29 Airworthiness Directives: 18 airplane, 5 rotorcraft, 3 engine, 2 propeller, 1 various.
AD 2013-11-17 · published Jul 2, 2013, effective Aug 6, 2013
Embraer S.A. Airplanes
We are superseding airworthiness directive (AD) 2010-14-14 that applies to certain Embraer S.A. Model ERJ 170 and ERJ 190 airplanes. AD 2010-14-14 currently requires, for certain airplanes, repetitively replacing the low-stage check valve and associated seals of the right hand (RH) engine's engine bleed system with a new check valve and new seals, replacing the low pressure check valves (LPCVs), and revising the maintenance program. For certain other airplanes, AD 2010-14-14 requires replacing a certain low-stage check valve with an improved low-stage check valve. For certain airplanes, this new AD adds replacing certain LPCVs of the left hand (LH) and RH engines, which would be an option for other airplanes. This AD was prompted by reports of uncommanded engine shutdowns on both Model ERJ 170 and ERJ 190 airplanes due to excessive wear and failure of LPCVs having certain part numbers. We are issuing this AD to prevent the possibility of a dual engine in-flight shutdown due to LPCV failure.
AD 2013-13-09 · published Jul 2, 2013, effective Aug 6, 2013
Learjet Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Learjet Inc. Model 60 airplanes. This AD was prompted by a report of a high-speed rejected takeoff caused by all four main landing gear (MLG) tires blowing out during the takeoff roll. This AD requires installing new rigid hydraulic tube assemblies to the MLG struts; installing a new MLG squat switch bracket, modifying the MLG squat switch wire harness; modifying the MLG anti-skid wheel transducer electrical wire harnesses; routing and securing the anti-skid wheel and squat switch electrical wire harnesses to the MLG strut assembly; installing outboard bracket assemblies, anti-skid shield, forward electrical cover on the forward stiffener, upper and lower inboard bracket assemblies, and clamps that support the electrical wire harness; modifying the aft stiffener for the new electrical wire harness support; installing the aft electrical cover and strap on the aft stiffener; installing a new flat landing light lamp if necessary; and, for certain airplanes, installing a new wheel speed detect box assembly, nutplates, and brackets and a new thrust reverser interface box, and modifying the wiring for the new thrust reverser interface box. We are issuing this AD to prevent failure of the braking system or adverse operation of the spoiler and thrust reverser system due to external damage, particularly from tire failure, which could result in loss of control of the airplane.
AD 2013-13-11 · published Jul 2, 2013, effective Aug 6, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400, -400D, and -400F series airplanes. This AD was prompted by reports of two in-service occurrences on Model 737-400 airplanes of total loss of boost pump pressure of the fuel feed system, followed by loss of fuel system suction feed capability on one engine, and in-flight shutdown of the engine. This AD requires repetitive operational tests of the engine fuel suction feed of the fuel system, and other related testing and corrective actions if necessary. We are issuing this AD to detect and correct loss of the engine fuel suction feed capability of the fuel system, which, in the event of total loss of the fuel boost pumps, could result in multi- engine flameout, inability to restart the engines, and consequent forced landing of the airplane.
AD 2013-09-03 · published Jul 10, 2013, effective Aug 14, 2013
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain DASSAULT AVIATION Model FALCON 2000, FALCON 2000EX, MYSTERE-FALCON 900, and FALCON 900EX airplanes; and all Model MYSTERE-FALCON 50 airplanes. This AD was prompted by reports that collapse of the main landing gear (MLG) could cause wing tank structure failure, which could result in fuel spillage and consequent fire hazard. This AD requires modification of the wing fuel tanks in the area of the wheel well. We are issuing this AD to prevent fuel spillage in the event of a MLG collapse, and consequent fire hazard.
AD 2013-13-01 · published Jul 10, 2013, effective Jul 10, 2013
Piper Aircraft, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Piper Aircraft, Inc. Models PA-46-310P, PA-46-350P, PA-46R-350T, and PA-46-500TP airplanes. This AD requires inspecting the fuel vent valves to identify if the nitrile parts are installed and modifying and eventually replacing the fuel vent valves if the nitrile parts are installed. This AD was prompted by nitrile fuel vent valves not providing the correct ventilation. If not corrected, this unsafe condition may lead to structural damage of the wings, which could result in loss of control. We are issuing this AD to correct the unsafe condition on these products.
AD 2013-13-03 · published Jul 10, 2013, effective Aug 14, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A319-112, -113, and -132 airplanes; Model A320-211, -212, -214, -231, and -232 airplanes; and Model A321-111 and -131 airplanes. This AD was prompted by a report of two fatigue cracks on the left-hand and right-hand sides of the continuity fittings at the front windshield lower framing on a Model A319 series airplane. This AD requires a high frequency eddy current (HFEC) inspection for any cracking on the left- hand and right-hand sides of the windshield central lower node continuity fittings, and repair if necessary. We are issuing this AD to detect and correct cracking of the windshield central lower node continuity fittings, which could reduce the structural integrity of the airplane.
AD 2013-13-04 · published Jul 10, 2013, effective Aug 14, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by a report of an uncommanded nose landing gear (NLG) retraction. This AD requires installing a power interruption protection circuit for the landing gear control interface unit (LGCIU). We are issuing this AD to prevent untimely unlocking and/or retraction of the NLG, which, while on the ground, could result in injury to ground personnel and damage to the airplane.
AD 2013-13-10 · published Jul 10, 2013, effective Aug 14, 2013
Pilatus Aircraft Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for all PILATUS Aircraft Ltd. Model PC-7 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a need to incorporate new revisions into the Limitations section of the FAA-approved maintenance program (e.g., maintenance manual). The limitations were revised to include an emergency fuel control system adjustment test. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-13-08 · published Jul 16, 2013, effective Aug 20, 2013
The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for certain The Boeing Company Model 767 airplanes. That AD currently requires sealing certain fasteners and stiffeners in the fuel tank, changing certain wire bundle clamp configurations on the fuel tank walls, inspecting certain fasteners in the fuel tanks and determining the method of attachment of the vortex generators; and performing corrective actions if necessary. This new AD adds a general visual inspection for the presence of a polytetrafluoroethylene (TFE) sleeve at the clamp location on the rear spar, and installation of a TFE sleeve if necessary. This new AD also adds airplanes to the applicability. This AD was prompted by fuel system reviews conducted by the manufacturer, and the identification of another possible ignition source location. We are issuing this AD to prevent possible ignition sources in the auxiliary (center) fuel tank, main fuel tanks, and surge tanks caused by a wiring short or lightning strike, which could result in fuel tank explosions and consequent loss of the airplane.
AD 2013-13-15 · published Jul 16, 2013, effective Aug 20, 2013
the Boeing Company Airplanes
We are superseding airworthiness directive (AD) 87-02-07, which applied to all The Boeing Company Model 737-100 and -200 series airplanes. AD 87-02-07 required replacement of certain underwing fuel tank access covers with stronger, fire-resistant covers. This new AD also requires inspecting fuel tank access doors to determine that impact-resistant access doors are installed in the correct locations, inspecting application of stencils and index markers of impact- resistant access doors, doing corrective actions if necessary, revising the maintenance program, and adding airplanes to the applicability. This AD was prompted by reports of standard access doors installed where impact-resistant access doors are required, and reports of impact-resistant doors without stencils. We are issuing this AD to prevent foreign object penetration of the wing tank, which could lead to a fuel leak near ignition sources (engine, hot brakes), consequently leading to a fuel-fed fire.
AD 2013-14-01 · published Jul 16, 2013, effective Aug 5, 2013
Pilatus Aircraft Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for certain Pilatus Aircraft Ltd. Model PC-6/B2-H4 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as faulty rivets installed in the airframes during production could reduce the structural integrity of the airplane. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-13-17 · published Jul 22, 2013, effective Aug 26, 2013
Bombardier, Inc. Airplanes
We are superseding airworthiness directive (AD) 2011-13-08 for certain Bombardier, Inc. Model DHC-8-400 series airplanes. AD 2011-13- 08 required a free-play check for excessive free-play of the shaft swaged bearing installed in the tailstock end of each elevator power control unit (PCU), and replacing any PCU on which the bearing exceeds allowable limits with a serviceable PCU. This new AD adds airplanes to the applicability from that of AD 2011-13-08. This AD was prompted by a determination that additional airplanes are affected by the identified unsafe condition. We are issuing this AD to detect and correct excessive free-play of the swaged bearings, which could lead to excessive airframe vibrations and difficulties in pitch control, and consequent loss of controllability of the airplane.
AD 2013-14-02 · published Jul 22, 2013, effective Aug 26, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 727 airplanes. This AD was prompted by reports of spanwise cracks and corrosion in the wing center box upper skin and rear spar upper chord between left buttock line (LBL) 70.50 and right buttock line (RBL) 70.50 at body station (STA) 870. This AD requires repetitive inspections of the wing center box for cracking around certain fastener rows on the rear spar upper chord horizontal flange; for certain airplanes, repetitive inspections for cracking of the rear spar upper chord radius; for certain other airplanes, repetitive inspections for damage, cracking, and corrosion of the pressure seal; and repair if necessary. We are issuing this AD to detect and correct cracking and corrosion of the upper skin and rear spar upper chord of the wing center box, which could result in loss of the airplane wing and consequent loss of control of the airplane.
AD 2013-14-03 · published Jul 22, 2013, effective Aug 26, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 727 airplanes. This AD was prompted by reports of cracks on the elevator rear spar stiffener assembly. This AD requires repetitive detailed inspections for cracking of the elevator rear spar stiffener assembly, and corrective actions if necessary. We are issuing this AD to detect and correct cracking of the elevator rear spar stiffener assembly, which could adversely affect elevator structural stiffness, which could lead to elevator vibration and possible interference with the tab control rod. These conditions could result in flutter and consequent loss of control of the airplane.
AD 2013-14-05 · published Jul 22, 2013, effective Aug 26, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400 and 747-400F series airplanes. This AD was prompted by reports of cracking in the outboard flange of the longeron extension fittings, which attach to the wing-to-body fairing support frame. This AD requires repetitive inspections of the longeron extension fittings for cracking, and corrective actions if necessary. We are issuing this AD to detect and correct cracks in the longeron extension fittings, which can become large and adversely affect the structural integrity of the airplane.
AD 2013-14-07 · published Jul 22, 2013, effective Aug 26, 2013
Learjet Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Learjet Inc. Model 45 airplanes. This AD was prompted by a report that the fire barrier seal on the external baggage door does not seal the surrounding door structure due to incorrect positioning of the barrier. This AD requires modifying the fire seal on the baggage door, including doing inspections of the fire seal for correct contact and corrective action if necessary. We are issuing this AD to prevent improper sealing of the baggage door, which could increase the risk of an uncontained fire in the baggage compartment.
AD 2013-14-11 · published Jul 25, 2013, effective Aug 9, 2013
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for all Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440), CL- 600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD requires revising the airplane flight manual (AFM) by incorporating an emergency procedure for uncommanded yaw motion. This AD was prompted by reports of airplanes experiencing uncommanded rudder movements while in flight. We are issuing this AD to advise the flightcrew of procedures to address a possible failure of the voltage regulator inside the yaw damper actuator that could lead to uncommanded yaw movement and consequent loss of the ability to control the airplane.
AD 2013-15-07 · published Jul 26, 2013, effective Jul 26, 2013
the Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This AD requires either removal or inspection of the Honeywell fixed emergency locator transmitter (ELT), and corrective action if necessary. This AD was prompted by a report of a fire involving a Honeywell fixed ELT. We are issuing this AD to prevent a fire in the aft crown of the airplane, or to detect and correct discrepancies within the ELT that could cause such a fire.
AD 2013-12-06 · published Jul 9, 2013, effective Jul 24, 2013
Eurocopter Deutschland (Eurocopter) Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Model MBB-BK117 A-3, MBB-BK117 A-4, MBB-BK117 B-1, and MBB- BK117 C-2 helicopters with a Metro Aviation (Metro) vapor-cycle air conditioning kit installed in accordance with Supplemental Type Certificate (STC) No. SH3880SW. This AD requires repetitively inspecting the air conditioning drive pulley (pulley) for looseness and properly installed lockwire, and also requires reinstalling the pulley. This AD is prompted by two reports of the pulley detaching from the rotor brake disc on the tail rotor (T/R) driveshaft. These actions are intended to prevent separation of the pulley, damage to the T/R driveshaft, and subsequent loss of control of the helicopter.
AD 2013-10-51 · published Jul 16, 2013, effective Jul 31, 2013
Eurocopter France Helicopters
We are publishing a new airworthiness directive (AD) for Eurocopter France Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters. This AD requires, before further flight, determining whether a single hydraulic main or tail rotor servo-control is installed on your helicopter. If a certain servo-control is installed, before the further flight, this AD requires replacing that servo-control. This AD was prompted by the discovery of excessive axial play detected on bearings installed on certain single hydraulic main and tail rotor servo-controls (servo-control). The excessive play could cause the distributor slide valve to jam in its sleeve. This condition could result in jamming the hydraulic flight controls, necessitating that the pilot cut off hydraulic power. This action would increase the pilot's workload, resulting in possible loss of helicopter control.
AD 2013-12-05 · published Jul 16, 2013, effective Aug 20, 2013
Eurocopter Deutschland GmbH Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland GmbH (Eurocopter) Model MBB-BK 117 C-2 helicopters. This AD requires determining if a certain serial-numbered bevel gear is installed in the tailrotor intermediate gear box (IGB). If such a bevel gear is installed in the IGB, this AD requires recording the bevel gear's reduced life limit in the Airworthiness Limitations section of the maintenance manual and on the component history card or equivalent IGB record. If the bevel gear's life limit has been reached or exceeded, this AD requires, before further flight, replacing the bevel gear with an airworthy bevel gear. This AD is prompted by the discovery that the tooth foot fillets in certain bevel gears fall below the minimum dimensions required in the design documents to ensure safe functioning of the bevel gear until it reaches its approved life limit. This AD's actions are intended to prevent failure of a bevel gear before it reaches its currently approved life limit, failure of the IGB, and subsequent loss of helicopter control.
AD 2013-15-03 · published Jul 24, 2013, effective Aug 8, 2013
Eurocopter France (Eurocopter) Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, and AS350D1 helicopters with a single hydraulic system and a certain hydraulic pump drive installed. This AD requires inspecting the hydraulic pump drive pulley bearing (pulley bearing) for leaks, rust, overheating, and condition. This AD is prompted by six reports of hydraulic pump drive belt failure caused by seizure of the pulley bearing. These actions are intended to prevent hydraulic pump drive belt failure, loss of hydraulic servo assistance, and subsequent loss of control of the helicopter.
AD 2013-15-02 · published Jul 30, 2013, effective Aug 14, 2013
Bell Helicopter Textron Helicopters
We are superseding Airworthiness Directive (AD) 2008-10-03 for Bell Helicopter Textron Helicopters (Bell) Model 204B, 205A, 205A-1, 205B, 210, 212, 412, 412CF, and 412EP helicopters. AD 2008-10-03 required certain checks and inspections of each tail rotor blade assembly (T/R blade) at specified intervals and repairing or replacing, as applicable, any cracked or damaged T/R blade. Since we issued AD 2008-10-03, an accident attributed to a T/R failure occurred. This new AD retains the requirements of AD 2008-10-03 and adds a second, more detailed inspection that allows for an earlier detection of a crack or other damage in a T/R blade. These actions are intended to prevent a failure of the T/R blade and subsequent loss of helicopter control.
AD 2013-14-51 · published Jul 12, 2013
General Electric Company Engines
AD 2013-14-08 · published Jul 17, 2013, effective Aug 21, 2013
Austro Engine GmbH Engines
We are adopting a new airworthiness directive (AD) for all Austro Engine GmbH model E4 engines. This AD requires removing from service certain part number waste gate controllers. This AD was prompted by several reports of power loss events due to fracture of the waste gate controller lever. We are issuing this AD to prevent engine power loss or in-flight shutdown, which could result in loss of control and damage to the airplane.
AD 2013-14-06 · published Jul 30, 2013, effective Sep 3, 2013
CFM International, S. A. Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain CFM International, S. A. (CFM) model CFM56-5 and CFM56-5B series turbofan engines. This AD was prompted by corrosion of the delta-P valve in the hydro-mechanical unit (HMU) fuel control caused by exposure to type TS-1 fuel. This AD requires cleaning, inspection, and repair of affected HMUs. We are issuing this AD to prevent seizure of the HMU, leading to failure of one or more engines and damage to the airplane.
AD 2010-17-11 R1 · published Jul 10, 2013, effective Aug 14, 2013
Dowty Propellers Propellers
We are revising an existing airworthiness directive (AD) that applies to all Dowty Propellers R408/6-123-F/17 model propellers. That AD currently requires initial applications of sealant between the bus bar assembly and the backplate assembly of certain line-replaceable units, and repetitive applications of sealant on all R408/6-123-F/17 model propellers. This new AD requires the same actions and allows the use of an equivalent sealant as prescribed in revised service information. This AD was prompted by the need to add an optional terminating action to the applications of sealant. We are issuing this AD to prevent an in-flight double generator failure, which could result in reduced control of the airplane.
AD 2013-15-04 · published Jul 26, 2013, effective Aug 30, 2013
Hartzell Propeller, Inc. Propellers
We are adopting a new airworthiness directive (AD) for certain Hartzell Propeller, Inc. propeller models HC-(1,D)2(X,V,MV)20-7, HC- (1,D)2(X,V,MV)20-8, and HC-(1,D)3(X,V,MV)20-8. This AD was prompted by failures of the propeller hydraulic bladder diaphragm and resulting engine oil leak. This AD requires replacement of the propeller hydraulic bladder diaphragm. We are issuing this AD to prevent propeller hydraulic bladder diaphragm rupture, loss of engine oil, damage to the engine, and loss of the airplane.
AD 2013-13-14 · published Jul 9, 2013, effective Jul 24, 2013
Various Restricted Category Helicopters
We are adopting a new airworthiness directive (AD) for various restricted category Model HH-1K, TH-1F, TH-1L, UH-1A, UH-1B, UH-1E, UH- 1F, UH-1H, UH-1L, and UH-1P helicopters with certain main rotor hub inboard strap fittings (fittings) installed. This AD requires a magnetic particle inspection (MPI) of the fittings for a crack, and if there is a crack, replacing the fitting with an airworthy fitting. This AD is prompted by reports of cracked fittings on Bell model helicopters and the determination that these same part-numbered fittings may be installed on various restricted category helicopters. These actions are intended to detect a crack in a fitting, which may lead to failure of a fitting, loss of a main rotor blade, and subsequent loss of helicopter control.
