30 Airworthiness Directives: 24 airplane, 3 rotorcraft, 2 engine, 1 glider.
AD 2010-23-26 · published Dec 1, 2010, effective Jan 5, 2011
Airbus Model A300 B2-1C, B2K-3C, B2-203, B4-2C, B4-103, and B4-203 Airplanes; and Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, and F4-605R Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-24-11 · published Dec 1, 2010, effective Jan 5, 2011
The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires sealing the fasteners on the front and rear spars inside the main fuel tank and on the lower panel of the center fuel tank, inspecting the wire bundle support installation in the equipment cooling system bays to identify the type of clamp installed and determine whether the Teflon sleeve is installed, and doing related corrective actions if necessary. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent arcing at certain fuel tank fasteners in the event of a lightning strike or fault current event, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
AD 2010-24-07 · published Dec 7, 2010, effective Jan 11, 2011
Airbus Model A318-111 and A318-112 Airplanes and Model A319, A320, and A321 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-25-01 · published Dec 7, 2010, effective Jan 11, 2011
Diamond Aircraft Industries GmbH Models DA 40 and DA 40F Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires changing the emergency open doors procedure by incorporation of a temporary revision into the FAA- approved airplane flight manual (AFM) for all airplanes. This AD also requires replacement of the passenger door retaining bracket with an improved design retaining bracket for certain airplanes. This AD was prompted by several reports of the rear passenger door departing the airplane in flight. We are issuing this AD to change the emergency open doors procedure and retrofit the rear passenger door retaining bracket, which if not corrected could result in the rear passenger door departing the airplane in flight.
AD 2010-25-02 · published Dec 7, 2010, effective Jan 11, 2011
British Aerospace Regional Aircraft Models Jetstream Series 3101 and Jetstream Model 3201 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-25-03 · published Dec 7, 2010, effective Jan 11, 2011
Airbus Model A300 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-25-04 · published Dec 7, 2010, effective Jan 11, 2011
McDonnell Douglas Corporation Model DC-9-30, DC-9-40, and DC-9-50 Series Airplanes, Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), and DC-9-87 (MD-87) Airplanes, and Model MD-88 and MD-90-30 Airplanes
We are adopting a new airworthiness directive (AD) for the McDonnell Douglas Corporation airplanes listed above. This AD requires modifying the fuel boost pumps for the center wing, and forward or aft auxiliary fuel tanks. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent possible sources of ignition in a fuel tank caused by an electrical fault in the fuel boost pumps. An ignition source in the fuel tank could result in a fire or an explosion and consequent loss of the airplane.
AD 2010-26-53 · published Dec 10, 2010
Cessna Aircraft Company Airplanes
AD 2010-24-12 · published Dec 16, 2010, effective Jan 20, 2011
The Boeing Company Model 777-200, -300, and -300ER Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 777-200, -300, and -300ER series airplanes. This AD requires installing Teflon sleeving under the clamps of certain wire bundles routed along the fuel tank boundary structure, and cap sealing certain penetrating fasteners of the main and center fuel tanks. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent electrical arcing on the fuel tank boundary structure or inside the fuel tanks, which could result in a fire or explosion.
AD 2010-24-13 · published Dec 16, 2010, effective Jan 20, 2011
The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747SR, and 747SP Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires adding two new indicator lights on a certain panel to inform the captain and first officer of a low pressure condition in the left and right override/jettison pumps of the center wing tanks. This AD also requires replacing the left and right override/jettison switches on the M154 fuel control module on the P4 panel with improved switches and doing the associated wiring changes. This AD also requires, for certain airplanes, installation of a mounting bracket for the new indicator lights. This AD also requires a revision to the maintenance program to incorporate airworthiness limitation No. 28-AWL-22. This AD also requires a revision to the airplane flight manual to advise the flightcrew what to do in the event that the pump low pressure light on the flight engineer's panel does not illuminate when the pump is selected off. This AD was prompted by fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent uncommanded operation of the override/jettison pumps of the center wing tanks, and failure to manually shut off the override/ jettison pumps at the correct time, either of which could lead to an ignition source inside the center wing tank. This condition, in combination with flammable fuel vapors, could result in a center fuel tank explosion and consequent loss of the airplane.
AD 2010-26-01 · published Dec 16, 2010, effective Jan 20, 2011
The Boeing Company Model 777-200 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 777-200 series airplanes. This AD requires installing a new insulation blanket on the latch beam firewall of each thrust reverser (T/R) half. This AD results from an in-flight shutdown due to an engine fire indication; an under-cowl engine fire was extinguished after landing. The cause of the fire was uncontained failure of the starter in the engine core compartment; the fire progressed into the latch beam cavity and was fueled by oil from a damaged integrated drive generator oil line. We are issuing this AD to prevent a fire from entering the cowl or strut area, which could weaken T/R parts and result in reduced structural integrity of the T/R, possible separation of T/R parts during flight, and consequent damage to the airplane and injury to people or damage to property on the ground.
AD 2010-26-02 · published Dec 16, 2010, effective Jan 20, 2011
Pacific Aerospace Limited Model FU24-954 and FU24A-954 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-26-03 · published Dec 16, 2010, effective Dec 20, 2010
Hawker Beechcraft Corporation Models B200, B200GT, B300, and B300C Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. That AD currently requires fabricating and installing a placard incorporating information that limits operation when there is known or forecast icing and requires replacing a section of the pneumatic supply tube for the tail deice system with a new tube of a different material. This AD requires fabricating and installing a placard incorporating information that limits operation when there is known or forecast icing and requires replacing the entire length of the pneumatic supply tube for the tail deice system with a new tube of a different material. This AD was prompted by reports of two failures of the pneumatic supply tube for the tail deice system outside the area covered by AD 2008-07-10. We are issuing this AD to prevent collapsed pneumatic supply tubes, which could result in failure of the tail deice boots to operate. This failure could lead to loss of control in icing conditions.
AD 2011-01-51 · published Dec 18, 2010
Piaggio Aero Industries S.p.A. Airplanes
AD 2010-26-05 · published Dec 21, 2010, effective Jan 25, 2011
DASSAULT AVIATION Model Falcon 10 Airplanes; Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, and G Airplanes; Model MYSTERE-FALCON 200 Airplanes; Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 Airplanes; Model FALCON 2000 and FALCON 2000EX Airplanes; and Model MYSTERE-FALCON 50 and MYSTERE-FALCON 900 Airplanes, and FALCON 900EX Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-25-06 · published Dec 28, 2010, effective Feb 1, 2011
The Boeing Company Model 737-200, -300, -400, and -500 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 737-200, -300, -400, and -500 series airplanes. This AD requires repetitive inspections for cracking of certain fuselage frames and stub beams, and corrective actions if necessary. This AD also provides for an optional repair, which would terminate the repetitive inspections. For airplanes on which a certain repair is done, this AD also requires repetitive inspections for cracking of certain fuselage frames and stub beams, and corrective actions if necessary. This AD results from reports of the detection of fatigue cracks at certain frame sections, in addition to stub beam cracking, caused by high flight cycle stresses from both pressurization and maneuver loads. We are issuing this AD to detect and correct fatigue cracking of certain fuselage frames and stub beams and possible severed frames, which could result in reduced structural integrity of the frames. This reduced structural integrity can increase loading in the fuselage skin, which will accelerate skin crack growth and could result in rapid decompression of the fuselage.
AD 2010-26-04 · published Dec 28, 2010, effective Feb 1, 2011
Piper Aircraft, Inc. Model PA-28-161 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above that are equipped with Thielert Aircraft Engine GmbH (TAE) Engine Model TAE-125-01 installed per Supplemental Type Certificate (STC) No. SA03303AT. This AD requires installing a full authority digital engine control (FADEC) backup battery, replacing the supplement pilot's operating handbook and FAA approved airplane flight manual, and revising the limitations section of the supplement airplane maintenance manual. This AD was prompted by an incident where an airplane experienced an in-flight engine shutdown caused by a momentary loss of electrical power to the FADEC. We are issuing this AD to prevent interruption of electrical power to the FADEC, which could result in an uncommanded engine shutdown. This failure could lead to a loss of engine power.
AD 2010-26-06 · published Dec 28, 2010, effective Feb 1, 2011
The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires inspections for scribe lines in the fuselage skin at lap joints, the splice strap at certain butt joints, the skin or doubler at certain approved repair doublers, and the skin at decal locations; and related investigative and corrective actions if necessary. This AD results from reports of scribe line damage found adjacent to the skin lap joints, decals, and wing-to-body fairings. We are issuing this AD to detect and correct scribe lines, which can develop into fatigue cracks in the skin. Undetected fatigue cracks can grow and cause sudden decompression of the airplane.
AD 2010-26-07 · published Dec 28, 2010, effective Feb 1, 2011
The Boeing Company Model 747 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires repetitive inspections for cracking in the body skin around the aft corners of the nose wheel well; for certain airplanes, repetitive inspections for cracking in the skin splice plate at the aft corners of the nose wheel well; and related investigative and corrective actions if necessary. This AD also requires repetitive post-modification inspections for cracking in the body skin and the skin splice plate; for certain airplanes, an inspection for steel cross-shaped doublers on the larger aluminum doublers; and corrective action if necessary. This AD also requires repetitive surface high frequency eddy current (HFEC) inspections of a certain bulkhead outer chord, skin splice plate, and outer chord radius filler for cracking; repetitive detailed inspections for cracking of the bulkhead frame web and body skin; and corrective actions if necessary. This AD provides for optional terminating action for certain repetitive inspections. This AD was prompted by reports of cracking of the fuselage skin and adjacent internal skin splice plate at the left and right nose wheel well aft corners, and the outer chord of the body station (BS) 400 bulkhead. We are issuing this AD to detect and correct cracking of the fuselage skin or splice plate, which, together with cracking of the bulkhead outer chord, could result in large skin cracks and subsequent in-flight rapid decompression of the airplane.
AD 2010-26-08 · published Dec 28, 2010, effective Feb 1, 2011
The Boeing Company Model 767 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires a detailed inspection of the entryway door movable ceiling panel for pin migration at either end of the hinge assembly and damage to the pin; a detailed inspection for correct crimp at both ends and damage to hinge stock; a detailed inspection of the ceiling area for any visible cosmetic and/or tie-rod chafing that could be caused by a migrated hinge pin; a detailed inspection for wire damage and/or breakage; and other specified and corrective actions if necessary. This AD results from reports of fault messages caused by improperly crimped hinge pins coming into contact with wires and causing damage. We are issuing this AD to detect and correct improperly crimped hinge pins, which could damage tie rods and wire bundles, causing shorts in many systems, including the spar fuel shut-off valve, oxygen mask deployment, and burned wires, which could be an ignition source in a hidden area of the airplane.
AD 2010-26-10 · published Dec 28, 2010, effective Feb 1, 2011
The Boeing Company Model 747-200C, -200F, -400, -400D, and -400F Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Model 747-200C, -200F, -400, -400D, and -400F series airplanes. That AD currently requires repetitive inspections for cracks in the overlapping (upper) skin of the upper fastener row of the lap joints of the fuselage skin in sections 41, 42, and 46; and related investigative and corrective actions, if necessary. This new AD expands the inspection area in the existing AD, and adds a modification of certain lap joints and certain post-repair inspections of the lap joints. Accomplishing the modification would end the repetitive inspections required by the existing AD for the length of lap joint that is modified. This AD results from a structural review of affected skin lap joints for widespread fatigue damage. We are issuing this AD to prevent fatigue cracking in certain lap joints, which could result in rapid depressurization of the airplane.
AD 2010-26-12 · published Dec 28, 2010, effective Jan 12, 2011
Airbus Model A321-211, -212, -231, and -232 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-26-13 · published Dec 28, 2010, effective Feb 1, 2011
Bombardier, Inc. Model DHC-8-300 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-17-18 R1 · published Dec 30, 2010, effective Jan 14, 2011
Air Tractor, Inc. Models AT-802 and AT-802A Airplanes
We are revising an existing airworthiness directive (AD) for Air Tractor, Inc. (Air Tractor) Models AT-802 and AT-802A airplanes. That AD currently requires you to repetitively inspect (using the eddy current method) the two outboard fastener holes in both of the wing main spar lower caps at the center splice joint for cracks and repair or replace any cracked spar, and changes the safe life for certain serial (SN) ranges. This AD retains the actions of AD 2010-17-18 and reduces the applicability from all serial numbers beginning with SN- 0001 as required by the previous AD to SN-0001 through SN-0269. This AD was prompted by our evaluation of a comment from David Ligon, Air Tractor, and our determination that we should reduce the applicability from that already required by the previous AD. We are issuing this AD to detect and correct cracks in the wing main spar lower cap at the center splice joint, which could result in failure of the spar cap and lead to wing separation and loss of control of the airplane.
AD 2011-01-52 · published Dec 20, 2010
Schweizer Aircraft Corporation Helicopters
AD 2010-26-11 · published Dec 21, 2010, effective Jan 5, 2011
Kaman Aerospace Corporation (Kaman) Model K-1200 Helicopters
We are adopting a new airworthiness directive (AD) for the Kaman Model K-1200 helicopters. This AD requires revising the Limitations section of the Instructions for Continued Airworthiness (ICA) by establishing a life limit of 8,000 hours time-in-service (TIS) for each main rotor blade (blade) set. Also, this AD requires removing each blade set from service if it has accumulated 8,000 or more hours time-in-service (TIS). This AD also requires replacing certain blade sets with airworthy blade sets at specified intervals based on the blade set serial number (S/N). This AD was prompted by an accident and the subsequent discovery of cracks in multiple blade spars. We are issuing this AD to prevent blade failure and subsequent loss of control of the helicopter.
AD 2010-26-09 · published Dec 28, 2010, effective Jan 12, 2011
Sikorsky Aircraft Corporation (Sikorsky) Model S76A, B, and C Helicopters
This amendment supersedes an existing emergency airworthiness directive (EAD) for the specified Sikorsky model helicopters. The EAD requires inspecting the LITEF Attitude Heading and Reference System (AHRS) unit of the navigation system to determine if it is at a Mod Status "18." If either AHRS unit is at Mod Status "18," the EAD requires installing placards on the instrument panel to prohibit single pilot instrument flight rule (IFR) and single pilot night flight and reducing airspeeds to 120 knots indicated airspeed (KIAS) if both autopilots uncouple during instrument meteorological conditions (IMC) or night flight. The EAD also requires inserting minimum crew and airspeed limitations into the Limitations section of the applicable Rotorcraft Flight Manual (RFM) to limit the minimum flight crew to 2 pilots for night flight and IFR flight and to reduce airspeed to 120 KIAS if both autopilots uncouple during IMC or night flight. This amendment contains the same requirements but draws the appropriate distinctions between IFR and IMC as used in the intended operating limitations. Also, unlike the EAD, this AD states the airspeed must be reduced to 120 KIAS if both autopilots uncouple during IMC or night flight. Further, we are removing the limitation contained in the Active Temporary Revisions relating to pilots keeping their hands and feet near the flight controls. This AD was prompted by the need to supersede the EAD to state the distinction between IFR and IMC as used in the operating limitations and to reduce the airspeed to 120 KIAS if both autopilots uncouple during IMC or night flight. The actions specified by this AD are intended to implement operating limitations based on an anomaly in the AHRS related to the 26 volt AC inverter that could result in a decoupling of both autopilots and to prevent loss of control of the helicopter during IMC and during night flight.
AD 2010-25-05 · published Dec 9, 2010, effective Jan 13, 2011
Rolls-Royce Deutschland Ltd & Co KG Models BR700-710A1-10; BR700-710A2-20; and BR700-710C4-11 Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2010-24-14 · published Dec 17, 2010, effective Jan 21, 2011
Pratt & Whitney PW4000 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain Pratt & Whitney PW4000 series turbofan engines. This AD requires initial and repetitive borescope inspections (BSI) or fluorescent penetrant inspections (FPI) for cracks in the anti-vortex tube (AVT) shelf slots on the 10th stage disk of the high-pressure compressor (HPC) drum rotor disk assembly. This AD results from 47 reports received since 2007 of HPC 10th stage disks found cracked in the AVT shelf slots during shop visit inspections. We are issuing this AD to prevent failure of the HPC 10th stage disk, uncontained engine failure, and damage to the airplane.
AD 2010-24-10 · published Dec 1, 2010, effective Jan 5, 2011
CENTRAIR Models 101, 101A, 101P, and 101AP Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
