Airworthiness Directive · Amendment 39-21987 · Wings
Airbus SAS Airplanes
This AD applies to Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2021-0167, dated July 14, 2021 (EASA AD 2021-0167).
(1) Model A318-111, -112, -121, and -122 airplanes.
(2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes.
(3) Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes.
(4) Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes.
The FAA is superseding Airworthiness Directive (AD) 2018-09- 09, which applied to certain Airbus Model A318 and A319 series airplanes; all Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes; and all Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. AD 2018-09-09 required modifying the holes of the upper cleat to upper stringer attachments at certain areas of the left- and right-hand wings. Since the FAA issued AD 2018-09-09, additional affected configurations were identified and, for certain airplanes, it was determined that additional modification work and revised compliance times are necessary. This AD retains the requirements of AD 2018-09-09 and adds airplanes, requires different compliance times for certain airplane configurations, and, for certain airplanes, requires additional modifications or reduces compliance times, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2021-0167.
(1) Where EASA AD 2021-0167 refers to its effective date, this AD requires using the effective date of this AD.
(2) The “Remarks” section of EASA AD 2021-0167 does not apply to this AD.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
