18 Airworthiness Directives: 10 airplane, 4 rotorcraft, 3 engine, 1 various.
AD 2024-25-03 · published Jan 8, 2025, effective Feb 12, 2025
Gulfstream Aerospace Corporation Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII-G600 airplanes. This AD was prompted by a report of cracking in the electrical grounding receptacles located on the left and right wings. This AD requires inspecting the electrical grounding receptacles for cracks and corrosion, performing applicable on-condition actions, and sealing over the grounding receptacles on the top of the wings to permanently disable the receptacle. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-05 · published Jan 8, 2025, effective Feb 12, 2025
Airbus Defense and Space S.A. (Formerly Known as Construcciones Aeronauticas, S.A.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Defense and Space S.A. Model CN-235, CN-235-200, and CN-235-300 airplanes. This AD was prompted by a torn bulkhead seal found jamming the nose landing gear (NLG) emergency cable pulley. Due to the similarity of design, the main landing gear (MLG) emergency cable pulley could be exposed to the same failure mode. This AD requires repetitive inspections and corrective actions for damage of affected bulkhead seals and retainer rings, and repetitive replacement of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-08 · published Jan 8, 2025, effective Feb 12, 2025
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 767-200, -300, and -300F airplanes. This AD was prompted by a report of a main landing gear (MLG) collapse event following maintenance where a grinder was operating outside of its input parameters, resulting in possible heat damage to the outer cylinder of the MLG. This AD requires replacing affected outer cylinders. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-09 · published Jan 10, 2025, effective Feb 14, 2025
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757 airplanes. This AD was prompted by reports of several occurrences of a power transfer unit (PTU) control valve that failed to open when commanded. This AD requires installing new relays and changing certain wire bundles leading to the PTU control valve. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-01 · published Jan 14, 2025, effective Jan 29, 2025
Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2023-23- 09, which applied to all Embraer S.A. Model ERJ 190-400 airplanes. AD 2023-23-09 required repetitive inspections of the press-fitted bushings of the wing ailerons for migration and broken sealant, measurements of the distance between the aileron surfaces and hinge fittings, functional checks of the backlash of the wing aileron control system, and all applicable related investigative and corrective actions. Since the FAA issued AD 2023-23-09, it was determined that certain requirements needed to be clarified. This AD continues to require all actions of ANAC AD 2023-05-02 with revised compliance requirements, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-04 · published Jan 14, 2025, effective Jan 29, 2025
Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2023-23- 10, which applied to all Embraer S.A. Model ERJ 190-300 airplanes. AD 2023-23-10 required repetitive inspections of the press-fitted bushings of the wing ailerons for migration and broken sealant, measurements of the distance between the aileron surfaces and hinge fittings, functional checks of the backlash of the wing aileron control system, and all applicable related investigative and corrective actions. Since the FAA issued AD 2023-23-10, it was determined that certain requirements needed to be clarified. This AD continues to require all actions of ANAC AD 2023-06-01 with revised compliance requirements, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-11 · published Jan 31, 2025, effective Mar 7, 2025
Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2022-19- 02, which applied to certain Airbus SAS Model A330-200, -200 Freighter, and -300 series airplanes; and Model A330-841 and A330-941 airplanes. AD 2022-19-02 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD continues to require certain actions in AD-2022-19-02, and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-12 · published Jan 31, 2025, effective Mar 7, 2025
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, -133, - 151N, and -153N airplanes; A320 series airplanes; and A321-211, -212, - 213, -231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, - 253NX, -271NX, and -272NX airplanes. This AD was prompted by a determination that a damage-tolerance and fatigue reassessment of nose landing gear (NLG) repairs is necessary for certain parts fitted on airplanes approved for operation in the Commonwealth of Independent States (CIS). This AD requires repair and replacement of all affected parts, and introduces restrictions for the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-26-03 · published Jan 31, 2025, effective Mar 7, 2025
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767-200, -300, and -400ER series airplanes. This AD was prompted by a report of multiple engine indicating and crew alerting system messages during potable water servicing after the water leaked onto the electronics equipment cooling air filter. This AD requires installation of hoseducts around the left-side section 43 potable water supply hoses and connections, a potable water system leakage test, and applicable corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-26-04 · published Jan 31, 2025, effective Feb 18, 2025
Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2023-09- 01, which applied to all Airbus SAS Model A318 series airplanes; Model A319 series airplanes; Model A320-211, -212, -214, -216, -231, -232, - 233, -251N, -252N, -253N, -271N, -272N, and -273N airplanes; and Model A321 series airplanes. AD 2023-09-01 was prompted by a report that certain overheat detection system (OHDS) sensing elements installed at certain positions might not properly detect thermal bleed leak events due to a quality escape during the manufacturing process. AD 2023-09-01 required a one-time detailed inspection of each affected part installed at an affected position and replacement if necessary and prohibited the installation of affected parts at affected positions. Since the FAA issued AD 2023-09-01, a new airplane model (A321-253NY) has been certified by EASA, on which affected parts could be installed in service. This AD continues to require the actions in AD 2023-09-01, and revises the applicability to include Model A321-253NY airplanes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-51 · published Jan 2, 2025, effective Jan 17, 2025
Airbus Helicopters Deutschland GmbH Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH Model MBB-BK 117 C-2 helicopters. The FAA previously sent this AD as an emergency AD to all known U.S. owners and operators of these helicopters. This AD was prompted by a report of vibrations of the yaw axis during a hover taxi. This AD requires repetitively inspecting the bolted joint between the cardan- pivot joint assembly and the tail rotor actuator piston rod and, depending on the results, taking corrective action. This AD also prohibits installing certain tail rotor actuators unless its requirements are met. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-26-01 · published Jan 2, 2025, effective Jan 17, 2025
Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model H160-B helicopters. This AD was prompted by a report of excessive axial play of the rotating scissors spherical bearings. This AD requires measuring the axial play of the rotating scissors spherical bearings and, depending on the results, accomplishing corrective action and reporting inspection results, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-26-08 · published Jan 2, 2025, effective Jan 17, 2025
Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB139 and AW139 helicopters. This AD was prompted by reports of broken main landing gear (MLG) shock absorber piston rod eye ends. This AD requires repetitively inspecting the MLG shock absorber piston rod eye ends, reporting the results of the inspection, and, depending on the results, replacing the MLG shock absorber assembly. It also prohibits installing certain MLG shock absorber assemblies unless specific requirements are met, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2025-03-02 · published Jan 31, 2025, effective Mar 7, 2025
Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) certain Airbus Helicopters Model AS332C, AS332C1, AS332L, AS332L1, AS332L2, AS355E, AS355F, AS355F1, AS355F2, AS355N, AS355NP, AS-365N2, AS 365 N3, EC 155B, EC155B1, EC225LP, SA-365N, and SA-365N1 helicopters. This AD was prompted by a report of an unintentional activation of the hoist shear-button (shear-button) on the collective pitch handle during a night flight. This AD requires checking the operation of the shear- button safety-cap on each applicable collective pitch handle and prohibits installing certain part-numbered collective pitch handles or collective sticks with those part-numbered collective pitch handles installed unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-02 · published Jan 8, 2025, effective Feb 12, 2025
CFM International, S.A. Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1B engines. This AD was prompted by a report of a quality escape involving certain high- pressure compressor (HPC) stage 2 seals manufactured without detailed finish machining, which could result in deeper rubs and mechanical damage to the seal teeth of the stage 3-4 compressor rotor blisk (stage 3-4 blisk) of the mating compressor rotor during initial operation. This AD requires a visual inspection of the HPC stage 2 seal, a visual inspection of the forward arm seal teeth of the stage 3-4 blisk, an eddy current inspection (ECI) of the forward arm seal teeth of the stage 3-4 blisk, and replacement of the HPC stage 2 seal and the stage 3-4 blisk, if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-07 · published Jan 8, 2025, effective Feb 12, 2025
General Electric Company Engines
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx- 1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx-1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/P2, GEnx- 1B76A/P2, GEnx-2B67, GEnx-2B67B, and GEnx-2B67/P engines. This AD was prompted by a manufacturer evaluation that determined a lower life limit may be necessary for certain stages 6-10 compressor rotor spools than allowed by the engine shop manual (ESM). This AD requires a one- time inspection of the stages 6-10 spools for previously accomplished blend repairs, a one-time inspection of the blend repairs on the stages 6-10 spools for compliance with the updated allowable limits, and replacement if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-25-10 · published Jan 31, 2025, effective Feb 18, 2025
Rolls-Royce Deutschland Ltd & Co KG Engines
The FAA is adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent XWB-97 engines. This AD was prompted by a report of damage to the main fuel hose assembly of the fuel manifold, which resulted an in-flight shut down. This AD requires a one-time set of visual and dimensional inspections of the main fuel hose assembly of the fuel manifold to confirm softness, compliance, and lack of resistance, and for shrinkage, cracks, chafing, dents, kinks, necking, and degradation of the hose braid wire; and, if necessary, replacement of the main fuel hose assembly of the fuel manifold, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2024-26-02 · published Jan 31, 2025, effective Mar 7, 2025
Various Airplanes and Helicopters
The FAA is superseding Airworthiness Directive (AD) 2021-07-13 for certain Pacific Scientific Company rotary buckle assemblies (buckles). AD 2021-07-13 required inspecting each specified buckle including its buckle handle vane and prohibited installing affected buckles. This AD was prompted by the publication of an updated service bulletin, which revises the applicability based on date of manufacture of the affected buckles. This AD retains certain requirements of AD 2021-07-13, reduces the applicability, and requires performing corrective actions by complying with certain portions of the updated service bulletin. The FAA is issuing this AD to address the unsafe condition on these products.
