19 Airworthiness Directives: 14 airplane, 1 rotorcraft, 4 engine.
AD 2018-11-10 · published Jun 4, 2018, effective Jul 9, 2018
Dassault Aviation Airplanes
We are superseding Airworthiness Directive (AD) 2017-01-07, which applied to all Dassault Aviation Model FAN JET FALCON airplanes; Model FAN JET FALCON SERIES C, D, E, F, and G airplanes; Model MYSTERE- FALCON 200 airplanes; Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20- F5 airplanes; and Model MYSTERE-FALCON 50 airplanes. AD 2017-01-07 required a functional test or check of the main entry door closure and warning system, and applicable door closing inspections, adjustments, operational tests, and corrective actions if necessary. This AD requires repetitive door closing inspections, adjustments, operational tests, and corrective actions if necessary. This AD was prompted by a report indicating that during approach for landing, the main entry door detached from an airplane. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-08 · published Jun 5, 2018, effective Jul 10, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767-200 and -300 series airplanes. This AD was prompted by a report of two cracks at a certain frame inner chord. This AD requires a detailed inspection for any material review board (MRB) filler installed in the area from the frame web to the stub-beam fitting at certain stations to determine if the filler extends above the frame-to-stub-beam joint, and applicable on-condition actions. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-09 · published Jun 5, 2018, effective Jul 10, 2018
Bombardier, Inc., Airplanes
We are superseding Airworthiness Directive (AD) 2014-02-01, which applied to certain Bombardier, Inc., Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), Model CL-600-2D15 (Regional Jet Series 705), and Model CL-600-2D24 (Regional Jet Series 900) airplanes. AD 2014-02-01 required repetitive inspections of the rudder travel limiter (RTL) return springs and primary actuator, and corrective actions if necessary; and replacement of certain RTL return springs. This AD requires an inspection of the RTL return springs for signs of chafing; an inspection of the casing of the primary actuator for signs of chafing or missing paint; replacement of the RTL return springs; and an inspection of the lugs of the RTL limiter arm assembly for cracks, and modification or replacement, as applicable; and applicable corrective actions. This AD also adds airplanes to the applicability. This AD was prompted by reports that when installing the RTL return springs, the RTL limiter arm assembly lug(s) can become deformed. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-11 · published Jun 5, 2018, effective Jun 20, 2018
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A350-941 airplanes. This AD requires a detailed inspection of the four retaining pins in the main landing gear support structure (MLGSS) trunnion block, left- and right-hand sides, and related investigative and corrective actions if necessary. This AD was prompted by a determination that short retaining pins may have been installed at the incorrect location of the MLGSS forward pintle. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-13 · published Jun 5, 2018, effective Jul 10, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This AD was prompted by a report of possible degraded bond-line performance of co-bonded upper wing stringer-to-skin joints. This AD requires repetitive inspections of certain upper wing stringers for any disbond and corrective actions, if necessary; and a terminating preventive modification of installing disbond arrestment (DBA) fasteners. This AD also requires revising the inspection or maintenance program to incorporate an airworthiness limitation. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-14 · published Jun 5, 2018, effective Jul 10, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767-300 and -300F series airplanes. This AD was prompted by reports of fatigue cracking on airplanes with Aviation Partners Boeing winglets installed. This AD requires high frequency eddy current (HFEC) inspections for cracking of the lower outboard wing skin, and repair or modification if necessary. This AD also requires one of three follow-on actions: Repeating the HFEC inspections, modifying certain internal stringers and oversizing and plugging the existing fastener holes of the lower wing, or modifying the external doubler/tripler and doing repetitive post-modification inspections. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-04 · published Jun 7, 2018, effective Jun 27, 2018
Aircraft Industries a.s. Airplanes
We are adopting a new airworthiness directive (AD) for Aircraft Industries a.s. Models L 410 UVP-E20 and L 410 UVP-E20 CARGO airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as un-commanded negative thrust mode activated on an engine. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2018-11-12 · published Jun 7, 2018, effective Jul 12, 2018
Bombardier, Inc., Airplanes
We are adopting a new airworthiness directive (AD) for all Bombardier, Inc., Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL- 600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by a report that Belleville washers installed on the shimmy damper of the main landing gear (MLG) may fail due to fatigue. This AD requires revising the maintenance or inspection program, as applicable, to incorporate a repetitive task specified in the maintenance review board (MRB) report. We are issuing this AD to address the unsafe condition on these products.
AD 2018-12-02 · published Jun 8, 2018, effective Jul 13, 2018
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes; Model A319-111, -112, -113, - 114, and -115 airplanes; Model A320-211, -212, -214, and -216 airplanes; and Model A321-111, -112, -211, -212, and -213 airplanes. This AD was prompted by a review of maintenance instructions for a blend repair of the snout diameter of the main beam assembly of the forward engine mount that would create an excessive gap between the bearing mono-ball and the snout. This AD requires modifying the main beam assembly of the forward engine mount. We are issuing this AD to address the unsafe condition on these products.
AD 2018-12-04 · published Jun 8, 2018, effective Jun 25, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-300ER series airplanes. This AD requires replacing the water filter assembly in certain steam ovens. This AD was prompted by a report that water can enter the steam oven cavity and become heated and then released when the oven door is opened. We are issuing this AD to address the unsafe condition on these products.
AD 2018-12-05 · published Jun 8, 2018, effective Jul 13, 2018
the Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by reports of cracks found in the rear spar web and lower chord on the left and right wings. This AD requires repetitive detailed inspections for cracking of the rear spar web and lower chord, and applicable on-condition actions. We are issuing this AD to address the unsafe condition on these products.
AD 2018-09-04 · published Jun 11, 2018, effective Jun 11, 2018
Gulfstream Aerospace Corporation Airplanes
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. The AD applies to certain Gulfstream Aerospace Corporation Models G-IV and GIV-X airplanes. Paragraphs (h)(3) through (5) of the AD incorrectly reference Customer Bulletin 238A as Customer Bulletin 283A. This document corrects that error. In all other respects, the original document remains the same; however for the sake of clarity, we are publishing the entire rule in the Federal Register.
AD 2018-12-06 · published Jun 11, 2018, effective Jul 16, 2018
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 and 787-9 airplanes. This AD was prompted by a report of an in-service reliability issue of a latent flow sensor failure combined with single cabin air compressor (CAC) operation. This condition resulted in reduced airflow which led to a persistent single CAC surge condition that caused overheat damage to the CAC inlet. This AD requires installing new pack control unit (PCU) software for the cabin air conditioning and temperature control system (CACTCS) and new CAC outlet pressure sensor J-tube hardware, and doing related investigative and corrective actions if necessary. We are issuing this AD to address the unsafe condition on these products.
AD 2018-12-07 · published Jun 18, 2018, effective Jul 23, 2018
Gulfstream Aerospace Corporation Airplanes
We are superseding Airworthiness Directive (AD) 2015-24-06 for certain Gulfstream Aerospace Corporation Model GVI airplanes. AD 2015- 24-06 required repetitive breakaway torque checks and torqueing of the main landing gear (MLG) brake inlet self-sealing couplings and inserting a dispatch and takeoff limitation to the limitations section of the airplane flight manual. This AD requires modifying the MLG and brake assembly. This AD was prompted by reports of the self-sealing couplings on the MLG brake inlet fitting backing out of the fully seated position. We are issuing this AD to address the unsafe condition on these products.
AD 2018-11-03 · published Jun 1, 2018, effective Jun 18, 2018
Airbus Helicopters
We are adopting a new airworthiness directive (AD) Airbus Helicopters Model SA-365C, SA-365C1, and SA-365C2 helicopters. This AD requires establishing a life limit of 2,000 hours time-in-service (TIS) for the Starflex star/mast connecting bolt (bolt) and removing from service each bolt that exceeds its life limit. This AD is prompted by the discovery that the bolt's life limit was not included in helicopter maintenance records. The actions of this AD are intended to prevent an unsafe condition on these products.
AD 2018-11-16 · published Jun 15, 2018, effective Jul 2, 2018
Engine Alliance Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Engine Alliance (EA) GP7270, GP7272, and GP7277 turbofan engines. This AD requires a one-time eddy current inspection (ECI) of the engine fan hub blade slot bottom and blade slot front edge for cracks, a visual inspection of the engine fan hub for damage, and removal of parts if damage or defects are found that are outside serviceable limits. This AD was prompted by an uncontained failure of the engine fan hub. We are issuing this AD to address the unsafe condition on these products.
AD 2018-13-02 · published Jun 15, 2018, effective Jul 20, 2018
Pratt & Whitney Division Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Pratt & Whitney Division (PW) PW4052, PW4056, PW4060, PW4062, PW4062A, PW4152, PW4156A, PW4158, PW4460, and PW4462 turbofan engine models, including engines identified with suffixes -1C, -1E, -3, -3A, or -3B. This AD was prompted by the discovery of multiple cracked 4th stage low-pressure turbine (LPT) air seals in the fleet. This AD requires removal from service of certain 4th stage LPT air seals. We are issuing this AD to address the unsafe condition on these products.
AD 2018-13-05 · published Jun 21, 2018, effective Jul 26, 2018
Honeywell International Inc. Turboprop and Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Honeywell International Inc. (Honeywell) TPE331 turboprop and TSE331 turboshaft engines. This AD was prompted by recent reports of failures of the direct drive fuel control gears and bearings in the hydraulic torque sensor gear assembly, part number (P/N) 3101726-3. This AD requires initial and repetitive engine oil filter sampling and analysis of the affected engines and inspections of certain hydraulic torque sensor gear assemblies. We are issuing this AD to address the unsafe condition on these products.
AD 2018-13-03 · published Jun 26, 2018, effective Jul 11, 2018
International Aero Engines Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain International Aero Engines (IAE) PW1133G-JM, PW1133GA-JM, PW1130G-JM, PW1127G-JM, PW1127GA-JM, PW1127G1-JM, PW1124G-JM, PW1124G1-JM, and PW1122G-JM turbofan engines. This AD requires a one-time visual inspection of the engine fan hub for damage, and removal of parts if damage or defects are found that are outside the serviceable limits. This AD was prompted by reports of damage to the engine fan hub. We are issuing this AD to address the unsafe condition on these products.
