Airworthiness Directive · Amendment 39-22385 · Reciprocating engine power section
Continental Aerospace Technologies, Inc., Reciprocating Engines
This AD applies to Continental Aerospace Technologies, Inc. (Continental) GTSIO-520-C, -D, -H, -K, -L, -M, -N, and -S; IO-360-A, -AB, -AF, -C, -CB, -D, -DB, -E, -ES, -G, -GB, -H, -HB, -J, -JB, -K, and -KB; IO-470-A, -C, -D, -E, -F, -G, -H, -J, -K, -L, -LO, -M, -N, -P, -R, -S, -T, -U, -V, and -VO; IO-520-A, -B, -BA, -BB, -C, -CB, -D, -E, -F, -J, -K, -L, -M, and -MB; IO-550-A, -B, -C, -D, -E, -F, -G, -L, -N, -P, and -R; LTSIO-360-E, -EB, -KB, and -RB; LTSIO-520-AE; O-470-A, -B, -E, -G, -H, -J, -K, -L, -M, -N, -R, -S, -T, and -U; TSIO-360-A, -AB, -B, -BB, -C, -CB, -D, -DB, -E, -EB, -F, -FB, -G, -GB, -H, -HB, -JB, -KB, -LB, -MB, -RB, and -SB; TSIO-520-A, -AE, -AF, -B, -BB, -BE, -C, -CE, -D, -DB, -E, -EB, -G, -H, -J, -JB, -K, -KB, -L, -LB, -M, -NB, -P, -R, -T, -UB, -VB, and -WB; TSIO-550-A, -B, -C, -E, -G, -K, and -N; TSIOF-550-K; and TSIOL-550-A, -B, and -C model reciprocating engines.
The FAA is superseding Airworthiness Directive (AD) 2023-04-08 which applied to certain Continental Aerospace Technologies, Inc. (Continental) GTSIO-520-C, -D, -H, -K, -L, -M, -N, and -S; IO-360-A, - AB, -AF, -C, -CB, -D, -DB, -E, -ES, -G, -GB, -H, -HB, -J, -JB, -K, and -KB; IO-470-D, -E, -G, -H, -J, -K, -L, -M, -N, -P, -R, -S, -T, -U, -V, and -VO; IO-520-A, -B, -BA, -BB, -C, -CB, -D, -E, -F, -J, -K, -L, -M, and -MB; IO-550-A, -B, -C, -D, -E, -F, -G, -L, -N, -P, and -R; LTSIO- 360-E, -EB, -KB, and -RB; LTSIO-520-AE; O-470-A, -B, -E, -G, -H, -J, - K, -L, -M, -N, -R, -S, -T, and -U; TSIO-360-A, -AB, -B, -BB, -C, -CB, - D, -DB, -E, -EB, -G, -GB, -H, -HB, -JB, -KB, -LB, -MB, -RB, and -SB; TSIO-520-A, -AE, -AF, -B, -BB, -BE, -C, -CE, -D, -DB, -E, -EB, -G, -H, -J, -JB, -K, -KB, -L, -LB, -M, -NB, -P, -R, -T, -UB, -VB, and -WB; TSIO-550-A, -B, -C, -E, -G, -K, and -N; TSIOF-550-K; and TSIOL-550-A, - B, and -C model reciprocating engines. AD 2023-04-08 required inspection of the crankshaft assembly for proper installation of the counterweight retaining rings in the counterweight groove and, depending on the results of the inspection, corrective actions if improper installation was found. This AD continues to require inspection of the crankshaft assembly for proper installation of the counterweight retaining rings in the counterweight groove, and corrective actions if improper installation is found. Since the FAA issued AD 2023-04-08, operators notified the FAA, and Continental confirmed, that certain affected model reciprocating engines not included in the applicability of AD 2023-04-08 are also affected by the unsafe condition. Additionally, the FAA determined the special flight permit paragraph required revision. This AD was prompted by a report of a quality escape involving improper installation of counterweight retaining rings in the engine crankshaft counterweight groove during manufacture. The FAA is issuing this AD to address the unsafe condition on these products.
For affected engines with an installed crankshaft assembly identified in paragraphs (g)(1) or (2) of this AD, before further flight, do the actions identified in, and in accordance with paragraph III, Action Required, of Continental Mandatory Service Bulletin MSB23-01, Revision A, dated February 16, 2023 (MSB23-01A).
(1) Crankshaft assembly having a crankshaft serial number listed in Appendix 1 of MSB23-01A; or
(2) Crankshaft assembly that was repaired or installed on or after June 1, 2021, having a part number and crankshaft serial number listed in Appendix 2 of MSB23-01A.
Where paragraph III.1.a. of MSB23-01A specifies actions for spare crankshaft assemblies, this AD does not require those actions.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
