35 Airworthiness Directives: 28 airplane, 1 rotorcraft, 2 engine, 2 propeller, 1 appliance, 1 glider.
AD 2005-22-11 · published Nov 1, 2005, effective Dec 6, 2005
Mitsubishi Model YS-11 Airplanes, and Model YS-11A-200, YS-11A-300, YS-11A-500, and YS-11A-600 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Mitsubishi Model YS-11 airplanes, and Model YS- 11A-200, YS-11A-300, YS-11A-500, and YS-11A-600 series airplanes. This AD requires repetitive removal of the spinner; repetitive detailed inspections of the propeller hub to detect fatigue cracking; and replacement of a propeller hub with a new propeller hub, if necessary. This action is necessary to detect and correct fatigue cracking of the propeller hub, which could cause the loss of the propeller. This action is intended to address the identified unsafe condition.
AD 2005-22-13 · published Nov 3, 2005, effective Dec 19, 2005
Pilatus Aircraft Ltd. Models PC-12 and PC-12/45 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Pilatus Aircraft Ltd. (Pilatus) Models PC-12 and PC-12/45 airplanes. This AD requires you to inspect the left and right main landing gear (MLG) assemblies for any part number (P/N) 532.10.12.077 or FAA- approved equivalent part number bolts that do not have white primed and painted heads; and replace any bolt found with new P/N 532.10.12.077F or FAA-approved equivalent part number bolts in all MLG assemblies. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. We are issuing this AD to detect and correct any P/N 532.10.12.077 or FAA- approved equivalent part number bolts that do not have white primed and painted heads, which could result in corrosion of the bolt and consequent failure of the bolt. This failure could lead to MLG collapse during airplane landing and take-off operations with consequent loss of airplane control.
AD 2005-22-14 · published Nov 3, 2005, effective Dec 19, 2005
GROB-WERKE Model G120A Airplanes
The FAA adopts a new airworthiness directive (AD) for all GROB-WERKE Model G120A airplanes. This AD requires you to inspect for signs of any chafing damage to the attachment cables of the switch panels below the left-hand instrument panel, any damaged switch below the switch panels of the left-hand instrument panel, any damaged (that is, sharp) edge of the support tray for the attachment cables of the switch panels below the left-hand instrument panel; correct any damage found during the inspection; and apply a layer of anti-rub (protective padding) strips to the edge of the support tray. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to detect, correct, and prevent chafing of the cables against the rear lip of the tray that holds the switch panels. Chafing of the electrical cables could result in smoke or fire in the cockpit.
AD 2005-23-07 · published Nov 8, 2005, effective Dec 13, 2005
Boeing Model 727 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 727 airplanes. This AD requires revising the Limitations section of the airplane flight manual to prohibit resetting a tripped circuit breaker for a fuel pump. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prohibit the resetting of a tripped circuit breaker for a fuel pump, which could allow an electrical fault to override the protective features of the circuit breaker, and could result in sparks inside the fuel tank, ignition of fuel vapors, and consequent fire or explosion.
AD 2005-23-01 · published Nov 14, 2005, effective Nov 29, 2005
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness of the Canadair Regional Jet Maintenance Requirements Manual by incorporating new procedures for repetitive detailed and special detailed inspections for cracking of the aft pressure bulkhead. This AD results from a fatigue test, which revealed cracking of the aft pressure bulkhead; subsequent in-service reports show that fatigue cracking has been found on other airplanes. We are issuing this AD to detect and correct cracking in the aft pressure bulkhead, which could result in reduced structural integrity and rapid decompression of the airplane.
AD 2005-23-02 · published Nov 14, 2005, effective Dec 19, 2005
Airbus Model A319-100 Series Airplanes, Model A320-111 Airplanes, Model A320-200 Series Airplanes, and Model A321-100 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A319-100 series airplanes, Model A320-111 airplanes, Model A320-200 series airplanes, and Model A321-100 series airplanes equipped with any additional center tank (ACT). This AD requires identifying the part number of the ACT and, for certain ACTs, replacing the outer ACT manhole cover and seal. This AD results from reports of an ACT fuel transfer failure due to air leakage around the seal of the outer manhole covers of the ACTs. We are issuing this AD to prevent this leakage, which could result in fuel or fuel vapor leaking into the cargo compartment, and consequent increased risk of a fire in the cargo compartment.
AD 2005-23-03 · published Nov 14, 2005, effective Dec 19, 2005
Learjet Model 23, 24, 24A, 24B, 24B-A, 24C, 24D, 24D-A, 24E, 24F, 24F-A, 25, 25A, 25B, 25C, 25D, and 25F Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Learjet Model 23, 24, 24A, 24B, 24B-A, 24C, 24D, 24D-A, 24E, 24F, 24F-A, 25, 25A, 25B, 25C, 25D, and 25F airplanes. This AD requires replacement of the spherical accumulator for the main hydraulic system with a new cylindrical accumulator. For certain airplanes, this AD also requires modification of the accumulator pressure gauge. This AD results from reports of the failure of two thrust reverser accumulators (which are similar to the main hydraulic system's spherical accumulator) and fatigue cracks found on four thrust reverser accumulators. We are issuing this AD to prevent failure of the spherical accumulator for the main hydraulic system, due to fatigue cracking on the threads, which could result in the loss of hydraulic power, damage to the surrounding airplane structure, and loss of airplane control. The failure of the accumulator could also result in injury to any persons in the surrounding area. The loss of hydraulic fluid could also leak onto a potential source of ignition and result in a consequent fire.
AD 2005-23-04 · published Nov 14, 2005, effective Dec 19, 2005
Saab Model SAAB 2000 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Saab Model SAAB 2000 airplanes. This AD requires modifying the manual feather-and-unfeather system for the propellers to make the design of the system more robust. This AD results from reports of in- flight engine shutdown caused by uncommanded operation of the feather pump of the propeller. We are issuing this AD to prevent uncommanded feathering of the propeller, which could result in the shutdown of an engine during flight and consequent reduced controllability of the airplane.
AD 2005-23-05 · published Nov 14, 2005, effective Dec 19, 2005
Airbus Model A319-100, A320-200, and A321-100 and -200 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A319-100, A320-200, and A321-100 and -200 series airplanes. That AD currently requires modification of the telescopic girt bar of the escape slide/raft assembly, and follow-on actions. This new AD requires a new modification of the telescopic girt bar and the installation of placards on the modified girt bars, which terminates the repetitive functional tests required by the existing AD. This AD results from development of a new, improved modification. We are issuing this AD to prevent failure of the escape slide/raft to deploy correctly, which could result in the slide being unusable during an emergency evacuation and consequent injury to passengers or airplane crewmembers.
AD 2005-23-06 · published Nov 14, 2005, effective Dec 19, 2005
Learjet Model 23, 24, 24A, 24B, 24B-A, 24D, 24D-A, 24E, 24F, 25, 25A, 25B, 25C, 25D, and 25F Airplanes Modified by Supplemental Type Certificate SA1731SW, SA1669SW, or SA1670SW
The FAA is adopting a new airworthiness directive (AD) for certain Learjet Model 23, 24, 24A, 24B, 24B-A, 24D, 24D-A, 24E, 24F, 25, 25A, 25B, 25C, 25D, and 25F airplanes. This AD requires removing the thrust reverser accumulator, and making the thrust reverser hydraulic system and the thrust reversers inoperable. This AD results from reports of the failure of two thrust reverser accumulators. We are issuing this AD to prevent failure of the thrust reverser accumulators, due to fatigue cracking on the female threads, which could result in the loss of hydraulic power and damage to the surrounding airplane structure.
AD 2005-23-08 · published Nov 14, 2005, effective Dec 19, 2005
Airbus Model A300 B4-600 and A300 B4-600R Series Airplanes; and A300 F4-605R and A300 C4-605R Variant F Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Airbus Model A300 B4-600 and A300 B4-600R series airplanes, and all Model A300 F4-605R airplanes. That AD currently requires repetitive inspections to detect cracks of certain attachment holes, installation of new fasteners, follow-on inspections or repair if necessary, and modification of the angle fittings of fuselage frame FR47. This new AD revises certain inspection thresholds and intervals. This new AD also adds inspections to detect cracks of additional attachment holes. This AD results from reports of cracks found before the inspection thresholds in the existing AD and cracks found in nearby areas not inspected by the existing AD. We are issuing this AD to prevent fatigue cracking of the forward fitting of fuselage frame FR47, which could result in reduced structural integrity of the frame.
AD 2005-23-10 · published Nov 14, 2005, effective Nov 29, 2005
Airbus Model A330-200 and A330-300 Series Airplanes; and Model A340-200 and A340-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A330-200 and A330-300 series airplanes; and Model A340-200 and A340-300 series airplanes. This AD requires an accelerated schedule of repetitive testing of the elevator servo control loops, and corrective actions if necessary. This AD results from reports of failed elevator servo controls due to broken guides. We are issuing this AD to ensure proper functioning of the elevator servo controls. Failure of the elevator servo controls during certain phases of takeoff could result in an unannounced loss of elevator control and consequent reduced controllability of the airplane.
AD 2005-23-13 · published Nov 14, 2005, effective Dec 19, 2005
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 Airplanes, and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-135 airplanes, and Model EMB-145, -145ER, - 145MR, -145LR, -145XR, -145MP, and -145EP airplanes. This AD requires modification of the logic of the steering system of the nose landing gear (NLG) wheel. This AD results from reports of the loss of directional control of the airplane on the ground after an internal failure of the NLG wheel steering system. We are issuing this AD to prevent failure of the NLG wheel steering system, which could result in reduced controllability of the airplane.
AD 2005-23-14 · published Nov 14, 2005, effective Nov 29, 2005
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 airplanes. This AD requires repetitively replacing the low-stage check valve and associated seals of the right-hand engine bleed system. This AD results from a report that an engine shut down during flight due to the failure of the low-stage check valve to close. We are issuing this AD to prevent failure of the low-stage check valve, which could result in an engine shutting down during flight.
AD 2005-23-15 · published Nov 16, 2005, effective Dec 21, 2005
British Aerospace Model BAC 1-11 200 and 400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all British Aerospace Model BAC 1-11 200 and 400 series airplanes. This AD requires revising the airplane flight manual (AFM) to contain applicable AFM amendments, which advise the flightcrew of information pertaining to safely operating the fuel system. The AD also requires revising the FAA-approved maintenance program to include certain repetitive maintenance tasks intended to improve the safety of the fuel system. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent potential ignition sources inside the fuel system, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
AD 2005-23-16 · published Nov 16, 2005, effective Dec 21, 2005
Boeing Model 737-600, -700, -700C, -800, and -900 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires modification of certain wire bundles located above the center fuel tank. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent chafed wire bundles near the center fuel tank, which could cause electrical arcing through the tank wall and ignition of fuel vapor in the fuel tank, and result in a fuel tank explosion.
AD 2005-23-17 · published Nov 16, 2005, effective Dec 21, 2005
Boeing Model 737 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737 airplanes. This AD requires, for certain airplanes, a one-time detailed inspection for interference between a clamp assembly and the wires behind the P15 refuel panel, and corrective actions if necessary. For certain other airplanes, this AD requires a one-time detailed inspection for discrepancies of the wires behind the P15 refuel panel; and corrective and related investigative actions if necessary. This AD is prompted by evidence of chafed wiring behind the P15 refuel panel and arcing to the back of the P15 refuel panel and adjacent wing structure. We are issuing this AD to detect and correct chafing of the wiring behind the P15 refuel panel, which could lead to arcing and fire with consequent airplane damage and injury to refueling personnel.
AD 2005-23-18 · published Nov 16, 2005, effective Dec 1, 2005
Fokker Model F27 Mark 050 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F27 Mark 050 airplanes. This AD requires a one-time inspection of the bleed air supply ducts to determine if blanking plugs are present and a one-time inspection of the entire area of the engine nacelle for heat damage; and corrective actions if necessary. This AD also requires replacement of the blanking plugs with clamping devices. This AD results from heat damage in areas adjacent to the bleed air supply duct assembly. We are issuing this AD to prevent rupture of the bleed air supply duct, which could lead to hot bleed air leaking into the engine controls area and result in heat damage to control cables, electrical wiring, hydraulic components, and fuel lines, and consequent fire.
AD 2005-23-19 · published Nov 21, 2005, effective Dec 27, 2005
Boeing Model 767-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200 and -300 series airplanes. This AD requires replacing hinge assemblies with new hinge assemblies in the outboard overhead stowage bins and reworking hinge assemblies in the outboard overhead stowage bins that are adjacent to curtain tracks. This AD results from reports of hinge assemblies of outboard overhead stowage bins breaking or the stowage bin doors not latching properly. We are issuing this AD to prevent the outboard overhead stowage bins opening during flight and releasing baggage, and consequently injuring passengers and blocking the aisles during emergency egress.
AD 2005-23-20 · published Nov 21, 2005, effective Dec 27, 2005
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 Airplanes, and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-135 airplanes, and Model EMB-145, -145ER, - 145MR, -145LR, -145XR, -145MP, and -145EP airplanes. This AD requires modification of the upper frame of the firewall for the auxiliary power unit (APU). This AD results from the discovery of a hole in the upper frame of the firewall for the APU. We are issuing this AD to ensure that the APU compartment is isolated from the rest of the airplane in the event of an APU fire. If the APU compartment is not isolated, smoke could enter the passenger cabin in the event of an APU fire.
AD 2005-23-21 · published Nov 21, 2005, effective Dec 6, 2005
Airbus Model A340-200 and A340-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A340-200 and A340-300 series airplanes. This AD requires repetitive inspections for cracking of the junction between the thrust reverser forward frame and the 12 o'clock and 6 o'clock beams; the thrust reverser common fittings; and the thrust reverser J-ring structure at the 12 o'clock and 6 o'clock positions; and related investigative and corrective actions. This AD results from fatigue and damage tolerance testing of the engine thrust reversers which revealed fatigue cracking of the junction between the thrust reverser forward frame and the 12 o'clock beam, and of the thrust reverser J-ring structure. We are issuing this AD to detect and correct such fatigue cracking, which could result in rupture of the J-ring, forward frame, or common fittings; loss of the thrust reverser system; or inadvertent deployment of a thrust reverser in flight and consequent reduced controllability of the airplane.
AD 2005-23-22 · published Nov 21, 2005, effective Dec 6, 2005
British Aerospace Model HS 748 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all British Aerospace Model HS 748 airplanes. This AD requires repetitive inspections for fatigue cracking, corrosion, and other related discrepancies of the rear pressure bulkhead and associated areas, and the fin attachment fittings, particularly the fin link beam; and related investigative and corrective actions. This AD results from a structural integrity audit of the airplane that showed the importance of inspecting for fatigue cracking and corrosion of these areas. We are issuing this AD to detect and correct cracking, corrosion, and other related discrepancies of the rear pressure bulkhead and associated areas, and the fin attachment fittings, particularly the fin link beam, which could result in damage to the airplane structure or injury to airplane occupants.
AD 2005-23-12 · published Nov 22, 2005, effective Dec 27, 2005
BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ airplanes. That AD currently requires revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness to incorporate life limits for certain items and inspections to detect fatigue cracking in certain structures. This new AD requires revising the ALS of the Instructions for Continued Airworthiness to incorporate new and more restrictive life limits for certain items and new and more restrictive inspections to detect fatigue cracking in certain structures. This new AD results from issuance of a later revision to the airworthiness limitations of the BAe/Avro 146 Aircraft Maintenance Manual, which specifies new inspections and compliance times for inspection and replacement actions. We are issuing this AD to ensure that fatigue cracking of certain structural elements is detected and corrected; such fatigue cracking could adversely affect the structural integrity of these airplanes.
AD 2005-24-02 · published Nov 23, 2005, effective Dec 28, 2005
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 Airplanes and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain EMBRAER Model EMB-135 airplanes and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP airplanes. That AD currently requires revising the airplane flight manual (AFM) to prohibit in-flight auxiliary power unit (APU) starts, and installing a placard on or near the APU start/stop switch panel to provide such instructions to the flightcrew. This new AD adds an optional revision to the AFM that allows limited APU starts and adds a terminating action. This AD results from the airplane manufacturer developing modifications that revise or eliminate the need for restrictions to in-flight APU starts. We are issuing this AD to prevent flame backflow into the APU compartment through the eductor during in- flight APU starts, which could result in fire in the APU compartment.
AD 2005-24-03 · published Nov 23, 2005, effective Dec 28, 2005
Boeing Model 737-600, -700, -700C, and -800 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, and -800 series airplanes. This AD requires inspecting/measuring the length of the attachment fasteners between the nacelle support fittings and the lower wing skin panels, and related investigative/corrective actions if necessary. This AD results from a report from the manufacturer that in production, during the installation of certain attachment fasteners for the nacelle support fittings, only one washer was installed instead of two. We are issuing this AD to prevent inadequate fastener clamp-up, which could result in cracking of the fastener holes, cracking along the lower wing skin panels, fuel leaking from the wing fuel tanks onto the engines, and possible fire.
AD 2005-24-04 · published Nov 23, 2005, effective Dec 28, 2005
Boeing Model 767-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-300 series airplanes. This AD requires replacing the frequency converters used to supply power for medical and galley utility outlets with modified frequency converters, and related actions. This AD results from a report indicating that a hard short circuit condition between the output of certain frequency converters and their downstream circuit breakers will produce a continuous output current that could cause the undersized output wiring to overheat when the frequency converters fail to shut off. We are issuing this AD to prevent overheating of the output wiring of the frequency converters, which could result in the failure of a wire bundle and consequent adverse effects on other systems sharing the affected wire bundle.
AD 2005-24-06 · published Nov 23, 2005, effective Nov 30, 2005
Airbus Model A318-100, A319-100, A320-200, A321-100, and A321-200 Series Airplanes, and Model A320-111 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A318-100, A319-100, A320-200, A321-100, and A321-200 series airplanes, and Model A320-111 airplanes. This AD requires an inspection to determine whether certain braking and steering control units (BSCUs) are installed or have ever been installed. For airplanes on which certain BSCUs are installed or have ever been installed, this AD requires an inspection of the nose landing gear (NLG) upper support and corrective action if necessary, and a check of the NLG strut inflation pressure and an adjustment if necessary. For some of these airplanes, this AD also requires a revision to the aircraft flight manual to incorporate an operating procedure to recover normal steering in the event of a steering failure. This AD results from a report of an incident where an airplane landed with the NLG turned 90 degrees from centerline. We are issuing this AD to prevent landings with the NLG turned 90 degrees from centerline, which could result in reduced controllability of the airplane.
AD 2005-24-07 · published Nov 29, 2005, effective Dec 29, 2005
Pacific Aerospace Corporation Ltd. Model 750XL Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Pacific Aerospace Corporation Ltd Model 750XL airplanes. This AD requires you to inspect the condition of the left and right outer panel attachment lugs for damage (scoring and gouging) and/or cracks (using a fluorescent penetrant inspection procedure for the crack inspection); to inspect the spacing of left and right outer panel attachment lugs; to replace the lugs if damage is found; and to make necessary corrections to the spacing. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for New Zealand. We are issuing this AD to prevent structural failure of the outer panel and spar due to a cracked, bent, or distorted condition of the left and right outer panel attachment lugs; and incorrect spacing of the left and right outer panel attachment lugs. This failure could lead to loss of control of the airplane.
AD 2005-24-05 · published Nov 23, 2005, effective Dec 8, 2005
Boeing Vertol Model 107-II Helicopters
This amendment adopts a new airworthiness directive (AD) for Boeing Vertol (Boeing) Model 107-II helicopters. This action requires a visual and magnetic particle inspection of the quill shaft. This amendment is prompted by the discovery of cracks in a quill shaft during a routine inspection. The actions specified in this AD are intended to detect a fatigue crack in a quill shaft and prevent separation of the quill shaft between the aft transmission and the mix box assembly, loss of rotor synchronization, and subsequent loss of control of the helicopter.
AD 2005-22-12 · published Nov 2, 2005, effective Dec 2, 2005
General Electric Company CF6-80E1 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF6-80E1 series turbofan engines installed on Airbus Industrie A330 series airplanes. This AD requires a check of the holding torque of the thrust reverser actuation system (TRAS) locks, and if necessary a visual inspection of the TRAS lock flexible drive shafts, within 10 flight cycles after all aborted takeoffs in which the thrust reverser was deployed. This AD results from reports of operators finding several damaged TRAS lock flexible drive shafts during inspections and checks of the drive shafts. We are issuing this AD to prevent inadvertent in-flight deployment of the thrust reverser, which can result in loss of control of the airplane.
AD 2005-23-09 · published Nov 9, 2005, effective Nov 25, 2005
General Electric Company (GE) CF6-80E1A1, -80E1A2, -80E1A3, -80E1A4, and -80E1A4/B Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF6-80E1A1, -80E1A2, -80E1A3, -80E1A4, and -80E1A4/B turbofan engines. This AD requires initial and repetitive fluorescent-penetrant inspections (FPI) of certain areas of high pressure compressor (HPC) cases, part number (P/N) 1509M97G07 and P/N 2083M69G03. This AD results from the discovery that HPC cases, P/N 1509M97G07 and P/N 2083M69G03, were inadvertently left out of the Airworthiness Limitations Section (ALS), Chapter 05-21-02, of GE Engine Manual, GEK 99376, Revision 17. We are issuing this AD to prevent failure of the HPC case aft mount flange, due to cracking.
AD 2005-24-08 · published Nov 30, 2005, effective Dec 15, 2005
McCauley Propeller Systems Five-Blade Propeller Assemblies
The FAA is adopting a new airworthiness directive (AD) for certain McCauley Propeller Systems propeller assemblies installed on BAE Systems (Operations) Limited Jetstream model 4100 series airplanes. This AD requires removing certain propeller hubs from service at new reduced life limits and eddy current inspections (ECIs) of the propeller hub. This AD results from three reports of cracked propeller hubs. We are issuing this AD to prevent cracked propeller hubs, which could cause failure of the propeller hub, blade separation, and loss of control of the airplane.
AD 2005-24-09 · published Nov 30, 2005, effective Dec 15, 2005
McCauley Propeller Systems Propellers
The FAA is adopting a new airworthiness directive (AD) for McCauley Propeller Systems propeller assemblies, models 2D34C53/74E-X; D2A34C58/90AT-X; 3AF32C87/82NC-X; D3AF32C87/82NC-X; D3A32C88/82NC-X; D3A32C90/82NC-X; and 3AF34C92/90LF-X. This AD requires, within 10 flight hours or 10 days after the effective date of this AD, whichever occurs first, removing certain serial number propeller hubs from service. This AD results from a report by the manufacturer that they manufactured and released 40 propeller hubs with improperly machined socket retention threads. We are issuing this AD to prevent cracked propeller hubs, which could cause failure of the propeller hub, blade separation, and loss of control of the airplane.
AD 2005-23-11 · published Nov 9, 2005, effective Dec 14, 2005
Hamilton Sundstrand Power Systems (Formerly Sundstrand Power Systems) Auxiliary Power Units Models T-62T-46C2, T-62T-46C2A, T-62T-46C3, T-62T-46C7, and T-62T-46C7A
The FAA is adopting a new airworthiness directive (AD) for Hamilton Sundstrand Power Systems (formerly Sundstrand Power Systems) auxiliary power units (APUs) models T-62T-46C2, T-62T-46C2A, T-62T- 46C3, T-62T-46C7, and T-62T-46C7A, with compressor impeller assembly, part number (P/N) 4502020 or 4502020A, installed. This AD requires removal from service of those compressor impeller assemblies at reduced service life limits. This AD results from two reports of uncontained failures of compressor impeller assemblies. We are issuing this AD to prevent an uncontained APU failure and damage to the airplane.
AD 2005-24-01 · published Nov 18, 2005, effective Jan 3, 2006
CENTRAIR 101 Series Gliders
The FAA adopts a new airworthiness directive (AD) for all CENTRAIR 101 series gliders. This AD requires you to make pen and ink changes to the Limitations Section of the glider maintenance manual to eliminate contradictory information concerning the structural life limit. This AD results from a review by FAA of the Limitations Section of the CENTRAIR Model 101AP glider maintenance manual that revealed conflicting information concerning the structural life limit. We are issuing this AD to assure that the published life limit is adhered to and to prevent structural failure of the glider once this life limit is reached.
