41 Airworthiness Directives: 28 airplane, 2 rotorcraft, 7 engine, 3 glider, 1 various.
AD 2006-16-02 · published Aug 3, 2006, effective Sep 7, 2006
McDonnell Douglas Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9- 83 (MD-83), DC-9-87 (MD-87), and MD-88 airplanes. This AD requires installing a clamp, a bonding jumper assembly, and attaching hardware to the refueling manifold in the right wing refueling station area. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent arcing on the in-tank side of the fueling valve during a lightning strike, which could result in an ignition source that could ignite fuel vapor and cause a fuel tank explosion.
AD 2006-16-03 · published Aug 3, 2006, effective Sep 7, 2006
McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A and KDC-10), DC-10-40, and DC-10-40F Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas airplanes, identified above. This AD requires installing or replacing with improved parts, as applicable, the bonding straps between the metallic frame of the fillet and the wing leading edge ribs, on both the left and right sides of the airplane. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to reduce the potential of ignition sources inside fuel tanks in the event of a severe lightning strike, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2006-16-08 · published Aug 8, 2006, effective Aug 23, 2006
Aerospatiale Model ATR42 and ATR72 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Aerospatiale Model ATR42 and ATR72 airplanes. This AD requires an inspection of the locking bolt of the upper attachment pin of the shock absorber on both main landing gears (MLGs) for the correct installation of the locking bolt and for any missing locking bolt, washer, nut, cotter pin, or compound, and applicable corrective action if necessary. This AD results from a report of migration and subsequent rupture of the attachment pin of the shock absorber of a MLG. We are issuing this AD to prevent failure of a MLG, which could result in significant structural damage to the airplane and possible injury to the occupants.
AD 2006-16-07 · published Aug 9, 2006, effective Aug 9, 2006
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires inspecting contactors 1K4XD, 2K4XD, and K4XA to determine the type of terminal base plate, and applying sealant on the terminal base plates, if necessary. This AD results from incidents of short circuit failures of certain alternating current (AC) contactors located in the avionics bay. We are issuing this AD to prevent short circuit failures of certain AC contactors, which could result in arcing and consequent smoke or fire.
AD 2006-16-09 · published Aug 9, 2006, effective Sep 13, 2006
McDonnell Douglas Model MD-90-30 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all McDonnell Douglas Model MD-90-30 airplanes. This AD requires installing a clamp, bonding jumper assembly, and attaching hardware to the refueling manifold in the right wing refueling station area. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent arcing on the in-tank side of the fueling valve during a lightning strike, which could result in an ignition source that could ignite fuel vapor and cause a fuel tank explosion.
AD 2006-16-10 · published Aug 9, 2006, effective Sep 13, 2006
Boeing Model 747-200B, 747-200C, 747-200F, 747-300, and 747SR Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-200B, 747-200C, 747-200F, 747-300, and 747SR series airplanes. This AD requires doing repetitive inspections of engine struts 1 through 4, as applicable, for heat discoloration, cracking, buckling, or wrinkling. This AD also requires doing a conductivity test to detect the extent of the heat damage and an inspection to detect cracking of the heat-discolored, buckled, or wrinkled area; and repair; if necessary. This AD results from reports of heat damage and cracking of the skin and internal structure adjacent to and aft of the precooler exhaust vent on several engine struts. We are issuing this AD to detect and correct cracking, buckling, wrinkling, or heat damage of the skin and internal structure of the engine struts, which could result in extensive damage to the engine struts and consequent possible separation of an engine from the airplane during flight.
AD 2006-16-11 · published Aug 9, 2006, effective Sep 13, 2006
Boeing Model 737-700 and 737-800 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-700 and 737-800 series airplanes. This AD requires performing a one-time high frequency eddy current inspection for cracking of the backup intercostals located above the cutout for the forward airstair door; doing related investigative and corrective actions if any crack is found; and doing other specified corrective actions if no crack is found. This AD results from a report of fatigue cracks discovered during a full-scale fatigue test conducted by the manufacturer. We are issuing this AD to detect and correct such cracking, which could result in more extensive fatigue cracking and lead to possible loss of cabin pressure.
AD 2006-16-12 · published Aug 9, 2006, effective Sep 13, 2006
McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-30, DC-10-30F (KDC-10), DC-10-40, and DC-10-40F Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas airplanes, identified above. This AD requires reducing the length of the sump drain collar and replacing the fuel tank sump drain lockring for fuel tanks 1, 2, and 3; and reducing the length of the drain outlet barrel for the auxiliary fuel tank, if applicable. For airplanes with an auxiliary fuel tank, this AD also requires relocating the sump drain outlet to allow draining the sumps without opening the doors of the main landing gear wheel well. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to reduce the potential of ignition sources inside fuel tanks in the event of a lightning strike, which, in combination with flammable fuel vapors, could result in arcing in the fuel tank, fuel tank explosions, and consequent loss of the airplane.
AD 2006-16-13 · published Aug 14, 2006, effective Sep 18, 2006
Pilatus Aircraft Ltd. Models PC-12 and PC-12/45 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2006-16-19 · published Aug 14, 2006, effective Sep 18, 2006
B-N Group Ltd. BN-2, BN-2A, BN-2B, BN-2T, and BN-2T-4R Series (All Individual Models Included in Type Certificate Data Sheet (TCDS) A17EU, Revision 16, Dated December 9, 2002) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. We are issuing this AD to require actions to correct the unsafe condition on these products.
AD 2006-16-14 · published Aug 18, 2006, effective Sep 22, 2006
Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A318, A319, A320, and A321 airplanes. This AD requires inspecting to determine the part number of the twin motor actuators, and related investigative and corrective actions if necessary. This AD results from a report of a low pressure valve of the twin motor actuator found partially open, although the valve detection system indicated that the valve was closed. Investigation revealed that the locating pin in the actuator was too short to engage with the valve slot, resulting in incorrect alignment of the actuator and the drive assembly, causing the valve to remain partially open. We are issuing this AD to ensure that, in the event of an engine fire, the valve actuator functions properly to block the fuel flow to the engine and prevent an uncontrollable fire.
AD 2006-16-15 · published Aug 18, 2006, effective Sep 22, 2006
McDonnell Douglas Model MD-10-10F and MD-10-30F Airplanes and Model MD-11 and MD-11F Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain McDonnell Douglas Model MD-11 series airplanes. That AD currently requires a revision of the airplane flight manual (AFM) to alert the flightcrew that both flight management computers (FMCs) must be installed and operational. That AD also requires an inspection to determine the serial number of the FMCs; and follow- on corrective actions, if necessary, which terminate the AFM revision. That AD also requires an inspection to verify if a certain modification is on the identification plates of the FMCs; and applicable follow-on and corrective actions. This new AD requires installation of upgraded FMC software, which would terminate the existing AD. This new AD also adds airplanes to the applicability, including adding Model MD-10-10F and MD-10-30F airplanes. This AD results from a report that the FMC does not acknowledge the pre-set glareshield control panel (GCP) altitude when profile (PROF) mode is engaged in descent mode. We are issuing this AD to prevent the un-commanded descent of an airplane below the selected level-off altitude, which could result in an unacceptable reduction in the separation between the airplane and nearby air traffic or terrain.
AD 2006-16-16 · published Aug 18, 2006, effective Sep 22, 2006
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-135BJ airplanes. This AD requires inspecting for missing fire blocking material on the left- and right-hand partitions of the forward baggage compartment door; replacing the seal on both partitions; and performing corrective action if necessary. This AD results from a report indicating that certain airplanes were delivered with the fire blocking material missing and the seal improperly installed on the partitions of the forward baggage compartment door. We are issuing this AD to detect and correct such discrepancies on the forward baggage compartment partition, which, in the event of a fire in the baggage compartment, could result in smoke propagating into the main cabin.
AD 2006-17-01 · published Aug 18, 2006, effective Sep 22, 2006
Mitsubishi Heavy Industries MU-2B Series Airplanes
The FAA adopts a new airworthiness directive (AD) for all Mitsubishi Heavy Industries (MHI) MU-2B series airplanes. This AD requires you to incorporate power assurance charts into the Limitations Section of the Airplane Flight Manual (AFM), inspect the engine torque indication system, and recalibrate the torque pressure transducers as required. This AD results from a recent safety evaluation that used a data-driven approach to analyze the design, operation, and maintenance of the MU-2B series airplanes in order to determine their safety and define what steps, if any, are necessary for their safe operation. Part of that evaluation was the identification of unsafe conditions that exist or could develop on the affected type design airplanes. We are issuing this AD to detect and correct torque transducers that are out of calibration. The above issue, if uncorrected, could result in degraded performance and poor handling qualities with consequent loss of control of the airplane in certain situations.
AD 2006-17-04 · published Aug 18, 2006, effective Sep 1, 2006
The Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to inspect the two end fittings on each of the flexible fuel hoses located in the engine compartment for the correct torque values, and, if any incorrect torque values are found during the inspection, tighten the hose end fittings to the correct torque values. This AD results from one report of loose fuel hose connections to the fuel injector servo on a Cessna Model 172S airplane. We are issuing this AD to detect and correct any incorrect torque values of the end fittings of flexible fuel hoses in the engine compartment, which could result in the loss of fuel flow and fuel leakage. Loss of fuel flow could result in partial or complete loss of engine power and fuel leakage could result in an engine compartment fire.
AD 2006-17-05 · published Aug 18, 2006, effective Sep 22, 2006
Mitsubishi Heavy Industries MU-2B Series Airplanes
The FAA adopts a new airworthiness directive (AD) for all Mitsubishi Heavy Industries (MHI) MU-2B series airplanes. This AD requires you to do flight checks of the rigging of the engine and propeller systems. This AD results from a recent safety evaluation that used a data-driven approach to evaluate the design, operation, and maintenance of the MU-2B series airplanes in order to determine their safety and define what steps, if any, are necessary for their safe operation. Part of that evaluation was the identification of unsafe conditions that exist or could develop on the affected type design airplanes. We are issuing this AD to detect and correct improper adjustment of the flight idle fuel flow setting. This condition, if uncorrected, could result in degraded performance and poor handling qualities with consequent loss of control of the airplane in certain situations.
AD 2006-16-17 · published Aug 21, 2006, effective Sep 25, 2006
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135BJ, -135ER, -135KE, -135KL, and -135LR Airplanes; and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-135 and -145 series airplanes. This AD requires determining the torque values of the screws that attach the seat tracks to the airplane, and corrective action if necessary. This AD results from a report of undertorqued screws. We are issuing this AD to prevent improper torque of those screws, which in the case of a hard landing or a high deceleration impact condition could result in damage to the seat and possible subsequent injury to the passenger.
AD 2006-17-06 · published Aug 21, 2006, effective Sep 5, 2006
Aerospatiale Model ATR42-500 Airplanes and Model ATR72-212A Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Aerospatiale Model ATR42-500 and ATR72- 212A series airplanes, that requires repetitive inspections for cracking of the upper closing rib of the vertical fin, related investigative actions, and corrective actions if necessary. This new AD requires modifying the installation of the vertical leading edge fairing at the fin tip, which ends the repetitive inspections. This AD results from a report that rudder operation difficulties occurred on a Model ATR42-500 series airplane while the airplane was on the ground. We are issuing this AD to prevent interference between the upper closing rib and the rudder, which could result in a rudder jam and consequent reduced controllability of the airplane.
AD 2006-17-09 · published Aug 22, 2006, effective Sep 6, 2006
Fokker Model F27 Mark 050 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F27 Mark 050 airplanes. This AD requires doing an initial inspection of the leading edge sections of the elevators to detect loose leading edges and to ensure that there is no gap between the sections and the front spar, and corrective actions if necessary. This AD also requires determining the type of leading edge installed on the elevators. For certain airplanes, this AD requires repetitive inspections until the modification of the leading edge sections of the elevators and the application of sealant, which would end the repetitive inspections. This AD results from reports that the leading edges of the elevators were found loose, although the fasteners were still in place; in one case a stud was broken. In addition, the fastener attachment holes were elongated and worn out, and fretting damage was found on the elevator front spar and balance weights. Investigation revealed that vibration, induced by the propeller slipstream, was the cause of these discrepancies; the stud failure was due to improper installation of the fasteners. We are issuing this AD to prevent jamming, restricting, or binding of the elevators due to loose or missing fasteners, which could make the movement of the elevator difficult and decrease aerodynamic control of the airplane.
AD 2006-17-10 · published Aug 23, 2006, effective Sep 27, 2006
Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 series airplanes. This AD requires repetitive inspections of the fluorescent light tube assemblies of the cabin, lavatory, and sidewall, and corrective actions if necessary. This AD also provides for optional terminating action for the repetitive inspections. This AD results from reports of overheating due to arcing between the fluorescent tube pins and the lamp holder contacts. The tubes had not been properly seated during installation. We are issuing this AD to prevent fumes, traces of visible smoke, and fire at the fluorescent light tube assembly.
AD 2006-17-11 · published Aug 23, 2006, effective Sep 27, 2006
Boeing Model 767-400ER Series Airplanes and Model 777-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-400ER series airplanes and Model 777-200 and - 300 series airplanes. This AD requires, for certain airplanes, repetitive testing of the fill and safety fittings of the cargo fire extinguishing bottles in the forward cargo compartment for leaks; and repetitive application of a corrosion inhibiting compound (CIC) or replacement of the cargo fire extinguishing bottles with reworked fire extinguishing bottles, as necessary. For all airplanes, this AD requires replacement of the cargo fire extinguishing bottles with reworked fire extinguishing bottles, which ends the repetitive tests and CIC applications if applicable. This AD results from failure of the safety fittings for the cargo fire extinguishing bottles. We are issuing this AD to prevent failure of the safety fittings for the cargo fire extinguishing bottles due to corrosion, which could result in leakage of extinguishing agent. If a fire occurs in the cargo bay, the cargo fire extinguishing bottles could have less than enough extinguishing agent to control a fire.
AD 2006-17-13 · published Aug 23, 2006, effective Sep 27, 2006
RECARO Aircraft Seating GmbH & Co. (RECARO) Model 3410 Seats
The FAA is adopting a new airworthiness directive (AD) for certain RECARO Model 3410 302, 303, 306, 307, 314, 316, 317, 791, 792, and 795 series seats. This AD requires replacing the existing attachment bolts for the seat belts with longer attachment bolts. This AD results from a report of short attachment bolts that don't allow enough thread to properly secure the locknuts. We are issuing this AD to prevent a seat belt from detaching due to a loose locknut and attachment bolt, which could result in injury to an occupant during emergency conditions.
AD 2006-17-14 · published Aug 23, 2006, effective Sep 7, 2006
Bombardier Inc. Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. The existing AD currently requires inspecting contactors 1K4XD, 2K4XD, and K4XA to determine the type of terminal base plate, and applying sealant on the terminal base plates, if necessary. This new AD revises the effective date of the existing AD. This AD results from incidents of short circuit failures of certain alternating current (AC) contactors located in the avionics bay. We are issuing this AD to prevent short circuit failures of certain AC contactors, which could result in arcing and consequent smoke or fire.
AD 2006-17-15 · published Aug 25, 2006, effective Sep 29, 2006
McDonnell Douglas Model DC-10-10 and DC-10-10F Airplanes; and Model MD-10-10F Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model DC-10-10 and DC-10-10F airplanes; and Model MD-10-10F airplanes. This AD requires replacing the clamp bases for the fuel vent pipe with improved clamp bases. This AD results from reports that the foil wrapping on existing plastic clamp bases has migrated out of position, which compromises the bonding of the fuel vent pipes to the airplane structure. We are issuing this AD to ensure that the fuel vent pipes are properly bonded to the airplane structure. Improper bonding could prevent electrical energy from a lightning strike from dissipating to the airplane structure, and create an ignition source, which could result in a fuel tank explosion.
AD 2006-17-16 · published Aug 25, 2006, effective Sep 29, 2006
Fokker Model F.28 Mark 0070 and 0100 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F.28 Mark 0070 and 0100 airplanes. This AD requires a one- time detailed inspection to detect corrosion on the wing rear spar lower girder, and related investigative and applicable corrective actions if necessary. This AD results from reports of corrosion of the wing rear spar lower girder between wing station (STA) 8700 and wing STA 9200. We are issuing this AD to detect and correct corrosion of the wing rear spar lower girder, which could result in reduced structural integrity of the wing rear spar.
AD 2006-17-17 · published Aug 25, 2006, effective Sep 29, 2006
Bombardier Model DHC-8-100, DHC-8-200, DHC-8-300, and DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-100, DHC-8-200, DHC-8-300, and DHC-8-400 series airplanes. This AD requires inspecting the left and right control column torque tube assemblies to determine the type of rivets installed and replacing incorrect or indeterminate type rivets with the correct type rivets. This AD results from a report that incorrect rivets having lower than required strength were installed on the control column torque tube during production. We are issuing this AD to prevent shear failure of control column torque tube rivets, which could cause unexpected decoupling of the elevators and large unwanted deflection of the free elevator, and consequent reduced controllability of the airplane.
AD 2006-18-02 · published Aug 30, 2006, effective Oct 4, 2006
McDonnell Douglas Model DC-9-10, -20, -30, -40, and -50 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all McDonnell Douglas Model DC-9-10, -20, -30, -40, and -50 series airplanes. This AD requires replacing the clamp bases for the fuel vent pipe with improved clamp bases. This AD results from reports that the foil wrapping on existing plastic clamp bases has migrated out of position, which compromises the bonding of the fuel vent lines to the airplane structure. We are issuing this AD to ensure that the fuel vent lines are properly bonded to the airplane structure. Improper bonding could prevent electrical energy from a lightning strike from dissipating to the airplane structure, and create an ignition source, which could result in a fuel tank explosion.
AD 2006-18-03 · published Aug 30, 2006, effective Oct 4, 2006
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-145XR Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-145XR airplanes. This AD requires modification of the flap system interface wiring. This AD results from a finding that the aural and visual warnings, which should be activated when the flaps are set to 22 degrees during takeoff, were not enabled during the manufacture of certain Model EMB-145XR airplanes. We are issuing this AD to prevent overrunning the runway during takeoff.
AD 2006-15-19 · published Aug 1, 2006, effective Aug 16, 2006
Sikorsky Aircraft Corporation Model S-92A Helicopters
This amendment adopts a new airworthiness directive (AD) for the Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopters. This action requires, before further flight, replacing a certain main gearbox (MGB) upper main housing assembly (housing assembly) that has 2700 or more hours time-in-service (TIS) with an airworthy part. This action also requires, before further flight, revising the Airworthiness Limitations section (ALS) of the maintenance manual by establishing a new retirement life for the MGB housing assembly of 2700 hours TIS. This amendment is prompted by testing of the MGB housing assembly that resulted in premature fatigue failure due to a manufacturing process creating an oxide skin defect in the housing. The actions specified in this AD are intended to prevent fatigue failure of the MGB housing, loss of MGB lube oil, loss of main and tail rotor drive, and subsequent loss of control of the helicopter.
AD 2006-18-01 · published Aug 29, 2006, effective Oct 3, 2006
MD Helicopters, Inc. Model MD900 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for MD Helicopters, Inc. (MDHI) Model MD900 helicopters, that currently requires reducing the life limit of certain Notar fan system tension-torsion (TT) straps. That existing AD also requires, at a specified time interval, removing each affected TT strap from the helicopter, doing a visual and X-ray inspection, and replacing any unairworthy part before further flight. This amendment requires the same actions as the existing AD, but also requires revising the life limit on the component history card or equivalent record and doing repetitive visual and X-ray inspections, and removes reporting requirements. This amendment is prompted by two in-flight TT strap failures. The actions specified by this AD are intended to prevent failure of a TT strap, loss of directional control, and subsequent loss of control of the helicopter.
AD 2006-16-04 · published Aug 3, 2006, effective Sep 7, 2006
Rolls-Royce Corporation (Formerly Allison Engine Company, Allison Gas Turbine Division, and Detroit Diesel Allison) (RRC) 250-B and 250-C Series Turboshaft and Turboprop Engines
The FAA is superseding an existing airworthiness directive (AD) for RRC 250-B and 250-C series turboshaft and turboprop engines. That AD currently requires a onetime inspection of the fuel nozzle screen for contamination, and if contamination is found, inspection and cleaning of the entire aircraft fuel system before further flight. That AD also requires replacing the fuel nozzle with a new design fuel nozzle, at the next fuel nozzle overhaul or by June 30, 2006, whichever occurs first. This AD requires the same actions, but would add additional part numbers (P/Ns) to the list of affected fuel nozzles. This AD would also explain that the existing AD, as worded, allows certain part number (P/N) fuel nozzles back into service. Those fuel nozzles must not be allowed back into service. This AD is prompted by the discovery that several P/Ns of fuel nozzles were inadvertently left out of AD 2004-24-09. We are issuing this AD to minimize the risk of sudden loss of engine power and uncommanded shutdown of the engine due to fuel contamination and collapse of the screen in the fuel nozzle.
AD 2006-16-05 · published Aug 4, 2006, effective Sep 8, 2006
Pratt & Whitney PW4164, PW4168, and PW4168A Series Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Pratt & Whitney PW4164, PW4168, and PW4168A series turbofan engines. That AD currently requires initial and repetitive torque checks for loose or broken front pylon mount bolts made from INCO 718 material and MP159 material, and initial and repetitive visual inspections of the primary mount thrust load path. This AD requires the same actions, but at reduced intervals for front pylon mount bolts made from MP159 material. This AD results from analysis by the manufacturer that the MP159 material pylon bolts do not meet the full life cycle torque check interval requirement, in a bolt-out condition. We are issuing this AD to prevent front pylon mount bolt and primary mount thrust load path failure, which could result in an engine separating from the airplane.
AD 2006-02-08 R1 · published Aug 14, 2006, effective Sep 13, 2006
Turbomeca S.A. Engines
The FAA is revising an existing airworthiness directive (AD) for certain Turbomeca Arriel 1B, 1D, 1D1, and 1S1 turboshaft engines. That AD currently requires initial and repetitive position checks of the gas generator 2nd stage turbine blades on all Turbomeca Arriel 1B, 1D, 1D1, and 1S1 turboshaft engines. That AD also currently requires initial and repetitive replacements of 2nd stage turbines on 1B, 1D, and 1D1 engines only. This AD revision requires the same actions, but would relax the compliance times for initially replacing 2nd stage turbines in Arriel 1B, 1D, and 1D1 turboshaft engines. We are issuing this AD revision to clarify and relax the AD compliance times for 2nd stage turbine initial replacement on Arriel 1B, 1D, and 1D1 turboshaft engines. We are also issuing this AD revision to prevent in-flight engine shutdown and subsequent forced autorotation landing or accident. DATES: This AD becomes effective September 13, 2006. The Director of the Federal Register previously approved the incorporation by reference of certain publications listed in the regulations as of February 28, 2006 (71 FR 3754, January 24, 2006).
AD 2006-16-06 · published Aug 18, 2006, effective Sep 5, 2006
General Electric Company (GE) CF6-80 Series Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for GE CF6-80 series turbofan engines with certain stage 1 high- pressure turbine (HPT) rotor disks. That AD currently requires an initial inspection as a qualification for the mandatory rework procedures for certain disks, and repetitive inspections only for certain disks for which the rework procedures were not required. That action also requires reworking certain disks before further flight, and removes certain CF6-80E1 series disks from service. This AD requires the same actions but shortens the compliance schedule for HPT disks that have not been previously inspected using AD 2004-04-07, which this AD supersedes. This AD results from a recent report of an uncontained failure of a stage 1 HPT disk. We are issuing this AD to detect and prevent cracks in the bottoms of the dovetail slots that could propagate to failure of the disk and cause an uncontained engine failure.
AD 2006-17-08 · published Aug 23, 2006, effective Sep 27, 2006
Pratt & Whitney PW4077D, PW4084D, PW4090, and PW4090-3 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Pratt & Whitney (PW) PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engines that were reassembled with certain previously used high pressure compressor (HPC) exit brush seal assembly parts and certain new or refurbished HPC exit diffuser air seal inner lands. This AD requires replacing the HPC exit inner and outer brush seal packs with new brush seal packs, or replacing the HPC exit brush seal assembly with a new HPC exit brush seal assembly. This AD results from a report of oil leaking into the high pressure turbine (HPT) interstage cavity and igniting, leading to an engine case penetration and engine in- flight shutdown. Although liberated engine parts did not penetrate the engine nacelle, we are issuing this AD to prevent uncontained engine failure, damage to the airplane, and injury to passengers.
AD 2006-17-12 · published Aug 23, 2006, effective Sep 27, 2006
Rolls-Royce plc RB211 Series Turbofan Engines
This amendment supersedes an existing airworthiness directive (AD), that is applicable to Rolls-Royce plc (RR) models RB211-535E4-37, RB211-535E4--37, RB211-535C-37, RB211-535E4-B-75, RB211-535E4-C, and RB211-22B-02 turbofan engines. That AD currently requires inspecting certain high pressure (HP) turbine discs, manufactured between 1989 and 1999, for cracks in the rim cooling air holes, and, if necessary, replacing the discs with serviceable parts. The manufacturer identified reaming-induced machining anomalies (RIMA) as the cause for the cracking. This amendment requires the same inspections, and reduces the compliance times for eddy current inspection (ECI) for the RR RB211- 22B-02 engines. This amendment results from the manufacturer reducing their recommended compliance times for inspections on RB211-22B-02 engines. We are issuing this AD to prevent possible disc failure, which could result in an uncontained engine failure and damage to the airplane.
AD 2006-17-07 · published Aug 30, 2006, effective Oct 4, 2006
Pratt & Whitney JT8D-1, -1A, -1B, -7, -7A, -7B, -9, -9A, -11, -15, -15A, -17, -17A, -17R, -17AR, -209, -217, -217A, -217C, and -219 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-209, -217, -217A, -217C, and -219 turbofan engines. That AD currently requires initial and repetitive visual inspections for fretting and fluorescent magnetic particle inspections (FMPI) for cracking in the area of the tierod holes on 8th stage high pressure compressor (HPC) front hubs (from here on, referred to as HPC front hubs) that have operated at any time with PWA 110-21 coating. This AD requires either replacing HPC front hubs and HPC disks that have operated at any time with PWA 110-21 coating and that operated in certain engine models, or, visually inspecting and FMPI for cracking of those parts and re-plating them if they pass inspection. This AD also requires adding JT8D-1, -1A, -1B, -7, -7A, -7B, -9, -9A, - 11, -15, -15A, -17, -17A, -17R, and -17AR engines to the applicability. This AD results from an investigation by PW, which concluded that any HPC front hub or HPC disk coated with PWA 110-21 that ever operated on JT8D-15, -15A, -17, -17A, -17R, -17AR, -209, -217, -217A, -217C, and - 219 turbofan engines, could crack before reaching their published life limit. We are issuing this AD to prevent a rupture of an HPC front hub or an HPC disk that could result in an uncontained engine failure and damage to the airplane.
AD 2006-16-20 · published Aug 14, 2006, effective Sep 18, 2006
DG Flugzeugbau GmbH Model DG-1000S Sailplanes
We are adopting a new airworthiness directive (AD) for all DG Flugzeugbau GmbH Model DG-1000S sailplanes. This AD requires you to modify the elevator control at the stabilizer assembly, replace a placard on the fin, and incorporate changes in the FAA-approved sailplane flight manual (SFM). This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to prevent the rigging of the horizontal stabilizer without properly connecting the elevator, which, if not prevented, could lead to an inoperative elevator. An inoperative elevator could lead to loss of control of the sailplane.
AD 2006-17-02 · published Aug 18, 2006, effective Sep 22, 2006
GROB-WERKE GMBH & CO KG Model G102 ASTIR CS Sailplanes
The FAA supersedes Airworthiness Directive (AD) 84-09-05, which applies to certain GROB-WERKE GMBH & CO KG (previously identified as BURKHART-GROB FLUGZEUGBAU INDUSTRIESTRABE) Model G102 ASTIR CS sailplanes. AD 84-09-05 requires you to install a modified spherical locking bolt and nut in the forward horizontal stabilizer connection to the vertical stabilizer and install new locking pins in the aft connecting plate for the horizontal stabilizer. Since we issued AD 84- 09-05, fatigue cracks were found in the modified spherical locking bolt. Consequently, this AD requires you to replace the modified spherical locking bolt, the retaining pins (collar bolts), and associated hardware; add a life limit on the spherical locking bolt and the retaining pins; and repetitively inspect the front and rear horizontal stabilizer attachment. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to prevent cracks in the spherical locking bolt, which could result in failure of the horizontal stabilizer connection. This failure could lead to loss of control.
AD 2006-17-03 · published Aug 18, 2006, effective Sep 22, 2006
Stemme GmbH & Co. KG Models S10, S10-V, and S10-VT Sailplanes
The FAA adopts a new airworthiness directive (AD) for certain Stemme GmbH & Co. KG (Stemme) Models S10, S10-V, and S10-VT sailplanes. This AD requires you to inspect the connection between the aileron push-rod and the connecting shaft to determine if a safety washer is installed. If there is no safety washer installed, this AD requires you to modify the aileron control assembly. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to prevent a loose bearing in the aileron control lever, which could result in separation of the aileron control system. Separation of the aileron control system could lead to loss of aileron control.
AD 2006-16-18 · published Aug 21, 2006, effective Sep 25, 2006
Sandel Avionics Incorporated Model ST3400 Terrain Awareness Warning System/Radio Magnetic Indicator (TAWS/RMI) Units Approved Under Technical Standard Order(s) C113, C151a, or C151b; Installed on Various Small and Transport Category Airplanes
The FAA is adopting a new airworthiness directive (AD). The new AD is for Sandel Avionics Incorporated Model ST3400 TAWS/RMI units as described above. This AD requires installing a warning placard on the TAWS/RMI and revising the Limitations section of the airplane flight manual (AFM). This AD also requires installing upgraded software in the TAWS/RMI. This AD results from a report that an in-flight bearing error occurred in a Model ST3400 TAWS/RMI configured to receive bearing information from a very high frequency omnidirectional range (VOR) receiver interface via a composite video signal, due to a combination of input signal fault and software error. We are issuing this AD to prevent a bearing error, which could lead to an airplane departing from its scheduled flight path, which could result in a reduction in separation from, and a possible collision with, other aircraft or terrain.
