28 Airworthiness Directives: 17 airplane, 3 rotorcraft, 7 engine, 1 various.
AD 2024-02-05 · published Mar 5, 2024, effective Apr 9, 2024
Bombardier, Inc., Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by a determination that a certain nondestructive test (NDT) procedure associated with a certain airworthiness limitation for inspecting the inboard, mid, and outboard flap metallic end ribs does not contain all of the necessary instructions. This AD requires a revision to the existing maintenance or inspection program to require using a revised NDT procedure when performing an airworthiness limitation task. This AD also prohibits the use of earlier revisions of that NDT procedure. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-02 · published Mar 5, 2024, effective Apr 9, 2024
MHI RJ Aviation ULC (Type Certificate Previously Held by Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all MHI RJ Aviation ULC (Type Certificate Previously Held by Bombardier, Inc.) Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600- 2C11 (Regional Jet Series 550), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-03 · published Mar 12, 2024, effective Apr 16, 2024
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by reports of corrosion on lavatory floor fittings at various locations. This AD requires repetitive general visual inspections of the affected parts, applicable corrective actions, and reporting of the inspection results, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-06 · published Mar 12, 2024, effective Apr 16, 2024
Bombardier, Inc., Airplanes
The FAA is superseding Airworthiness Directive (AD) 2021-20- 13, which applied to certain Bombardier, Inc., Model CL-600-2B16 (604 Variant) airplanes. AD 2021-20-13 required repetitive lubrication and repetitive detailed visual inspections (DVI) and non-destructive test (NDT) inspections of the main landing gear (MLG) shock strut lower pins, and replacement if necessary. This AD continues to require the lubrication and inspections specified in AD 2021-20-13 until the MLG shock strut assembly is modified by replacing the trailing arm bushing and installing new dynamic joint components. This AD was prompted by a new design solution for this potential failure of the shock strut lower pin. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-07 · published Mar 12, 2024, effective Apr 16, 2024
Deutsche Aircraft GmbH (Type Certificate Previously Held by 328 Support Services GmbH; AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftahrt GmbH) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Deutsche Aircraft GmbH Model 328-100 and 328-300 airplanes. This AD was prompted by operator reports of worn and ruptured bonding straps inside the feeder wing tanks and in both outer and inner wing tanks. This AD requires a one-time detailed inspection of each affected part, and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-09 · published Mar 12, 2024, effective Apr 16, 2024
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A11 airplanes. This AD was prompted by a manufacturing issue with an electrical connector that may prevent the connector from self-locking. This AD requires removing the affected connector, installing a new connector, and testing the emergency power supply units (EPSUs), as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-05-05 · published Mar 14, 2024, effective Mar 29, 2024
ATR-GIE Avions de Transport Régional Airplanes
The FAA is adopting a new airworthiness directive (AD) for all ATR-GIE Avions de Transport R[eacute]gional Model ATR42 and ATR72 airplanes. This AD was prompted by a report of incorrect marking and assembly of the two-way valves for the left- and right-hand engine fire extinguishing systems. This AD requires accomplishing a functional check of an affected part; replacing an affected part if necessary; reporting the functional check results; and prohibiting the installation of affected parts; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-03 · published Mar 15, 2024, effective Apr 19, 2024
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-04 · published Mar 18, 2024, effective Apr 22, 2024
Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2018-14- 09, which applied to certain Airbus SAS Model A318 series airplanes; Model A319 series airplanes; Model A320-211, -212, -214, -216, -231, - 232, and -233 airplanes; and Model A321-111, -112, -131, -211, -212, - 213, -231, and -232 airplanes. AD 2018-14-09 required repetitive inspections for cracking of the fastener holes in certain fuselage frames, and depending on airplane configuration, provides an optional terminating action to the repetitive inspections. This AD was prompted by reports of early cracking on the four holes of the crossbeam splicing at certain fuselage frames (FR). This AD continues to require the actions in AD 2018-14-09 at modified compliance times, requires further inspections, and provides optional terminating actions for certain airplanes; as specified in European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-06 · published Mar 18, 2024, effective Apr 22, 2024
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by reports of mechanical wear damage on the motive flow fuel-feed tubes that were secured by bonding clamps and clamp blocks inside the collector tank. This AD requires repetitive operational checks of the gravity cross flow shut-off valve and, for certain airplanes, a one-time inspection of the motive flow fuel-feed tubes at the clamp blocks location, and corrective action if necessary, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-07 · published Mar 18, 2024, effective Apr 22, 2024
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A318, A319, A320, and A321 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-08 · published Mar 19, 2024, effective Apr 23, 2024
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by a report of possible chafing of a power harness at fuselage frame (FR) 65. This AD requires rerouting the power harness, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-09 · published Mar 19, 2024, effective Apr 23, 2024
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, 777-200LR, 777-300, 777- 300ER, and 777F series airplanes. This AD was prompted by reports of wing anti-ice (WAI) valve failure that can result in undetected structural damage to leading edge (LE) slat assemblies, and separately a failure of the autothrottle (A/T) to disconnect after the pilot manually advanced the throttle levers, which caused a low-speed condition during a go-around. This AD was also prompted by a determination that insufficient low-speed protection exists in the 777 fleet and a determination that the flightcrew may not recognize and properly respond to a multi-channel unreliable airspeed event. This AD requires installing certain new software and doing a software configuration check. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-05-13 · published Mar 26, 2024, effective Apr 10, 2024
Embraer S.A. Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Embraer S.A. Model EMB-545 and EMB-550 airplanes. This AD was prompted by a report of a hard landing event with substantial damage to the airplane, in which the angle of attack (AOA) limiter was engaged during the final approach phase in unstable air conditions and remained engaged until the airplane touched down on the runway. This AD requires revising the Limitations and Normal Procedures sections of the existing airplane flight manual (AFM) to incorporate new operational airspeed limitations, and flight control limitations and approach procedures when AOA limiter protection is engaged, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. This AD also requires inspecting records for instances of AOA limiter engagement during a certain phase of flight and reporting findings to the FAA. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-11 · published Mar 27, 2024, effective May 1, 2024
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by damage found on two power- feeder harnesses on three airplanes due to chafing with wheel bins. An investigation found that the power-feeder harnesses were not adequately supported to protect from chafing due to vibration. This AD requires modifying the variable frequency generator (VFG) power-feeder harness routing, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-05-04 · published Mar 28, 2024, effective May 2, 2024
Gulfstream Aerospace Corporation Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-23- 04, which applied to certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII-G600 airplanes. AD 2020-23-04 required revising the existing airplane flight manual (AFM) and airplane maintenance manual (AMM) to include information pertaining to the fuel boost pump. This AD was prompted by a report of misassembled impellers on the shaft of the fuel boost pump during production. This AD retains the requirements of AD 2020-23-04 and requires inspecting affected fuel boost pumps for proper installation of the impeller shaft key, marking affected fuel boost pumps that pass that inspection, and replacing fuel boost pumps that fail. This AD also limits the installation of affected fuel boost pumps. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-08 · published Mar 29, 2024, effective May 3, 2024
Bombardier, Inc., Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports that some overheat detection sensing elements of the bleed air leak detection system were manufactured with insufficient salt fill, which can result in an inability to detect hot bleed air leaks. This AD requires maintenance records verification, and if an affected part is installed, would prohibit the use of certain Master Minimum Equipment List (MMEL) items under certain conditions by requiring revising the operator's existing Minimum Equipment List (MEL). This AD also requires testing the overheat detection sensing elements, marking each serviceable sensing element with a witness mark, and replacing each nonserviceable part with a serviceable part. This AD also prohibits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-10 · published Mar 4, 2024, effective Mar 19, 2024
Airbus Helicopters Deutschland GmbH (AHD) Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T2, EC135T3, and EC635T2+ helicopters. This AD was prompted by a report of a separated tail rotor (T/R) blade due to a crack which was caused by intergranular corrosion. This AD requires repetitively inspecting certain part- numbered T/R blades for a crack and, depending on the results, removing any cracked T/R blade from service. This AD also prohibits installing certain T/R blades on any helicopter unless certain requirements are met. These actions are specified in a European Union Aviation Safety Agency (EASA) emergency AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-01 · published Mar 15, 2024, effective Apr 19, 2024
Airbus Helicopters Deutschland GmbH (AHD) Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH (AHD) Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, MBB-BK 117 C-2, MBB-BK 117 D-2, and MBB-BK 117 D-3 helicopters. This AD was prompted by the determination that Instrument Flight Rules (IFR) screens obstruct the pilot's view. This AD requires removing certain part-numbered IFR screens, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-05 · published Mar 15, 2024, effective Apr 19, 2024
Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB412 and AB412 EP helicopters. This AD was prompted by reports of cracks in the lateral mounts of the main transmission support case. This AD requires repetitive visual inspections and fluorescent penetrant inspections (FPI) and, depending on the results, corrective action, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-05-01 · published Mar 5, 2024, effective Mar 11, 2024
Austro Engine GmbH Engines
The FAA is adopting a new airworthiness directive (AD) for certain Austro Engine GmbH Model E4 and E4P engines. This AD was prompted by reports of engine failures and the determination that certain batches of cap screws, installed on the inner main bearing positions of the engine, were manufactured at the lower end of the material strength tolerance. This AD requires replacing certain cap screws with a part eligible for installation and prohibits installing certain cap screws on any inner main bearing position of any engine. This AD also prohibits installing certain engine cores on any engine unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-03-05 · published Mar 13, 2024, effective Apr 17, 2024
GE Aviation Czech s.r.o. (Type Certificate Previously Held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Engines
The FAA is superseding Airworthiness Directive (AD) 2022-13-16 for all GE Aviation Czech s.r.o. (GEAC) (type certificate previously held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Model M601D-11 engines; and AD 2022-14-12, for certain GEAC Model M601D-11, M601E-11, M601E-11A, M601E-11AS, M601E-11S, and M601F engines. AD 2022- 13-16 required revising the airworthiness limitations section (ALS) of the existing engine maintenance manual (EMM) to incorporate a visual inspection of the centrifugal compressor case for cracks. AD 2022-14-12 required replacing the propeller shaft for Model M601F engines. AD 2022-14-12 also required calculating the accumulated life of the propeller shaft and replacing the propeller shaft, if necessary, for model M601D-11, M601E-11, M601E-11A, M601E-11AS, and M601E-11S engines. Since the FAA issued AD 2022-13-16 and AD 2022-14-12, the manufacturer revised the ALS of the existing EMM to introduce new and more restrictive tasks and limitations, expand the applicability to all Model M601 engines, and incorporate certain requirements addressed by AD 2021-13-07 and AD 2023-01-10, which prompted this AD. This AD requires revising the ALS of the existing EMM and the operator's existing approved engine maintenance or inspection program, as applicable, to incorporate new and more restrictive tasks and limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-04-51 · published Mar 13, 2024, effective Mar 28, 2024
Pratt & Whitney Canada Corp. Engines
The FAA is adopting a new airworthiness directive (AD) for all Pratt & Whitney Canada Corp. (P&WC) Model PT6A-64, PT6A-66, PT6A-66A, PT6A-66B, PT6A-66D, PT6A-67, PT6A-67A, PT6A-67AF, PT6A-67AG, PT6A-67B, PT6A-67D, PT6A-67F, PT6A-67P, PT6A-67R, PT6A-67RM, PT6A-67T, PT6A-68, PT6A-68D, PT6E-67XP, and PT6E-66XT engines. The FAA previously sent this AD as an emergency AD to all known U.S. owners and operators of these engines. This AD was prompted by reports of second-stage power turbine (PT2) blade failures. This AD requires removal of affected PT2 blades prior to the next flight and prohibits installation of affected PT2 blades, as specified in a Transport Canada Emergency AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-06-09 · published Mar 22, 2024, effective Mar 25, 2024
CFM International, S.A. Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model CFM56-2, CFM56-3, CFM56-5, CFM56-5B, CFM56-5C, and CFM56-7B engines. This AD was prompted by a report of electrical arcing on certain life-limited critical parts. This AD requires replacing certain compressor discharge pressure (CDP) seals, high-pressure compressor (HPC) stage 3 disks, and high-pressure turbine (HPT) rear shafts. This AD also prohibits installation of certain CDP seals, HPC stage 3 disks, and HPT rear shafts on any engine, and prohibits installation of any engine with certain CDP seals, HPC stage 3 disks, and HPT rear shafts installed on any airplane. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-05-11 · published Mar 27, 2024, effective Apr 11, 2024
International Aero Engines, LLC Engines
The FAA is superseding Airworthiness Directive (AD) 2022-19-15 for certain International Aero Engines, LLC (IAE LLC) Model PW1100G series engines; and AD 2023-16-07 for certain IAE LLC Model PW1100G series engines and PW1400G series engines. AD 2022-19-15 required an angled ultrasonic inspection (AUSI) of the high-pressure turbine (HPT) 1st-stage disk and HPT 2nd-stage disk, and replacement, if necessary. AD 2023-16-07 required an AUSI of the HPT 1st-stage hub (also known as the HPT 1st-stage disk) and HPT 2nd-stage hub (also known as the HPT 2nd-stage disk) for cracks, and replacement, if necessary, which is terminating action for AD 2022-19-15. This AD was prompted by an investigation that determined an increased risk of powdered metal anomalies for all powdered metal parts in certain powdered metal production campaigns, which are susceptible to failure significantly earlier than previously determined. This AD retains the AUSI requirement for certain HPT 1st-stage and HPT 2nd-stage hubs from AD 2023-16-07. This AD requires performing an AUSI of the HPT 1st-stage hub, HPT 2nd-stage hub, high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7), and HPC 8th-stage integrally bladed rotor (IBR-8) for cracks, and replacing if necessary. This AD also requires accelerated replacement of the HPC IBR-7, HPC IBR-8, HPC rear hub, HPT 1st-stage hub, and HPT 2nd-stage hub. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-06-02 · published Mar 27, 2024, effective Apr 11, 2024
GE Aviation Czech s.r.o. (Type Certificate Previously Held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Engines
The FAA is adopting a new airworthiness directive (AD) for all GE Aviation Czech s.r.o. (GEAC) (type certificate previously held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Model M601D-11, M601E-11, M601E-11A, M601E-11AS, M601E-11S, and M601F engines. This AD was prompted by a report of a crack on the centrifugal compressor case mount pad weld area, caused by a non-conforming welding (lack of welding penetration). This AD requires a one-time detailed visual inspection of the compressor case pad welds for any crack, and replacement of the compressor case if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-06-04 · published Mar 27, 2024, effective Apr 11, 2024
Pratt & Whitney Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain Pratt & Whitney (PW) Model PW1519G, PW1521G, PW1521GA, PW1521G- 3, PW1524G, PW1524G-3, PW1525G, PW1525G-3, PW1919G, PW1921G, PW1922G, PW1923G, and PW1923G-A engines. This AD was prompted by an updated analysis of an event involving an International Aero Engines, LLC (IAE LLC) Model PW1127GA-JM engine, which experienced a high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7) separation that resulted in an engine shutdown and aborted takeoff. This AD requires performing an angled ultrasonic inspection (AUSI) of certain high-pressure turbine (HPT) 1st-stage hubs, HPT 2nd-stage hubs, and HPC 8th-stage disks for cracks and, depending on the results of the inspections, replacing the HPT 1st-stage hubs, HPT 2nd-stage hubs, or HPC 8th-stage disks. This AD also requires accelerated replacement of certain HPC 7th-stage rotors, HPC 8th-stage disks, HPC rear hubs, HPT 1st-stage hubs, HPT 2nd-stage hubs, HPT 1st-stage air seals, HPT 2nd- stage air seals, HPT 1st-stage blade retaining plates, and HPT 2nd- stage blade retaining plates. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-05-51 · published Mar 15, 2024, effective Apr 1, 2024
General Electric Company Engines, and Various Restricted Category Rotorcraft
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model CT7-2E1, CT7-2F1, CT7-8A, CT7-8E, CT7-8F5 engines, and various restricted category helicopters with GE Model T700-GE-700,-701A, -701C, -701D/CC, -701D, -401, -401C, CT7-2D or CT7-2D1 engines installed. This AD was prompted by at least four reports of failures of the torque reference tube magnetic insert braze joint of the power turbine drive shaft assembly within the last several months. This AD requires a phase array ultrasonic inspection of the torque reference tube magnetic insert braze joint of the power turbine drive shaft assembly for inadequate braze coverage, and repair or replacement of the power turbine drive shaft assembly if necessary. The FAA previously sent an emergency AD to all known U.S. owners and operators of these engines and helicopters and is now issuing this AD to address the unsafe condition on these products.
