26 Airworthiness Directives: 16 airplane, 4 rotorcraft, 5 engine, 1 various.
AD 2013-11-01 · published Jun 4, 2013, effective Jun 19, 2013
Iniziative Industriali Italiane S.p.A. Airplanes
We are adopting a new airworthiness directive (AD) for Iniziative Industriali Italiane S.p.A. Models Sky Arrow 650 TC, Sky Arrow 650 TCN, Sky Arrow 650TCS, and Sky Arrow 650TCNS airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as improper installation of the spherical bearing on the central hinge lever and a crack on the weld length of the horizontal tail/elevator plane hinge assembly. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-11-04 · published Jun 4, 2013, effective Jul 9, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes; Model 767-200, -300, -300F, and -400ER series airplanes; and Model 777-200, -200LR, -300, and -300ER series airplanes. This AD was prompted by operator or in-service reports of burned Boeing Material Specification (BMS) 8-39 urethane foam, and a report from the airplane manufacturer indicating that airplanes were assembled, throughout various areas of the airplane (including flight deck and cargo compartments), with seals made of BMS 8-39 urethane foam, a material with fire-retardant properties that deteriorate with age. This AD requires replacing certain seals made of BMS 8-39 urethane foam. We are issuing this AD to prevent the failure of urethane seals to maintain sufficient Halon concentrations in the cargo compartments to extinguish or contain fire or smoke, and to prevent penetration of fire or smoke in areas of the airplane that are difficult to access for fire and smoke detection or suppression.
AD 2013-11-06 · published Jun 4, 2013, effective Jul 9, 2013
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model Mystere-Falcon 900 and Falcon 900EX airplanes. This AD was prompted by reports of chafing between the tail strobe power supply and a hydraulic line. This AD requires modifying the tail strobe power supply wire routing. We are issuing this AD to prevent chafing between the tail strobe power supply and a hydraulic line, which could result in hydraulic fluid leakage and possible fire due to arcing, and consequent loss of control of the airplane due to structural failure of the tail.
AD 2013-11-07 · published Jun 4, 2013, effective Jul 9, 2013
Embraer S.A. Airplanes
We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 190 airplanes. This AD was prompted by reports of cracks on the side stay of the main landing gear (MLG). This AD requires repetitive measurements of the left-hand (LH) and right-hand (RH) MLG side stay support fitting to detect bushing migration, and eventual replacement of the bushing; and a detailed inspection for damage on the LH and RH MLG side stay support assembly, and related investigative and corrective actions if necessary. We are issuing this AD to prevent excessive bearing friction, which might compromise the MLG free fall extension and cause fatigue cracking on the MLG side stay and on its support assembly, resulting in reduced structural integrity of the MLG.
AD 2013-11-12 · published Jun 4, 2013, effective Jul 9, 2013
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model BD-100-1A10 (Challenger 300) airplanes. This AD was prompted by reports of failure of a screw cap or end cap of the hydraulic system accumulator while on the ground, which resulted in loss of use of that hydraulic system and high-energy impact damage to adjacent systems and structures. This AD would require inspecting for the correct serial number of a certain hydraulic system accumulator, and replacing affected hydraulic system accumulators with new or serviceable accumulators. We are issuing this AD to prevent failure of a screw cap or end cap and loss of the related hydraulic system, which could result in damage to airplane structure and consequent reduced controllability of the airplane.
AD 2013-10-04 · published Jun 12, 2013, effective Jul 17, 2013
Piper Aircraft, Inc. Airplanes
We are superseding an existing airworthiness directive (AD) for all Piper Aircraft, Inc. Models PA-31, PA-31-325, and PA-31-350 airplanes. That AD currently requires a detailed repetitive inspection of the exhaust system downstream of the turbochargers and repair or replacement of parts as necessary. This new AD requires visual repetitive inspections, expanding the inspection scope to include the entirety of each airplane exhaust system. This AD was prompted by reports of exhaust system failures upstream of aircraft turbochargers and between recurring detailed inspections. We are issuing this AD to correct the unsafe condition on these products.
AD 2013-11-14 · published Jun 14, 2013, effective Jul 19, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes. This AD was prompted by reports of hydraulic fluid contamination (including contamination caused by hydraulic fluid in its liquid, vapor, and/or solid (coked) form) found in the strut forward dry bay. This AD requires repetitive general visual inspections of the strut forward dry bay for the presence of hydraulic fluid, and related investigative and corrective actions (including checking drain lines for blockage due to hydraulic fluid coking, and cleaning or replacing drain lines to allow drainage) if necessary. We are issuing this AD to detect and correct hydraulic fluid contamination of the strut forward dry bay, which could result in hydrogen embrittlement of the titanium forward engine mount bulkhead fittings, and consequent inability of the fittings to carry engine loads, resulting in engine separation. Hydraulic embrittlement also could cause a through-crack formation across the fittings through which an engine fire could breach into the strut, resulting in an uncontained strut fire.
AD 2013-11-16 · published Jun 17, 2013, effective Jul 2, 2013
Hawker Beechcraft Corporation (Type Certificate Previously Held by Raytheon Aircraft Company) Airplanes
We are adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation (Type Certificate Previously Held by Raytheon Aircraft Company) Model BAe.125 Series 800A (including C-29A and U-125), and 800B airplanes; and Model Hawker 800 (including variant U-125A) and 800XP airplanes modified in accordance with a certain winglet supplemental type certificate. This AD requires revising the Limitations section of the airplane flight manual (AFM) and installing placards on the instrument panel. This AD was prompted by reports of several instances of severe vibration and wing/aileron oscillations. We are issuing this AD to prevent vibration and wing/aileron oscillations, which could cause structural damage or lead to divergent flutter, and result in loss of integrity of the wing, loss of control of the airplane, and in-flight breakup.
AD 2013-01-01 · published Jun 18, 2013, effective Jul 23, 2013
Bombardier, Inc. Airplanes
We are superseding an existing airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. That AD currently requires revising the airplane flight manual, deactivating and removing certain hydraulic accumulators, inspecting for cracks on accumulators and screw caps, and replacing certain accumulators. For certain airplanes, this new AD reduces the compliance time for a certain replacement. This AD was prompted by reports of on-ground hydraulic accumulator screw cap/end cap failure. We are issuing this AD to detect and correct hydraulic accumulator screw cap/end cap failure, which could result in the loss of the associated hydraulic system and high-energy impact damage to adjacent systems and structure, and consequent loss of control of the airplane.
AD 2013-05-11 · published Jun 21, 2013, effective Jul 26, 2013
Airbus Airplanes
We are superseding an existing airworthiness directive (AD) for certain Airbus Model A318, A319, A320, and A321 series airplanes. That AD currently requires one-time and repetitive inspections of specific areas and, when necessary, corrective actions for those rudders where production rework has been identified. This new AD adds airplanes with certain rudders to the AD applicability; changes an inspection type for certain reinforced rudder areas; requires pre- inspections and repairs if needed; and requires permanent restoration of vacuum loss holes. This AD also requires additional inspections for certain rudders and repair if needed, and requires replacement of certain rudders with new rudders. This AD was prompted by reports of surface defects on rudders that were the result of debonding between the skin and honeycomb core. We are issuing this AD to detect and correct extended de-bonding, which might degrade the structural integrity of the rudder. The loss of the rudder leads to degradation of the handling qualities and reduces the controllability of the airplane.
AD 2013-11-10 · published Jun 21, 2013, effective Jul 26, 2013
Cessna Aircraft Company Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) (previously COLUMBIA or LANCAIR) Models LC40-550FG, LC41-550FG, and LC42-550FG airplanes. This AD was prompted by reports that during maximum braking, if the brakes lock up and a skid occurs, a severe oscillatory yawing motion or "wheel walk" may develop, which could result in further significant structural damage to the airplane. This AD requires insertions into the pilot's operating handbook (POH) and the airplane maintenance manuals (AMM) regarding proper use of the brakes and inspection of the aft fuselage. We are issuing this AD to correct the unsafe condition on these products.
AD 2013-11-08 · published Jun 24, 2013, effective Jul 29, 2013
Pilatus Aircraft Ltd. Airplanes
We are superseding an existing airworthiness directive (AD) for Pilatus Aircraft Ltd. Models PC-6, PC-6-H1, PC-6-H2, PC-6/350, PC- 6/350-H1, PC-6/350-H2, PC-6/A, PC-6/A-H1, PC-6/A-H2, PC-6/B-H2, PC-6/ B1-H2, PC-6/B2-H2, PC-6/B2-H4, PC-6/C-H2, and PC-6/C1-H2 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as failure to inspect and maintain stabilizer-trim attachment components and the flap actuator could result in loss of control. We are issuing this proposed AD to require actions to address the unsafe condition on these products.
AD 2013-11-11 · published Jun 27, 2013, effective Aug 1, 2013
Cessna Aircraft Company Airplanes
We are superseding AD 2000-04-01 that applies to certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182S, 182T, T182T, 206H, and T206H airplanes. AD 2000-04-01 currently requires an inspection of the engine oil pressure switch and, if applicable, replacement of the engine oil pressure switch. This AD increases the applicability of the AD, places a life-limit of 3,000 hours time-in- service on the engine oil pressure switch, and requires replacement when the engine oil pressure switch reaches its life limit. This AD was prompted by new reports of internal failure of the engine oil pressure switch, which could result in complete loss of engine oil with consequent partial or complete loss of engine power or fire. We are issuing this AD to correct the unsafe condition on these products.
AD 2013-13-02 · published Jun 27, 2013, effective Aug 1, 2013
B-N Group Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for all B-N Group Ltd. Models BN-2, BN-2A, BN2A MK. III, BN2A MK. III-2, BN2A MK. III-3, BN-2A-2, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A-27, BN-2A-3, BN-2A- 6, BN-2A-8, BN-2A-9, BN-2B-20, BN-2B-21, BN-2B-26, BN-2B-27, BN-2T, and BN-2T-4R airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as inadequate sealing of the fuel filler cap (fuel tank cap) and the fuel filler receptacle (fuel tank opening), which could lead to contaminated fuel and result in in-flight shutdown of the engine. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-13-05 · published Jun 27, 2013, effective Aug 1, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 747SP series airplanes, and certain The Boeing Company Model 747-100B SUD and 747-300 series airplanes. This AD was prompted by an evaluation by the design approval holder indicating that the fuselage skin just above certain lap splice locations is subject to widespread fatigue damage. This AD requires repetitive inspections for cracking of the fuselage skin above certain lap splice locations, and repair if necessary. We are issuing this AD to detect and correct fatigue cracking of the fuselage skin, which could result in reduced structural integrity of the airplane and sudden loss of cabin pressure.
AD 2013-09-04 · published Jun 28, 2013, effective Aug 2, 2013
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by reports of chafing found on the main landing gear (MLG) yoke. The chafing was attributed to contact between the nacelle fire detection wires and the MLG yoke. This AD requires inspections of the nacelle fire detection wires and the MLG yoke for damage; replacing nacelle fire detection wires, if necessary; repairing the MLG yoke, if necessary; and installing brackets and associated hardware to secure the fire detection wires. We are issuing this AD to prevent chafing between the nacelle fire detection wires and the MLG yoke. Chafing could lead to cracking and subsequent failure of the MLG yoke, which could adversely affect the safe landing of the airplane. In addition, chafing of the nacelle fire detection wires could cause them to fail and prevent the detection of a fire in the nacelle assembly.
AD 2013-11-05 · published Jun 4, 2013, effective Jun 19, 2013
Bell Helicopter Textron, Inc. (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for Bell Model 214B, 214B-1, and 214ST helicopters with a certain tail rotor hanger bearing (bearing) installed. This AD requires inspecting the bearing to determine whether an incorrectly manufactured seal material is installed on the bearing. This AD is prompted by a report that certain bearings were manufactured with an incorrect seal material that does not meet Bell specifications. The actions specified by this AD are intended to prevent loss of bearing grease, failure of the bearing, and subsequent loss of control of the helicopter.
AD 2013-11-15 · published Jun 21, 2013, effective Jul 26, 2013
Eurocopter Deutschland GmbH Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland GmbH (Eurocopter) Model BO-105A, BO-105C, BO- 105S, BO-105LS A-1, BO-105LS A-3, EC135 P1, EC135 P2, EC135 P2+, EC135 T1, EC135 T2, EC135 T2+, MBB-BK 117 A-1, MBB-BK 117 A-3, MBB-BK 117 A- 4, MBB-BK 117 B-1, MBB-BK 117 B-2, MBB-BK 117 C-1, and MBB-BK 117 C-2 helicopters with certain part-numbered cantilever assemblies, cyclic stick locking devices, or cyclic stick holder assemblies installed. This AD requires modifying and identifying the cyclic stick cantilever or lock. This AD was prompted by pilots inadvertently taking off with the cyclic locked. The actions of this AD are intended to prevent a pilot taking off with the cyclic in the locked position, which could result in loss of control of the helicopter.
AD 2013-12-07 · published Jun 27, 2013, effective Aug 1, 2013
Bell Helicopter Textron Canada Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron Canada (BHTC) Model 407 helicopters with certain tailboom assemblies installed. This AD requires, at specified intervals, inspecting the tailboom assembly for a crack, loose rivet, or other damage. This AD was prompted by a stress analysis of the tailboom skin that revealed that high-stress-concentration areas are susceptible to skin cracking. This condition, if not detected, could result in a crack in the tailboom assembly, failure of the tailboom, and subsequent loss of control of the helicopter.
AD 2013-12-04 · published Jun 28, 2013, effective Aug 2, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France Model EC 155B, EC155B1, SA-366G1, SA-365N, SA-365N1, AS-365N2, and AS 365 N3 helicopters, which requires modifying the fuel tank draining system. This AD is prompted by a closed fuel tank drain that, in the event of a fuel leak, could result in fuel accumulating in an area containing electrical equipment. The actions are intended to prevent accumulation of fuel in an area with electrical equipment or another ignition source, which may lead to a fire.
AD 2013-11-13 · published Jun 10, 2013, effective Jul 15, 2013
Rolls-Royce plc Turbojet Engines
We are adopting a new airworthiness directive (AD) for all Rolls-Royce plc (RR) Viper Mk. 601-22 turbojet engines. This AD requires reducing the life of certain critical parts. This AD was prompted by a review carried out by RR of the lives of these parts. We are issuing this AD to prevent failure of life-limited parts, damage to the engine, and damage to the airplane.
AD 2013-12-02 · published Jun 14, 2013, effective Jul 19, 2013
Engine Alliance Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Engine Alliance GP7270 and GP7277 turbofan engines. This AD was prompted by damage to the high-pressure compressor (HPC) stage 7-9 spool caused by failure of the baffle plate feature on affected HPC stage 6 disks. This AD requires initial and repetitive borescope inspections of the baffle plate feature and removal from service of the HPC stage 6 disk if the plate is missing material. This AD also requires mandatory removal from service of these HPC stage 6 disks at the next HPC module exposure. We are issuing this AD to prevent failure of the HPC stage 7-9 spool, uncontained engine failure, and damage to the airplane.
AD 2013-12-03 · published Jun 14, 2013, effective Jun 14, 2013
Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) BR700-725A1-12 turbofan engines with fuel pump tube part number FW64852 installed. This AD requires removal of the affected fuel pump tube and its replacement with a part eligible for installation. This AD was prompted by the discovery that cracks have occurred in the affected fuel pump tube between the fuel metering unit and the main fuel pump. We are issuing this AD to prevent loss of fuel supply to the engine, which could result in in-flight engine shutdown of one or more engines, loss of thrust control and damage to the airplane.
AD 2013-12-01 · published Jun 24, 2013, effective Jul 29, 2013
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Rolls-Royce plc (RR) model RB211 Trent 768-60, 772-60, and 772B-60 turbofan engines. This AD was prompted by low-pressure (LP) compressor blade partial airfoil release events. This AD requires a one-time ultrasonic inspection of LP compressor blades that had accumulated more than 2,500 flight cycles (FC) since new. We are issuing this AD to prevent LP compressor blade airfoil separations, engine damage, and damage to the airplane.
AD 2013-10-52 · published Jun 26, 2013, effective Jun 26, 2013
General Electric Company Turbofan Engines
We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) GE90-110B1 and GE90-115B turbofan engines. This emergency AD was sent previously to all known U.S. owners and operators of these engines. This AD prohibits operation of an airplane with affected transfer gearbox assemblies (TGBs) installed on both engines five days after the effective date of this AD. This AD was prompted by reports of two failures of TGBs which resulted in in-flight shutdowns (IFSDs). We are issuing this AD to prevent additional IFSDs of one or more engines, loss of thrust control, and damage to the airplane.
AD 2013-06-51 · published Jun 28, 2013, effective Jul 15, 2013
Various Helicopter Models
We are publishing a new airworthiness directive (AD) for various model helicopters with certain part-numbered and serial- numbered Goodrich externally-mounted hoists installed. This AD requires performing a cable conditioning lift and a load inspection test, deactivating or replacing any hoist that fails the load inspection test, and recording the results of the load inspection test. This AD is prompted by a report of a failure of the overload clutch resulting in an in-flight failure of a hoist containing a dummy load during a maintenance flight. These actions are intended to detect conditions that may result in failure of the hoist and injury to persons being lifted.
