29 Airworthiness Directives: 21 airplane, 3 rotorcraft, 4 engine, 1 appliance.
AD 2015-15-12 · published Aug 3, 2015, effective Sep 8, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A318, A319, and A320 series airplanes modified by a particular supplemental type certificate (STC). This AD was prompted by reports of cracks found during inspections of the in-flight entertainment system radome assembly. This AD requires repetitive detailed inspections for cracks in the radome assembly, and replacement of the radome if necessary. We are issuing this AD to detect and correct cracks in the radome assembly, which could result in the radome (or pieces) separating from the airplane and striking the tail, consequently reducing the controllability of the airplane.
AD 2015-15-13 · published Aug 3, 2015, effective Sep 8, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A319 series airplanes; Model A320-211, -212, -214, -231, - 232, and -233 airplanes; and Model A321 series airplanes. This AD was prompted by reports of cracks that could be initiated at the waste water service panel area and the potable water service panel area. This AD requires modification of the potable water service panel and waste water service panel, including doing applicable related investigative and corrective actions. We are issuing this AD to prevent any cracking at the waste water service panel area and the potable water service panel area, which could affect the structural integrity of the airplane.
AD 2015-15-15 · published Aug 3, 2015, effective Sep 8, 2015
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, 777-200LR, 777-300ER, and 777F series airplanes. This AD was prompted by a report indicating that sealant might not have been applied in production to the wing skin panel gaps above certain underwing fittings. This AD would require an inspection for missing sealant, and applicable other specified, related investigative, and corrective actions. We are proposing this AD to detect and correct missing sealant from the wing skin panel gaps above the underwing fittings, which could result in corrosion and fatigue cracking in the wing skin panel, and consequent loss of limit load capability of the wing skin and potential subsequent structural failure of the wings.
AD 2015-15-14 · published Aug 4, 2015, effective Aug 19, 2015
BAE Systems (Operations) Limited Airplanes
We are adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model ATP airplanes. This AD requires a one-time inspection for solder deposited on the frangible plug of certain engine and auxiliary power unit (APU) fire extinguishers. This AD was prompted by reports of a fire extinguisher that failed to discharge due to solder deposited on the frangible plug of the fire extinguisher. We are issuing this AD to detect and correct solder deposited on the frangible plug of the fire extinguisher, which could result in failure of the fire extinguisher to discharge, and consequent inability to put out a fire in an engine or in the APU.
AD 2015-16-01 · published Aug 11, 2015, effective Sep 15, 2015
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2012-19-11 for certain The Boeing Company Model 737 airplanes. AD 2012-19-11 required incorporating design changes to improve the reliability of the cabin altitude warning system by installing a redundant cabin altitude pressure switch, replacing the aural warning module (AWM) with a new or reworked AWM, and changing certain wire bundles or connecting certain previously capped and stowed wires as necessary. For certain airplanes, AD 2012-19-11 also required prior or concurrent incorporation of related design changes by modifying the instrument panels, installing light assemblies, modifying the wire bundles, and installing a new circuit breaker, as necessary. This AD was prompted by the report of a flightcrew not receiving an aural warning during a lack-of-cabin pressurization event. We are issuing this AD to prevent the loss of cabin altitude warning, which could delay flightcrew recognition of a lack of cabin pressurization, and could result in incapacitation of the flightcrew due to hypoxia (a lack of oxygen in the body), and consequent loss of control of the airplane.
AD 2015-16-02 · published Aug 11, 2015, effective Sep 15, 2015
Airbus Airplanes
We are superseding Airworthiness Directives (AD) 2003-14-11, AD 2004-11-08, AD 2004-13-25, AD 2004-18-14, AD 2007-05-12, AD 2008-06- 07, AD 2009-18-20, AD 2010-15-02, and AD 2012-04-07 that apply to certain Airbus Model A330 and A340 series airplanes. AD 2003-14-11, AD 2004-11-08, AD 2004-13-25, AD 2004-18-14, AD 2007-05-12, AD 2008-06-07, AD 2009-18-20, AD 2010-15-02, and AD 2012-04-07 required revising the maintenance program to incorporate certain maintenance requirements and airworthiness limitations; replacing certain flap rotary actuators; repetitively inspecting elevator servo-controllers and pressure relief valves of the spoiler servo controls; repetitively testing the elevator servo control loops, modifying the elevator servo controls, and repetitively replacing certain retraction brackets of the main landing gear; and revising the airplane flight manual. This new AD requires revising the maintenance program or inspection program to incorporate certain maintenance requirements and airworthiness limitations. This new AD also removes Airbus Model A340-200, -300, -500, and -600 series airplanes from the applicability and adds Airbus Model A330-323 airplanes to the applicability. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. We are issuing this AD to address the aging effects of aircraft systems. Such aging effects could change the characteristics of those systems, which, in isolation or in combination with one or more other specific failures or events, could result in failure of certain life limited parts, which could reduce the structural integrity of the airplane or reduce the controllability of the airplane.
AD 2015-16-05 · published Aug 17, 2015, effective Sep 21, 2015
British Aerospace Regional Aircraft Airplanes
We are adopting a new airworthiness directive (AD) for British Aerospace Regional Aircraft Jetstream Series 3101 and Jetsream Model 3201 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as missing countersunk washers under the head of the main landing gear trunnion cap tension bolts that could cause fatigue in the bolt shanks. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2015-16-06 · published Aug 17, 2015, effective Sep 21, 2015
British Aerospace Regional Aircraft Airplanes
We are adopting a new airworthiness directive (AD) for British Aerospace Regional Aircraft Model Jetstream Model 3201 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the in-service special detailed inspection technique required for the Jetstream 3200's life extension program was delayed; consequently, the in-service special detailed inspection technique is not formally part of the life extension program and may therefore not be accomplished as intended. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2015-16-07 · published Aug 17, 2015, effective Aug 18, 2015
REIMS AVIATION S.A. Airplanes
We are adopting a new airworthiness directive (AD) for REIMS AVIATION S.A. Model F406 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as detachment of the pilot's rudder control pedal in flight. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2015-17-04 · published Aug 20, 2015, effective Sep 24, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by reports of a disconnect between the elevator lever and control rod. This AD requires replacement of left and right fixed control rods and lever assemblies of the elevator control system. We are issuing this AD to prevent a disconnect between the elevator lever and control rod, which could lead to un-commanded elevator movement of the associated control surface, a large difference between the position of the left and the right elevator control surfaces, and consequent reduced controllability of the airplane and degradation of the structural integrity of the horizontal stabilizer.
AD 2015-17-06 · published Aug 20, 2015, effective Sep 24, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A319, A320, and A321 series airplanes. This AD was prompted by reports that on airplanes equipped with sharklets, discretes (used to activate the load alleviation function) are connected on various flight computers using the same ground point. In these cases, the ground point segregation is no longer effective, and a single failure could lead to loss of sharklet identification by flight computers causing a return to the wing tip fence (no sharklet configuration) performance. This AD requires modification of the sharklet ground connection. We are issuing this AD to prevent loss of sharklet identification by the flight computers and subsequent reduced control of the airplane.
AD 2015-17-09 · published Aug 20, 2015, effective Sep 24, 2015
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 98-18-02 for certain Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model C4-605R variant F airplanes (collectively called A300-600 series airplanes). AD 98-18-02 required inspections to detect cracks in the center spar sealing angles adjacent to the pylon rear attachment and in the adjacent butt strap and skin panel, and correction of discrepancies. This new AD continues to require inspections for cracks. This new AD also requires a modification by cold expansion of the center spar sealing angles, replacement of both sealing angles and cold expansion of the attachment holes if necessary, and post-repair repetitive inspections and corrective actions if necessary. This AD was prompted by reports of cracking in the vertical web of the center spar sealing angles of the wing, and subsequent analyses that showed that the inspection threshold and interval specified in AD 98-18-02 must be reduced to allow timely detection of cracks on the sealing angles of the center spar, adjacent to rib 8. We are issuing this AD to prevent crack formation in the sealing angles, which could rupture the sealing angle and lead to subsequent crack formation in the bottom skin of the wing, and result in reduced structural integrity of the center spar section of the wing.
AD 2015-16-08 · published Aug 25, 2015, effective Sep 29, 2015
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2011-08-51 for certain The Boeing Company Model 737-300, -400, and -500 series airplanes. AD 2011-08-51 required repetitive inspections of the lap joint at certain stringers along the entire length from certain body stations. This new AD expands the inspection area, requires additional inspections for cracks and open pockets, requires corrective actions if necessary, and revises the compliance times. This AD was prompted by an evaluation by the design approval holder (DAH) that has determined that the lower fastener holes in the lower skin of the fuselage lap splice are subject to widespread fatigue damage (WFD). We are issuing this AD to detect and correct fatigue cracking of the lower fastener holes in the lower skin of the fuselage lap splice, which could result in reduced structural integrity of the airplane.
AD 2015-17-05 · published Aug 25, 2015, effective Sep 29, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by a report of several events where pilots experienced difficulty in lateral control of the airplane after doing a climb through heavy rain conditions and a determination that the cause was water ingress in the aileron control pulley assembly. This AD requires, for certain airplanes, inspecting for correct clearance and rework if necessary, and, for certain other airplanes, installing a cover for the aileron pulley assembly. We are issuing this AD to prevent water ingress in the aileron control pulley assembly, which could freeze in cold conditions and result in reduced control of the airplane.
AD 2015-17-07 · published Aug 25, 2015, effective Sep 29, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A300 B4-603, B4-605R, B4-620, B4-622, B4-622R airplanes; all Airbus Model A300 C4-605R Variant F airplanes; and certain Airbus Model A300 F4-605R airplanes. This AD was prompted by the manufacturer's review of all repairs accomplished using the structural repair manual. This review was done using revised fatigue and damage tolerance calculations. This AD requires an inspection of the surrounding panels of the left and right forward passenger doors, and corrective actions if necessary. We are issuing this AD to detect and correct previous incomplete or inadequate repairs to the surrounding panels of the left and right forward passenger doors and the fail-safe ring, which could negatively affect the structural integrity of the airplane.
AD 2015-17-08 · published Aug 25, 2015, effective Sep 29, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by an in-service report of an uncommanded and unannunciated nose wheel steering during airplane pushback from the gate. This AD requires installing new cable assemblies with a pull-down resistor. We are issuing this AD to prevent an uncommanded nose wheel steering during takeoff or landing in the event of an open circuit in the steering system, and possible consequent runway excursion.
AD 2015-17-10 · published Aug 25, 2015, effective Sep 29, 2015
SOCATA Airplanes
We are superseding Airworthiness Directive (AD) 2007-04-13 for certain SOCATA Model TBM 700 airplaness (type certificate previously held by EADS SOCATA). This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks found on the main landing gear cylinders. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2015-17-12 · published Aug 25, 2015, effective Sep 29, 2015
Cessna Aircraft Company Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company Model 500, 501, 550, 551, S550, 560, and 650 airplanes. This AD was prompted by reports of smoke and/or fire in the tailcone caused by sparking due to excessive wear of the brushes in the air conditioning (A/C) motor. This AD requires inspections to determine if certain A/C compressor motors are installed and to determine the accumulated hours on certain A/C compressor motor assemblies; and repetitive replacement of the brushes in the A/C compressor motor assembly, or, as an option to the brush replacement, deactivation of the A/C system and placard installation; and return of replaced brushes to Cessna. We are issuing this AD to prevent the brushes in the A/C motor from wearing down beyond their limits, which could result in the rivet in the brush contacting the commutator, causing sparks and consequent fire and/or smoke in the tailcone with no means to detect or extinguish the fire and/or smoke.
AD 2015-17-14 · published Aug 28, 2015, effective Oct 2, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A319, A320, and A321 series airplanes. This AD was prompted by reports that during a full scale fatigue test, several broken frames in certain areas of the cargo compartment have been found, especially on the cargo floor support fittings and open tack holes on the left-hand side. This AD requires a rototest inspection of the open tack holes and rivet holes at the cargo floor support fittings of the fuselage, including doing all applicable related investigative actions, and repair if necessary. We are issuing this AD to detect and correct cracking in the open tack holes and rivet holes at the cargo floor support fittings of the fuselage, which could affect the structural integrity of the airplane.
AD 2015-17-15 · published Aug 28, 2015, effective Oct 2, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL- 600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by results of a design review indicating that the burst pressure of the flexible hose, used to vent oxygen from the high-pressure relief valve of the oxygen cylinder overboard, was lower than the opening pressure of the high-pressure relief valve, which could cause the flexible hose to burst before it can vent the excess oxygen overboard. This AD requires replacing the oxygen hose assembly with a new, improved assembly. We are issuing this AD to prevent the accumulation of oxygen in an enclosed space, which could result in an uncontrolled oxygen-fed fire if an ignition source is nearby.
AD 2015-17-16 · published Aug 28, 2015, effective Oct 2, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by results of a design review indicating that the burst pressure of the flexible hose, used to vent oxygen from the high-pressure relief valve of the oxygen cylinder overboard, was lower than the opening pressure of the high-pressure relief valve, which could cause the flexible hose to burst before it can vent the excess oxygen overboard. This AD requires replacing the oxygen hose assembly with a new, improved assembly. We are issuing this AD to prevent the accumulation of oxygen in an enclosed space, which could result in an uncontrolled oxygen-fed fire if an ignition source is nearby.
AD 2015-17-01 · published Aug 20, 2015, effective Sep 24, 2015
Airbus Helicopters (Previously Eurocopter France) (Airbus Helicopters) Helicopters
We are superseding Airworthiness Directive (AD) 2013-21-01 for Eurocopter France Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters. AD 2013-21-01 required certain inspections of each tail rotor pitch horn assembly (pitch horn) for a crack, replacing a cracked pitch horn before further flight, and a one-time visual inspection of pitch horns above certain hours time-in-service (TIS). This new AD retains the requirements of AD 2013-21-01 but requires a repetitive visual inspection for all pitch horns regardless of hours TIS. This AD was prompted by a report of a crack in the yoke of a pitch horn and is intended to detect a crack in the pitch horn to prevent failure of the pitch horn, loss of the anti-torque function, and subsequent loss of control of the helicopter.
AD 2015-17-02 · published Aug 20, 2015, effective Sep 24, 2015
Bell Helicopter Textron Canada (Bell) Helicopters
We are superseding Airworthiness Directive (AD) 2001-13-51 for Bell Model 206L-4, 407, and 427 helicopters. AD 2001-13-51 required inspecting certain driveshafts for a crack, a loose bolt or nut, or red powder residue and replacing a driveshaft if there is a crack, a loose bolt or nut, or red powder residue. AD 2001-13-51 also required notifying the FAA within 10 days if a crack is found in the driveshaft. This new AD retains the inspection requirement of AD 2001-13-51, expands the applicability to include the Model 429 helicopter, and removes the reporting requirement. This AD is intended to prevent failure of a driveshaft, loss of drive to the main rotor system, and a subsequent emergency landing.
AD 2015-17-11 · published Aug 25, 2015, effective Sep 29, 2015
Airbus Helicopters
We are adopting a new airworthiness directive (AD) for Airbus Helicopters Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, AS355NP, EC130B4, and EC130T2 helicopters. This AD requires inspecting the swashplate assembly rotating star to determine whether a ferrule was installed. If a ferrule exists, this AD requires inspecting the rotating star for a crack and removing any cracked rotating star. This AD was prompted by a report that reconditioning the rotating swashplate per a certain repair procedure could result in the rotating star cracking. The actions of this AD are intended to detect a crack in the rotating star and prevent failure of the rotating star and subsequent loss of control of the helicopter.
AD 2015-16-03 · published Aug 11, 2015, effective Sep 15, 2015
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce plc (RR) RB211-524B-02, RB211-524B2-19, RB211-524B3-02, RB211-524B4-02, RB211-524B4-D-02, RB211-524C2-19, RB211-524D4-19, RB211-524D4-39, and RB211-524D4X-19 turbofan engines. This AD requires removing affected high-pressure turbine (HPT) blades. This AD was prompted by several failures of affected HPT blades. We are issuing this AD to prevent failure of the HPT blade, which could lead to failure of one or more engines, loss of thrust control, and damage to the airplane.
AD 2015-17-20 · published Aug 27, 2015, effective Oct 1, 2015
GE Aviation Czech s.r.o. Turboprop Engines
We are adopting a new airworthiness directive (AD) for certain serial number (S/N) GE Aviation Czech s.r.o. M601E-11, M601E-11A, and M601F turboprop engines with certain part number (P/N) gas generator turbine (GGT) blades, installed. This AD requires removing from service any affected engine with certain GGT blades installed. This AD was prompted by the determination that certain GGT blades are susceptible to blade failure. We are issuing this AD to prevent GGT blade failure, which could lead to engine failure and loss of the airplane.
AD 2015-17-17 · published Aug 28, 2015, effective Oct 2, 2015
Pratt & Whitney Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Pratt & Whitney (PW) PW4164-1D, PW4168-1D, PW4168A-1D and PW4170 engines, and certain PW4164, PW4168, and PW4168A turbofan engines. This AD was prompted by fuel nozzle-to-fuel supply manifold interface fuel leaks. This AD requires inspecting fuel nozzles for signs of leakage, replacing hardware as required, and torqueing to specified requirement. We are issuing this AD to prevent fuel leaks which could result in engine fire and damage to the airplane.
AD 2015-17-18 · published Aug 28, 2015, effective Oct 2, 2015
Turbomeca S.A. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arrius 2F turboshaft engines with a certain part number oil pump installed. This AD requires inspection, and if necessary, replacement before further flight of the oil pump driver assembly and/ or the oil pump shaft, or the oil pump itself. This AD was prompted by cases of deterioration of the gas generator front bearing due to a link loss between the pump driver and the oil pump shaft. We are issuing this AD to prevent link loss between the pump driver and the oil pump shaft, which could lead to an engine in-flight shutdown, forced landing, and damage to the helicopter.
AD 2015-16-04 · published Aug 11, 2015, effective Sep 15, 2015
Kidde Graviner
We are adopting a new airworthiness directive (AD) for certain Kidde Graviner hand-operated fire extinguishers. This AD was prompted by a report that a fire extinguisher failed to operate when the activation lever was pressed. This AD requires modifying the affected fire extinguishers. We are issuing this AD to prevent fire extinguishers from failing to operate in the event of a fire, which could jeopardize occupants' safety and continuation of safe flight and landing.
