26 Airworthiness Directives: 12 airplane, 7 rotorcraft, 3 engine, 2 appliance, 1 glider, 1 various.
AD 2022-03-21 · published Mar 7, 2022, effective Apr 11, 2022
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by significant changes, including new or more restrictive requirements, made to the airworthiness limitations (AWLs) related to fuel tank ignition prevention and the nitrogen generation system. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-04-08 · published Mar 7, 2022, effective Apr 11, 2022
Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-16- 01, which applied to all Airbus SAS Model A318, A319, A320, and A321 series airplanes. AD 2020-16-01 required repetitive cleaning and greasing of affected cargo door seals (both original equipment manufacturer (OEM) and parts manufacturer approval (PMA) parts). This AD was prompted by reports of low halon concentration in the forward and aft cargo compartments due to air leakage through cargo compartment door seals, and the FAA's determination that improved cargo door seals must be installed and that certain flight operations must be limited until the improved cargo door seals are installed. This AD retains certain actions required by AD 2020-16-01 and requires replacing certain forward and aft cargo compartment door seals with new seals and installing a placard on the cargo compartment doors; and for certain airplanes, revising the existing airplane flight manual (AFM) to implement an operational limitation for certain routes. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-05-07 · published Mar 7, 2022, effective Apr 11, 2022
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a report that in the event of a specific discrete wire failure, the landing gear extension and retraction system (LGERS) may not be able to complete landing gear retraction when commanded by moving the landing gear lever to the UP position. This AD requires revising the operator's existing FAA-approved minimum equipment list (MEL) for the LGERS, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-05-11 · published Mar 9, 2022, effective Apr 13, 2022
Viking Air Limited (Type Certificate Previously Held by Bombardier Inc.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for Viking Air Limited (type certificate previously held by Bombardier Inc.) Model DHC-3 airplanes with a certain wing strut assembly installed. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as fatigue damage of the wing struts. This AD requires a bolt hole eddy current inspection of the lug plate holes, a visual and fluorescent dye penetrant inspection of the lug fittings, and a visual and eddy current surface scan inspection of the wing strut assemblies. This unsafe condition could lead to failure of the wing strut, which could result in an in- flight breakup of the wing. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-05-12 · published Mar 9, 2022, effective Apr 13, 2022
Embraer S.A. (Type Certificate Previously Held by Empresa Brasileira de Aeronáutica S.A.) Airplanes
The FAA is superseding Airworthiness Directive (AD) 2020-12-08 for all Embraer S.A. Model EMB-505 airplanes. AD 2020-12-08 required inspections of the mass-balance weights of the elevators, ailerons, and rudder (flight control surfaces) and their attachment parts, and corrective actions if necessary, and revising the airworthiness limitation section (ALS) of the maintenance manual or instructions for continued airworthiness to incorporate new airworthiness limitations. This AD retains the actions required by AD 2020-12-08 and requires, for certain airplanes, cleaning and weighing certain mass-balances and installation or replacement, as applicable; and for certain other mass- balances for certain airplanes, replacement of those mass-balances. This AD was prompted by a determination that new applicable airplane serial numbers and new criteria for the replacement of affected parts are necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-05-14 · published Mar 9, 2022, effective Mar 24, 2022
GROB Aircraft SE (Type Certificate Previously Held by GROB Aircraft AG) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all GROB Aircraft SE (type certificate previously held by GROB Aircraft AG) (GROB) Model G 115EG airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as in-flight detachment of a rudder actuator hinge bracket. This AD requires repairing the support structure at the attachment to the attachment bolts on certain flight control surfaces, inspecting the support structure at the attachment bolts of all flight control surfaces, and taking corrective actions if discrepancies are detected. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-10 · published Mar 11, 2022, effective Apr 15, 2022
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes. This AD was prompted by reports of three incidents involving in-flight fan blade failures on certain Pratt & Whitney engines ("fan blades" are also known as "1st-stage low-pressure compressor (LPC) blades"-- these terms are used interchangeably in this AD). This AD requires installation of debris shields on the thrust reverser (T/R) inner wall at the left and right sides of the lower bifurcation, inspection of the fan cowl doors for moisture ingression, repetitive functional checks of the hydraulic pump shutoff valves to ensure they close in response to the fire handle input, and corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-11 · published Mar 11, 2022, effective Apr 15, 2022
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes. This AD was prompted by reports of three incidents involving in-flight fan blade failures on certain Pratt & Whitney engines ("fan blades" are also known as "1st-stage low- pressure compressor (LPC) blades"--these terms are used interchangeably in this AD). This AD requires modifying the engine inlet to withstand fan blade failure event loads. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-05-13 · published Mar 14, 2022, effective Apr 18, 2022
Honda Aircraft Company LLC Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Honda Aircraft Company LLC (Honda) Model HA-420 airplanes. This AD was prompted by a report of in-flight smoke and fire that initiated from the windshield heat power wire braid. This AD requires incorporating temporary revisions into the airplane flight manual (AFM) and the quick reference handbook (QRH) that modify procedures for windshield heat operation until the affected windshield assemblies are replaced. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-16 · published Mar 16, 2022, effective Mar 16, 2022
The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, and 747-400F series airplanes. This AD was prompted by a determination that radio altimeters cannot be relied upon to perform their intended function if they experience interference from wireless broadband operations in the 3.7-3.98 GHz frequency band (5G C-Band), and a recent determination that during takeoff, approach, landings, and go-arounds, as a result of this interference, certain airplane systems may not properly function, resulting in increased flightcrew workload while on approach with the flight director, autothrottle, or autopilot engaged, which could result in reduced ability of the flightcrew to maintain safe flight and landing of the airplane. This AD requires revising the limitations and operating procedures sections of the existing airplane flight manual (AFM) to incorporate specific operating procedures for takeoff, instrument landing system (ILS) approaches, non-precision approaches, and go-around and missed approaches, when in the presence of 5G C-Band interference as identified by Notices to Air Missions (NOTAMs). The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-02 · published Mar 22, 2022, effective Apr 26, 2022
Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2013-25- 11, which applied to all Airbus SAS Model A318-111, -112, -121, and - 122 airplanes; Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320-111, -211, -212, -214, -231, -232, and -233 airplanes; and Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. AD 2013-25-11 required repetitive inspections of the 80VU rack lower lateral fittings, upper fittings, and shelves for damage, repetitive inspections of the 80VU rack lower central support for cracking, and corrective action if necessary. AD 2013-25-11 also specified optional terminating action for the repetitive inspections. Since the FAA issued AD 2013-25-11, new damage occurrences have been reported, and a different compliance time has been determined for certain inspections, depending on airplane configuration. This AD expands the applicability, removes the optional terminating action, and requires new repetitive inspections; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-26-20 · published Mar 29, 2022, effective May 3, 2022
Airbus SAS Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-03 · published Mar 14, 2022, effective Mar 16, 2022
Bell Textron Inc. (Type Certificate Previously Held by Bell Helicopter Textron Inc.) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2022-02-02 which applied to certain Bell Textron Inc. (type certificate previously held by Bell Helicopter Textron Inc.) Model 204B, 205A, 205A-1, 205B, 210, and 212 helicopters with a certain main rotor hub strap pin (pin) installed. AD 2022-02-02 required removing certain outboard pins from service and prohibited installing them on any helicopter. This AD expands the applicability to all affected pins, regardless if they are outboard or inboard. This AD also requires inspecting the removed pin for any deformation and if it is deformed, removing the mating strap fitting (fitting) from service. This AD was prompted by the discovery that AD 2022-02-02 inadvertently limited its applicability to only outboard pins when, in fact, all pins are subject to the unsafe condition and the determination that a deformed pin may have damaged the fitting. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-13 · published Mar 15, 2022, effective Mar 30, 2022
Airbus Helicopters Deutschland GmbH (AHD) Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Deutschland GmbH (AHD) Model MBB-BK 117 C-2 and MBB-BK 117 D-2 helicopters. This AD was prompted by a report of erroneous or partial installation of the seat belt restraint system. This AD requires inspecting certain seats, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-01 · published Mar 16, 2022, effective Apr 20, 2022
Airbus Helicopters Deutschland GmbH Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH Model MBB-BK 117 D-3 helicopters. This AD was prompted by reports of a main rotor (M/R) blade lead-lag damper in a tilted position. This AD requires inspecting the Flex Control Unit (FCU), and corrective actions if necessary, as well as rework and re-identification of the bearing pin, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-20 · published Mar 22, 2022, effective Apr 26, 2022
Bell Textron Canada Limited (Type Certificate Previously Held by Bell Helicopter Textron Canada Limited) Helicopters
The FAA is superseding Airworthiness Directive (AD) 2020-20- 06, which applied to certain Bell Helicopter Textron Canada Limited (now Bell Textron Canada Limited) Model 429 helicopters. AD 2020-20-06 required repetitive inspections of certain cyclic and collective assembly bearings. This AD was prompted by new bellcrank assemblies, which have been upgraded with corrosion resistant steel bearings. This AD retains certain requirements of AD 2020-20-06, and depending on the inspection results, requires removing certain parts from service and installing the upgraded cyclic and collective bellcrank assemblies. This AD also requires installing the upgraded collective and cyclic bellcrank assemblies on certain helicopters if not already installed, and prohibits installing certain bellcrank assemblies. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-07-03 · published Mar 23, 2022, effective Apr 27, 2022
Bell Textron Inc., Helicopters
The FAA is adopting a new airworthiness directive (AD) for Bell Textron Inc., Model 412, 412EP, and 412CF helicopters. This AD was prompted by evaluation results showing flight loads that impact the collective lever fatigue life. This AD requires adding a permanent hours time-in-service (TIS) penalty for certain collective levers and prohibits installing those collective levers unless the permanent hours TIS penalty has been added. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2021-03-16 R1 · published Mar 24, 2022, effective Mar 24, 2022
Airbus Helicopters Helicopters
The FAA is removing Airworthiness Directive (AD) 2021-03-16, which applied to all Airbus Helicopters Model AS350B, AS350B1, AS350B2, AS350B3, AS350BA, AS350D, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters. AD 2021-03-16 required inspecting each sliding door and replacing the upper rail or front roller or removing the front roller from service if necessary. Since the FAA issued AD 2021-03-16, inspection results and further investigation have confirmed that the in-flight loss of a sliding door, which prompted AD 2021-03-16, was an isolated case resulting from incorrect operation and maintenance error. Therefore, the FAA has determined that no unsafe condition is likely to exist or develop on the sliding doors on other helicopters in the fleet. Accordingly, AD 2021-03-16 is removed.
AD 2022-07-11 · published Mar 31, 2022, effective May 5, 2022
Leonardo S.p.a. Helicopters
The FAA is superseding Airworthiness Directive (AD) 2021-17- 18, which applied to all Leonardo S.p.a. Model A109C, A109K2, A109E, A109S, and AW109SP helicopters. AD 2021-17-18 required an inspection of certain tail rotor (TR) sleeve assemblies for discrepancies, an inspection of certain TR shaft assemblies for discrepancies, a repetitive measurement of the position of the bushing of the TR sleeve assembly in relation to the pitch change slider assembly, and corrective actions if necessary. This AD retains the requirements of AD 2021-17-18, and also requires repetitive inspections of the TR sleeve assemblies, and corrective actions if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by a determination that additional actions are required to address the unsafe condition. This AD was also prompted by a report of a crack on the TR mast. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-02-03 · published Mar 1, 2022, effective Mar 22, 2022
CFM International, S.A. Turbofan Engines
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. The AD applies to CFM International, S.A. CFM56-3 and CFM56-7B model turbofan engines with certain accessory gearbox assembly (AGB) not equipped with a dynamic oil seal assembly in the handcranking pad. As published, the part numbers (P/Ns) listed in paragraph (i)(2)(i) are incorrect. This document corrects that error. In all other respects, the original document remains the same; however, for clarity, the FAA is publishing the entire rule in the Federal Register.
AD 2022-05-08 · published Mar 7, 2022, effective Apr 11, 2022
General Electric Company Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) CF34-10E model turbofan engines. This AD was prompted by a manufacturer investigation that revealed Teflon material in the A-sump oil strainer (strainer assembly) screen after several reports of in-flight shutdowns (IFSDs) and unscheduled engine removals (UERs). This AD requires initial and repetitive visual inspections of the strainer assembly screen. As a terminating action to the initial and repetitive visual inspections, this AD requires the replacement of the stationary oil seal at the No. 1 forward bearing. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-09 · published Mar 11, 2022, effective Apr 15, 2022
Pratt & Whitney Division Turbofan Engines
The FAA is superseding Airworthiness Directive (AD) 2019-03-01 and AD 2021-05-51 for certain Pratt & Whitney Division (PW) PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 model turbofan engines. AD 2019-03-01 required performing initial and repetitive thermal acoustic image (TAI) inspections for cracks in certain 1st- stage low-pressure compressor (LPC) blades and removal of those blades that fail inspection. AD 2021-05-51 required performing a one-time TAI inspection for cracks in certain 1st-stage LPC blades and removal of those blades that fail inspection. This AD was prompted by three in- flight failures of a 1st-stage LPC blade, with one failure resulting in an engine fire during flight, and subsequent manufacturer publication of service information specifying improved inspections for three critical locations on the 1st-stage LPC blade. This AD requires initial and repetitive ultrasonic (UT) inspections and TAI inspections for cracks in certain 1st-stage LPC blades and removal of those blades that fail inspection. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-05-10 · published Mar 16, 2022, effective Apr 20, 2022
Goodrich Externally-Mounted Hoist Assemblies
The FAA is adopting a new airworthiness directive (AD) for various model helicopters with certain part-numbered Goodrich externally-mounted hoist assemblies (hoists) installed. This AD was prompted by hoists failing lower load limit inspections. This AD requires replacing unmodified hoists, installing placards, revising the existing Rotorcraft Flight Manual (RFM) for your helicopter, deactivating or removing a hoist if a partial peel out occurs, reviewing the helicopter's hoist slip load test records, repetitively inspecting the hoist cable and overload clutch (clutch), and reporting information to the manufacturer. This AD also requires establishing operating limitations on the hoist and prohibits installing an unmodified hoist. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-07-05 · published Mar 21, 2022, effective Apr 5, 2022
MARS A.S. Parachutes
The FAA is superseding Airworthiness Directive (AD) 2022-05- 09, which applied to certain MARS A.S. emergency parachutes. AD 2022- 05-09 required removing emergency parachutes with certain manufacture dates or serial numbers from service. Since the FAA issued AD 2022-05- 09, the European Union Aviation Safety Agency (EASA) superseded its mandatory continuing airworthiness information (MCAI) to correct an unsafe condition on this aviation product. The MCAI identifies the unsafe condition as the length of the ripcord between the pins being too long, which could cause a malfunction of the emergency parachute. This AD retains the actions required by AD 2022-05-09 and expands the applicability.
AD 2022-05-05 · published Mar 7, 2022, effective Apr 11, 2022
Schempp-Hirth Flugzeugbau GmbH Gliders
The FAA is adopting a new airworthiness directive (AD) for all Schempp-Hirth Flugzeugbau GmbH Model Ventus-2a and Ventus-2b gliders. This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as severe corrosion on the inboard flaperon actuation push rods and ball bearing connecting the flaperon push rod to the bell crank inside the wing. This AD requires inspecting the affected parts of the flaperon control in the wings and taking corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
AD 2022-06-05 · published Mar 14, 2022, effective Mar 16, 2022
Various Restricted Category Helicopters
The FAA is superseding Airworthiness Directive (AD) 2021-15-52 which applied to various restricted category helicopters originally manufactured by Bell Textron Inc. with a certain main rotor hub strap pin (pin) installed. AD 2021-15-52 required removing certain outboard pins from service and prohibited installing them on any helicopter. This AD expands the applicability to all affected pins, regardless if they are outboard or inboard. This AD also requires inspecting the removed pin for any deformation and if it is deformed, removing the mating strap fitting (fitting) from service. This AD was prompted by the discovery that AD 2021-15-52 inadvertently limited its applicability to only outboard pins when, in fact, all pins are subject to the unsafe condition and the determination that a deformed pin may have damaged the fitting. Finally, this AD updates the current type certificate holder information as reflected in the type certificate data sheet (TCDS) and expands the applicability of AD 2021-15-52. The FAA is issuing this AD to address the unsafe condition on these products.
