40 Airworthiness Directives: 32 airplane, 2 rotorcraft, 3 engine, 1 propeller, 2 appliance.
AD 2008-07-11 · published Apr 4, 2008, effective May 9, 2008
PILATUS AIRCRAFT LTD. Model PC-12, PC-12/45, and PC-12/47 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. This AD requires inserting changes into the airworthiness limitations of the FAA-approved maintenance program. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2008-07-10 · published Apr 7, 2008, effective Apr 10, 2008
Hawker Beechcraft Corporation Models B200, B200GT, B300, and B300C Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Hawker Beechcraft Corporation (HBC) Models B200, B200GT, B300, and B300C airplanes. This AD requires you to fabricate and install a placard incorporating information that limits operation when there is known or forecast icing and requires you to replace a section of the pneumatic supply tube for the tail deice system with a new tube of a different material. This AD results from reports of collapsed tail deice boot pneumatic supply tubes. We are issuing this AD to prevent collapsed pneumatic supply tubes, which could result in failure of the tail deice boots to operate. This failure could lead to loss of control in icing conditions.
AD 2008-08-02 · published Apr 14, 2008, effective May 19, 2008
Boeing Model 727 Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 727 airplanes. This AD requires repetitive inspections for cracking or corrosion of the threaded end of the lower segment of the main landing gear (MLG) side strut, and corrective actions if necessary. This AD also requires prior or concurrent inspection for cracking or corrosion of the threads and thread relief area of the lower segment, corrective action if necessary, and re-assembly using corrosion inhibiting compound. This AD results from reports of the threads cracking on the MLG side strut lower segment. We are issuing this AD to prevent a fractured side strut, which could result in collapse of the MLG.
AD 2008-08-03 · published Apr 14, 2008, effective May 19, 2008
Pacific Aerospace Limited Model 750XL Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-04 · published Apr 14, 2008, effective May 19, 2008
Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A318, A319, A320, and A321 airplanes. That AD currently requires repetitive inspections for cracking in the forward lug of the support rib 5 fitting of both main landing gear (MLG), and repair if necessary. The existing AD also provides optional terminating actions for certain airplanes, as well as other optional methods for complying with the inspection requirements of the existing AD. This new AD continues to require repetitive inspections for cracking in the forward lug of the support rib 5 fitting of the left and right MLG at new repetitive intervals in accordance with new service information, and repair or replacement of any cracked MLG fitting if necessary. This new AD also requires modification of the rib bushings of the left and right MLG, which would end the repetitive inspections. This AD results from cracks found in the forward lug of the MLG support rib 5 fitting. We are issuing this AD to prevent cracking in the forward lug of the MLG, which could result in failure of the lug and consequent collapse of the MLG during takeoff or landing.
AD 2008-08-05 · published Apr 14, 2008, effective May 19, 2008
Fokker Model F.27 Mark 050 and F.28 Mark 0100 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-06 · published Apr 14, 2008, effective Apr 21, 2008
Bombardier Inc. Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to all Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes and Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604) series airplanes. The existing AD currently requires revising the airplane flight manuals (AFMs) to include a new cold weather operations limitation. This AD requires revising the AFMs to modify the cold weather operations limitation and include additional limitations and procedures. This AD results from reports of uncommanded roll during take-off. We are issuing this AD to prevent possible loss of control on take-off resulting from even small amounts of frost, ice, snow, or slush on the wing leading edges or forward upper wing surfaces. DATES: This AD becomes effective April 21, 2008. The Director of the Federal Register approved the incorporation by reference of certain publications listed in the AD as of April21, 2008. On February 22, 2005 (70 FR 8025, February 17, 2005), the Director of the Federal Register approved the incorporation by reference of certain other publications. We must receive any comments on this AD by May 14, 2008.
AD 2008-08-07 · published Apr 14, 2008, effective May 19, 2008
Saab Model SAAB-Fairchild SF340A (SAAB/SF340A) and SAAB 340B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-08 · published Apr 14, 2008, effective May 19, 2008
Boeing Model 757 Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires an inspection to determine the manufacturer and manufacture date of the oxygen masks in the passenger service units and the lavatory and attendant box assemblies, and corrective action if necessary. This AD results from a report that several passenger masks with broken in-line flow indicators were found following a mask deployment. We are issuing this AD to prevent the in- line flow indicators of the passenger oxygen masks from fracturing and separating, which could inhibit oxygen flow to the masks and consequently result in exposure of the passengers and cabin attendants to hypoxia following a depressurization event.
AD 2008-08-09 · published Apr 14, 2008, effective May 19, 2008
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 400) airplanes. That AD currently requires revising the airworthiness limitations section of the Instructions for Continued Airworthiness of the maintenance requirements manual (MRM) by incorporating procedures for repetitive functional tests of the pilot input lever of the pitch feel simulator (PFS) units. That AD also requires new repetitive functional tests of the pilot input lever of the PFS unit, and corrective actions if necessary; and after initiating the new tests, requires removal of the existing procedures for the repetitive functional tests from the MRM. This new AD requires revised procedures for the functional tests. This AD results from a report that the shear pin located in the input lever of two PFS units failed due to fatigue. We are issuing this AD to prevent undetected failure of the shear pins of both PFS units simultaneously, which could result in loss of pitch feel forces and consequent reduced control of the airplane.
AD 2008-08-10 · published Apr 14, 2008, effective May 19, 2008
Boeing Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. For certain airplanes, this AD requires replacing the outboard stabilizing fitting and certain adjacent components of the main landing gear (MLG) support beam. This AD also requires repetitive inspections for discrepancies of the outboard stabilizing fitting, walking beam hanger, and rear spar attachment, and corrective actions if necessary. For certain airplanes, this AD provides an alternative one-time inspection of the outboard stabilizing fitting for discrepancies, and corrective actions if necessary, which would extend the compliance time for the replacement of the outboard stabilizing fitting. For certain other airplanes, this AD also requires performing a torque check of the aft pin of the outboard stabilizing fitting, and corrective actions if necessary. This AD results from reports of findings of fatigue cracking of the outboard stabilizing fitting and stress corrosion cracking of the bolts attaching the fitting to the wing rear spar. We are issuing this AD to detect and correct that cracking, which could result in disconnection of the MLG actuator from the rear spar and support beam, consequent damage to the hydraulic system, and possible loss of the "A" and "B" hydraulic systems and damage or jamming of the flight control cables. Damage or jamming of the flight control cables could result in loss of control of the airplane.
AD 2008-08-12 · published Apr 14, 2008, effective May 19, 2008
Boeing Model 757 Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 757 airplanes. This AD requires repetitive inspections of the anchor tab of the bulkhead seal assemblies of the wing thermal anti-ice (TAI) system for cracks at certain outboard stations of the left and right wings, and corrective action if necessary. This AD also provides optional terminating action for the repetitive inspections. This AD results from reports of cracks found at the anchor tab of the bulkhead seal assemblies of the wing TAI system. In one incident, the anchor tab and bulkhead seal assembly had separated because of the cracks. We are issuing this AD to prevent failure of the anchor tab of the bulkhead seal assembly, which in icing conditions could result in insufficient airflow to the wing TAI system, subsequent ice on the wings, and consequent reduced controllability of the airplane.
AD 2008-08-13 · published Apr 14, 2008, effective May 19, 2008
Airbus Model A310-304, -322, -324, and -325 Airplanes; and A300 Model B4-601, B4-603, B4-605R, B4-620, B4-622, B4-622R, F4-605R, F4-622R, and C4-605R Variant F Airplanes (Commonly Called Model A300-600 Series Airplanes)
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-15 · published Apr 21, 2008, effective May 27, 2008
DORNIER LUFTFAHRT GmbH Models 228-100, 228-101, 228-200, 228-201, 228-202, and 228-212 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-18 · published Apr 21, 2008, effective May 27, 2008
Fokker Model F.28 Mark 0070 and Mark 0100 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-19 · published Apr 21, 2008, effective May 27, 2008
Gulfstream Aerospace LP Model Gulfstream G150 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-20 · published Apr 21, 2008, effective May 27, 2008
Dassault Model Falcon 2000 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-08-21 · published Apr 21, 2008, effective May 27, 2008
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 Airplanes and Model ERJ 190 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all EMBRAER Model ERJ 170-100 LR, -100 SE, -100 STD, and -100 SU airplanes; and Model ERJ 190-100 IGW, -100 LR, and - 100 STD airplanes. That AD currently requires revising the Limitations section of the airplane flight manual (AFM) to prohibit the flightcrew from moving the throttle into the forward thrust range immediately after applying the thrust reverser. This new AD adds additional airplanes to the applicability and requires the AFM revision for those additional airplanes. For certain airplanes, this AD also requires installing new, improved full-authority digital engine-control (FADEC) software. This AD results from a report that, during landing, the thrust reverser may not re-stow completely if the throttle lever is moved into the forward thrust range immediately after the thrust reverser is applied. We are issuing this AD to prevent the flightcrew from performing a takeoff with a partially deployed thrust reverser, which could result in reduced controllability of the airplane.
AD 2008-08-22 · published Apr 21, 2008, effective May 27, 2008
Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires a one-time inspection to determine the material of the forward and aft gray water drain masts. For airplanes having composite gray water drain masts, this AD requires installation of a bonding jumper between a ground and the clamp on the tube of the forward and aft gray water composite drain masts. This AD results from a report of charred insulation blankets and burned wires around the forward gray water composite drain mast found during an inspection of the forward cargo compartment on a Model 767-300F airplane. We are issuing this AD to prevent a fire near a composite drain mast and possible disruption of the electrical power system caused by a lightning strike on a composite drain mast, which could result in the loss of several functions essential for safe flight.
AD 2008-08-23 · published Apr 21, 2008, effective May 27, 2008
Boeing Model 737-200C Series Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 737-200C series airplanes. This AD requires revising the FAA-approved maintenance inspection program to include inspections that will give no less than the required damage tolerance rating for each structural significant item (SSI), doing repetitive inspections to detect cracks of all SSIs, and repairing cracked structure. This AD results from a report of incidents involving fatigue cracking in transport category airplanes that are approaching or have exceeded their design service objective. We are issuing this AD to maintain the continued structural integrity of the entire fleet of Model 737-200C series airplanes.
AD 2008-08-24 · published Apr 21, 2008, effective May 27, 2008
Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires replacing the drain tube assemblies and support clamps on the aft fairing of the engine struts. This AD results from reports of failure of the drain tube assembly and clamp on the aft fairings of an engine strut. We are issuing this AD to prevent failure of the drain tube assemblies and clamps on the aft fairings of the of the engine struts. Such a failure could allow leaked flammable fluids in the drain systems to discharge on to the heat shields of the aft fairings of the engine struts, which could result in an undetected and uncontrollable fire.
AD 2008-08-25 · published Apr 21, 2008, effective May 27, 2008
Boeing Model 747-400F and -400 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 747-400F and -400 series airplanes. This AD requires installing drains and drain tubes to eliminate water accumulation in the dripshield above the M826 Card File in the main equipment center. This AD results from a report that water from the dripshield entered the card file and damaged a circuit card, causing the AFT CARGO FIRE MSG message to be illuminated and resulting in an air turn back. We are issuing this AD to prevent water from entering the card file and damaging a circuit card. Failure of one or more of the 15 fuel system circuit cards in the card file could cause loss of fuel management, which could cause unavailability of fuel. Failure of one or more of the 35 fire detection circuit cards could cause a false message of a fire, or no message of a fire when there is a fire.
AD 2008-08-26 · published Apr 21, 2008, effective May 27, 2008
Boeing Model 767 Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 767 airplanes. This AD requires a one-time inspection to determine the material of the forward and aft gray water drain masts. For airplanes having composite gray water drain masts, this AD also requires installation of a ground bracket and a bonding jumper between a ground bracket and the clamp on the tube of the forward and aft gray water composite drain masts. This AD results from a report of charred insulation blankets and burned wires around the forward gray water composite drain mast found during an inspection of the forward cargo compartment. We are issuing this AD to prevent a fire near a composite drain mast and possible disruption of the electrical power system caused by a lightning strike on a composite drain mast, which could result in the loss of several functions essential for safe flight.
AD 2008-09-02 · published Apr 21, 2008, effective May 27, 2008
APEX Aircraft Model CAP 10B Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2006-12-10 R1 · published Apr 22, 2008, effective May 7, 2008
Boeing Model 747-400 Series Airplanes
The FAA is revising an existing airworthiness directive (AD) that applies to certain Boeing Model 747-400 series airplanes. That AD currently requires inspecting the support bracket of the crew oxygen cylinder installation to determine the manufacturing date marked on the support, and performing corrective action if necessary. This new AD retains all the requirements of the existing AD and expands the applicability of the existing AD to include certain airplanes that are not on the U.S. Register. This AD results from a report indicating that certain oxygen cylinder supports may not have been properly heat- treated. We are issuing this AD to prevent failure of the oxygen cylinder support under the most critical flight load conditions, which could cause the oxygen cylinder to come loose and leak oxygen. Leakage of oxygen could result in oxygen being unavailable for the flightcrew or could result in a fire hazard in the vicinity of the leakage.
AD 2008-09-01 · published Apr 22, 2008, effective May 27, 2008
Alpha Aviation Design Limited (Type Certificate No. A48EU Previously Held by APEX Aircraft and AVIONS PIERRE ROBIN) Model R2160 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-09-04 · published Apr 22, 2008, effective May 27, 2008
McDonnell Douglas Model DC-8-31, DC-8-32, DC-8-33, DC-8-41, DC-8-42, and DC-8-43 Airplanes; Model DC-8-50 Series Airplanes; Model DC-8F-54 and DC-8F-55 Airplanes; Model DC-8-60 Series Airplanes; Model DC-8-60F Series Airplanes; Model DC-8-70 Series Airplanes; and Model DC-8-70F Series Airplanes
We are adopting a new airworthiness directive (AD) for all McDonnell Douglas airplanes identified above. This AD requires revising the FAA-approved maintenance program to incorporate new airworthiness limitations for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
AD 2008-09-05 · published Apr 22, 2008, effective May 27, 2008
Boeing Model 747 Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 747 airplanes. This AD requires inspecting the trunnion fork assembly of the wing landing gears to determine the part number and serial number and to determine the category of the trunnion fork assemblies. For certain airplanes, this AD also requires, if necessary, various inspections to detect discrepancies of the trunnion fork assemblies, related investigative/corrective actions, and a terminating action. This AD results from a report of a fractured trunnion fork assembly. We are issuing this AD to prevent a fractured trunnion fork assembly, which could result in the collapse of a wing landing gear on the ground and possible damage to hydraulic equipment and the aileron and spoiler cables. Such damage could result in reduced controllability of the airplane.
AD 2008-09-07 · published Apr 23, 2008, effective May 8, 2008
Boeing Model 757 Airplanes and Model 767-200, 767-300, and 767-300F Series Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 757 airplanes and Model 767-200, 767-300, and 767-300F series airplanes. This AD requires revising the Limitations section of the airplane flight manual to advise the flight crew of procedures to follow to ensure that a fuel filter impending bypass condition due to gross fuel contamination is detected in a timely manner. This AD was prompted by an error in the operating program software (OPS) of the engine indication and crew alerting system (EICAS). The error prevents the display of an advisory message to the flight crew of a left engine fuel filter contamination and imminent bypass condition, which may indicate an imminent multiple engine thrust loss or engine malfunction event due to fuel contamination. We are issuing this AD to prevent malfunction and thrust loss on both engines, which could result in a forced off-airport landing.
AD 2008-09-06 · published Apr 28, 2008, effective Jun 2, 2008
Saab Model SAAB-Fairchild SF340A (SAAB/SF340A) and SAAB 340B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-09-09 · published Apr 28, 2008, effective Jun 2, 2008
DORNIER LUFTFAHRT GmbH Models 228-200, 228-201, 228-202, and 228-212 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-09-10 · published Apr 28, 2008, effective May 8, 2008
Air Tractor, Inc. Models AT-300, AT-301, AT-302, AT-400, and AT-400A Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede AD 2003-06-01, which applies to all Air Tractor, Inc. (Air Tractor) Models AT-300, AT-301, AT-302, and AT-400A airplanes that have aluminum spar caps; certain Air Tractor Models AT-400 airplanes that have aluminum spar caps; and all Models AT-300 and AT-301 airplanes that have aluminum spar caps and are or have been converted to turbine power. AD 2003-06-01 requires replacing the wing spar lower caps at a specified safe life limit; allows extending the safe life limit on certain airplanes if a wing lower spar cap splice rework is done; allows a limited time of continued operation beyond the safe life limit provided parts are ordered, the replacement is scheduled, and repetitive inspections reveal no cracks; and requires a report of any cracks found during any inspection to the FAA. This AD results from a recent report of cracks found on a Model AT-301 airplane at hours below the modification time specified in AD 2003-06-01. Consequently, this AD retains the wing spar lower cap replacement and reporting requirements from AD 2003-06-01 and adds a repetitive eddy-current inspection. We are issuing this AD to detect and correct cracks in the wing centerline splice joint. If not detected and corrected, these cracks could result in the wing separating from the airplane during flight.
AD 2008-08-11 · published Apr 28, 2008, effective Jun 2, 2008
MD Helicopters, Inc. Model MD900 Series Helicopters
This amendment adopts a new airworthiness directive (AD) for MD Helicopters, Inc. (MDHI) Model MD900 series helicopters that requires modifying the pilot and co-pilot dual-control directional pedal assemblies, or the pilot single-control directional pedal assembly (directional control pedal assembly). This amendment is prompted by an accident which has been attributed to loss of directional control due to failure of the welds in the directional control pedal assembly. The actions specified by this AD are intended to prevent fatigue cracking in the welds that connect the directional control pedal to the pedal shaft, resulting in loss of directional control and subsequent loss of control of the helicopter.
AD 2008-09-03 · published Apr 28, 2008, effective May 13, 2008
Agusta S.p.A. Model A109A, A109A II, and A109C Helicopters
We are adopting a new airworthiness directive (AD) for the specified Agusta S.p.A. (Agusta) model helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The European Aviation Safety Agency (EASA), the Technical Agent for Italy, with which we have a bilateral agreement, states in the MCAI:
AD 2008-08-14 · published Apr 14, 2008, effective Apr 29, 2008
Lycoming Engines IO, (L)IO, TIO, (L)TIO, AEIO, AIO, IGO, IVO, and HIO Series Reciprocating Engines, Teledyne Continental Motors (TCM) TSIO-360-RB Reciprocating Engines, and Superior Air Parts, Inc. IO-360 Series Reciprocating Engines With Certain Precision Airmotive LLC RSA-5 and RSA-10 Series Fuel Injection Servos
This document publishes in the Federal Register an amendment adopting emergency airworthiness directive (AD) 2008-06-51 that was sent previously to all known U.S. owners and operators of Lycoming Engines IO, (L)IO, TIO, (L)TIO, AEIO, AIO, IGO, IVO, and HIO series reciprocating engines, TCM TSIO-360-RB reciprocating engines, and Superior Air Parts, Inc. IO-360 series reciprocating engines with certain Precision Airmotive LLC RSA-5 and RSA-10 series fuel injection servos. This AD results from eighteen reports of fuel injection servo plugs, part number (P/N) 383493, that had loosened or completely backed out of the threaded plug hole on the regulator cover of the fuel injection servo. These servo plugs were installed with servo plug gasket, P/N 365533, under the plug hex-head. We are issuing this AD to prevent a lean running engine, which could result in a substantial loss of engine power and subsequent loss of control of the airplane.
AD 2008-06-52 · published Apr 15, 2008, effective Apr 30, 2008
Thielert Aircraft Engines GmbH (TAE) Model TAE 125-02-99 Engines
This document publishes in the Federal Register an amendment adopting emergency airworthiness directive (AD) 2008-06-52 that was sent previously to all known U.S. owners and operators of certain TAE Model TAE 125-02-99 engines. This AD requires, before further flight, replacing the high-pressure fuel line and installing a high-pressure fuel line support. This AD results from reports of in-flight engine shutdown incidents on airplanes equipped with TAE 125-02-99 engines. We are issuing this AD to prevent an in-flight engine shutdown or engine fire due to a cracked fuel line.
AD 2008-08-16 · published Apr 16, 2008, effective May 21, 2008
Turbomeca Makila 1A and 1A1 Turboshaft Engines
The FAA is superseding an existing airworthiness directive (AD) for Turbomeca Makila 1A, 1A1, and 1A2 turboshaft engines. That AD currently requires replacing certain digital electronic control units (DECUs) and electronic control units (ECUs) with modified DECUs and ECUs. This AD applies only to Makila 1A and 1A1 turboshaft engines, and requires replacing the selector-comparator board in the ECU with a board incorporating Turbomeca modification TU 250. This AD results from recent unexplained reversions of the ECU to the 65% N1 back-up mode. We are issuing this AD to prevent dual-engine continued operation at 65% N1 after reversion of the ECU to the 65% N1 back-up mode due to temporary loss of N2 speed signal, which could lead to inability to continue safe flight, emergency autorotation landing, or an accident.
AD 2008-08-01 · published Apr 14, 2008, effective May 19, 2008
McCauley Propeller Systems Propeller Models B5JFR36C1101/114GCA-0, C5JFR36C1102/L114GCA-0, B5JFR36C1103/114HCA-0, and C5JFR36C1104/L114HCA-0
The FAA is superseding three existing airworthiness directives (ADs) for McCauley Propeller Systems propeller models B5JFR36C1101/ 114GCA-0, C5JFR36C1102/L114GCA-0, B5JFR36C1103/114HCA-0, and C5JFR36C1104/L114HCA-0. Those ADs currently require fluorescent penetrant inspections (FPI) and eddy current inspections (ECI) of propeller blades for cracks, and if any crack indications are found, removing the blade from service. This AD requires the same initial inspections, but extends the compliance times and intervals, adds repetitive inspections, and mandates a life limit for the blades. This AD results from our determination that we must require repetitive inspections for cracks, and from reports of blunt leading edges of the propeller blades due to erosion. We are issuing this AD to detect cracks in the propeller blade that could cause failure and separation of the propeller blade and loss of control of the airplane, and to detect blunt leading edges on the propeller blades, which could cause airplane single engine climb performance degradation and could result in an increased risk of collision with terrain.
AD 2008-06-28 R1 · published Apr 14, 2008, effective Apr 10, 2008
Avidyne Corporation Primary Flight Displays (Part Numbers 700-00006-000, -001, -002, -003, and -100)
The FAA is adopting a new airworthiness directive (AD) to revise AD 2008-06-28, which applies to certain Avidyne Corporation (Avidyne) Primary Flight Displays (PFDs) (Part Numbers (P/Ns) 700- 00006-000, -001, -002, -003, and -100) that are installed on airplanes. AD 2008-06-28 currently requires you to do a check of the maintenance records and inspection of the PFD (if necessary) to determine if an affected serial number PFD is installed. If an affected serial number PFD is installed, this AD requires you to incorporate information that limits operation when certain conditions for the PFD or backup instruments exist. Since we issued AD 2008-06-28, we have learned that there is an incorrect serial number (SN) listed in AD 2008-06-28. Consequently, this AD retains the actions of AD 2008-06-28 and corrects the incorrect serial number. We are issuing this AD to prevent certain conditions from existing when PFDs display incorrect attitude, altitude, and airspeed information. This could result in airspeed/ altitude mismanagement or spatial disorientation of the pilot with consequent loss of airplane control, inadequate traffic separation, or controlled flight into terrain.
AD 2008-08-17 · published Apr 21, 2008, effective May 6, 2008
Kelly Aerospace Power Systems Turbochargers
The FAA is adopting a new airworthiness directive (AD) for certain Kelly Aerospace Power Systems turbochargers. This AD requires a onetime visual inspection of suspect turbochargers for an excessive gap between the turbocharger turbine housing flange and the exhaust tube flange, and replacement of turbochargers that fail the gap inspection. This AD results from two reports of exhaust leakage occurring between the turbocharger turbine housing flange and the exhaust tube flange due to machining defects of the turbocharger turbine housing flange. We are issuing this AD to prevent hazardous amounts of carbon monoxide from entering the cabin, an increase in under-cowl temperatures hampering engine and accessory function, and loss of tailpipe retention, which could lead to an in-flight fire and loss of control of the airplane.
