2006-25-12 · published Dec 19, 2006, effective Jan 23, 2007
Rolls-Royce Corporation 501-D Series Turboprop Engines
The FAA is superseding an existing airworthiness directive (AD) for Rolls-Royce Corporation (RRC) 501-D series turboprop engines. That AD requires removal from service of certain turbine rotor components at reduced life limits. This AD requires the same actions but adds two new life limits. This AD results from RRC reevaluating and revising component life limits for 501-D22 series turboprop engines. We are issuing this AD to prevent uncontained turbine rotor failure resulting in an in-flight engine shutdown and possible damage to the airplane.
AD 2006-26-01 · published Dec 19, 2006, effective Jan 3, 2007
CFM International, S.A. CFM56 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International CFM56 Series turbofan engines. This AD requires replacing certain fuel filters manufactured under parts manufacturer approvals (PMA). This AD results from 12 reports of failed fuel filters. We are issuing this AD to prevent the loss of engine thrust that could result in loss of control during takeoff or landing.
AD 2006-25-15 · published Dec 15, 2006, effective Jan 19, 2007
Sicma Aero Seat; Third Occupant Seat Assemblies, 133 Series
The FAA is adopting a new airworthiness directive (AD) for Sicma Aero Seat third occupant seat assemblies, 133 series. This AD requires visually inspecting the installation of the two headrest bushings and installing Mecanindus pins to secure the bushings. This AD results from Sicma's determination that missing or incorrectly secured bushings could loosen and cause disengagement of the headrest from the seat during a high-energy stop of the airplane, possibly injuring the seat occupant. We are issuing this AD to prevent disengagement of the headrest from the seat during a high-energy stop of the airplane that could injure the seat occupant.
AD 2006-24-09 · published Dec 4, 2006, effective Jan 8, 2007
PZL-Bielsko Model SZD-50-3 “Puchacz” Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a discrepancy between the design documentation and the Technical Service Manual. In 1981, a castellated nut with cotter pin was introduced to secure the rudder, replacing the self-locking nut through PZL-Bielsko Bulletin No. BE-06/50-3/81. This change has not been introduced to the Technical Service Manual and use of a self-locking nut, in accordance with the Manual, is still possible. We are issuing this AD to require actions that are intended to address the unsafe condition described in the MCAI.
AD 2006-25-14 · published Dec 14, 2006, effective Jan 3, 2007
Schempp-Hirth Flugzeugbau GmbH Model Duo Discus T Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the possible failure of the attachment of the propeller blades. This AD requires actions that are intended to address the unsafe condition described in the MCAI.
AD 2006-26-02 · published Dec 21, 2006, effective Jan 10, 2007
Stemme GmbH & Co. KG Model S10, S10-V, and S10-VT Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
