20 Airworthiness Directives: 17 airplane, 1 rotorcraft, 1 engine, 1 various.
AD 2015-06-08 · published Apr 9, 2015, effective May 14, 2015
Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Airplanes
We are superseding Airworthiness Directive (AD) 2011-09-03 for all Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Model 382, 382B, 382E, 382F, and 382G airplanes. AD 2011-09-03 required repetitive eddy current inspections to detect cracks in the center wing upper and lower rainbow fittings, and corrective actions if necessary; and repetitive replacement of rainbow fittings, which would extend the repetitive interval for the next inspection. This new AD requires reduced intervals for inspections of the upper rainbow fittings. This AD was prompted by analysis of in-service cracking, which has shown that a reduction in the inspection intervals is necessary for the upper rainbow fittings. We are issuing this AD to detect and correct fatigue cracking of the upper and lower rainbow fittings on the center wings, which could grow large and lead to the failure of the fitting and a catastrophic failure of the center wing.
AD 2015-07-03 · published Apr 9, 2015, effective Apr 24, 2015
Cessna Aircraft Company Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 402C and 414A airplanes. This AD requires repetitively inspecting the engine mount beams for cracks and contacting Cessna for FAA-approved corrective action if cracks are found. This AD also requires sending an inspection report to the FAA and to Cessna. This AD was prompted by reports of cracks found across the engine mount beams. We are issuing this AD to correct the unsafe condition on these products.
AD 2015-07-06 · published Apr 9, 2015, effective May 14, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, F4- 605R, F4-622R, and C4-605R Variant F airplanes; and Model A310-203, - 204, -221, -222, -304, -322, -324, and -325 airplanes. This AD was prompted by a report of inner skin disbonding damage on a rudder. This AD requires repetitive ultrasonic inspections for disbonding of certain rudders; an elasticity of laminate checker inspection; a woodpecker or tap test inspection; venting the core, if necessary; and repairing, if necessary. We are issuing this AD to detect and correct rudder disbonding, which could affect the structural integrity of the rudder.
AD 2015-07-04 · published Apr 14, 2015, effective May 19, 2015
Pilatus Aircraft Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for PILATUS Aircraft Ltd. Model PC-7 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the potential for a spring on the air conditioning compressor clutch plate to shear the oil cooler inlet-hose due to the close routing of these parts without a protective cover. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2015-07-05 · published Apr 14, 2015, effective May 19, 2015
BAE Systems (Operations) Limited Airplanes
We are adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 series airplanes, and Model Avro 146-RJ series airplanes. This AD was prompted by a report of a pressurization problem on an airplane during climb-out; a subsequent investigation showed a crack in the fuselage skin. This AD requires require repetitive external eddy current inspections on the aft skin lap joints of the rear fuselage for cracking, corrosion, and other defects, and repair if necessary. We are issuing this AD to detect and correct cracking, corrosion, and other defects, which could affect the structural integrity of the airplane.
AD 2015-07-07 · published Apr 14, 2015, effective May 19, 2015
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200, -200LR, -300ER, and 777F series airplanes. This AD was prompted by a report of a jettison fuel pump that was shut off by the automatic shutoff system during the center tank fuel scavenge process on a short-range flight and a subsequent failure analysis of the fuel scavenge system. This AD requires making wiring changes, modifying certain power panels, installing electrical load management system 2 (ELMS2) software, and accomplishing a functional test. We are issuing this AD to prevent extended dry running of the jettison fuel pumps, which can be a potential ignition source inside the main fuel tanks, and consequent fuel tank fire or explosion in the event that the jettison pump overheats or has an electrical fault.
AD 2015-08-02 · published Apr 14, 2015, effective Apr 29, 2015
Dassault Aviation Airplanes
We are superseding Airworthiness Directive (AD) 2015-02-04 for certain Dassault Aviation Model MYSTERE-FALCON 50 airplanes. AD 2015- 02-04 required installing two protective plates between the electrical wiring under the glare shield and the engine fire pull handles. This new AD continues to require installing two protective plates between the electrical wiring under the glare shield and the engine fire pull handles. This AD was prompted by our determination that the published version of AD 2015-02-04 incorrectly identified the AD number as "AD 2014-02-04" in a certain paragraph. We are issuing this AD to prevent chafing of the electrical wiring, which could result in a short circuit and generation of smoke in the cockpit, potential loss of several functions essential for safe flight, and consequent reduced controllability of the airplane.
AD 2015-06-10 · published Apr 20, 2015, effective May 5, 2015
ATR-GIE Avions de Transport Régional Airplanes
We are adopting a new airworthiness directive (AD) for certain ATR-GIE Avions de Transport R[eacute]gional Model ATR72-212A airplanes. This AD requires inspection of the shock mount pick-up fittings and cone bolts, and replacement of certain shock mount pick-up fittings if necessary. This AD was prompted by reports of several cases of engine shock mount pick-up fittings with cracks or failure on the engine left- hand (LH) aft side attachment. We are issuing this AD to detect and correct an aft side attachment pick-up fitting failure associated with a cone bolt failure that could reduce the structural integrity of the concerned engine nacelle, and possibly result in detachment of the engine and consequent reduced control of the airplane.
AD 2015-08-01 · published Apr 20, 2015, effective May 26, 2015
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200PF, -200CB, and -300 series airplanes. This AD was prompted by numerous reports of unintended lateral oscillations during final approach, just before landing. This AD requires, depending on airplane configuration, installing new relays and bracket assemblies, inspecting to ensure that the new relays do not contact adjacent wire bundles, torquing the bracket assembly installation nuts and ground stud nuts, doing bond resistance tests between the bracket assemblies and the terminal lugs on the ground studs, and related investigative and corrective actions if necessary. We are issuing this AD to reduce the chance of unintended lateral oscillations near touchdown, which could result in loss of lateral control of the airplane, and consequent airplane damage or injury to flightcrew and passengers.
AD 2015-08-03 · published Apr 21, 2015, effective May 26, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by a report that during production, an incorrect clevis was used, resulting in improper installation onto the alternate release cable of the main landing gear (MLG). This AD requires a detailed visual inspection of the emergency release clevis of the MLG to determine if an incorrect clevis has been installed, and if necessary, replacing the clevis with a correct clevis and clevis pin. We are issuing this AD to detect and correct improper installation of the clevis, which could cause loss of the alternate release system and prevent the MLG from extending and retracting, and could consequently affect the airplane's continued safe flight and landing.
AD 2015-08-05 · published Apr 23, 2015, effective May 8, 2015
Dassault Aviation Airplanes
We are superseding Airworthiness Directive (AD) 2013-26-05 for all Dassault Aviation Model FAN JET FALCON, FAN JET FALCON SERIES C, D, E, F, and G airplanes; Model MYSTERE-FALCON 200 airplanes; and Model MYSTERE-FALCON 20-C5, 20-D5, 20-E5, and 20-F5 airplanes. AD 2013-26-05 required repetitive weighing of fire extinguisher bottles having a certain part number, and eventual replacement of those bottles to terminate the repetitive weighing. This new AD continues to require repetitive weighing of fire extinguisher bottles having a certain part number, and eventual replacement of those bottles to terminate the repetitive weighing. This AD was prompted by our determination that certain text in the method of compliance language specified in AD 2013- 26-05 incorrectly refers to Airbus, instead of "Dassault Aviation." We are issuing this AD to detect and correct a dormant failure in the fire suppression system, which could result in the inability to put out a fire in an engine, auxiliary power unit (APU), or rear compartment.
AD 2015-08-06 · published Apr 27, 2015, effective Jun 1, 2015
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 2007-14-05 for all Airbus Model A310 and Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). AD 2007-14-05 required revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness by incorporating certain certification maintenance requirements. This new AD requires revising the maintenance or inspection program to incorporate more restrictive maintenance requirements and airworthiness limitations. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. We are issuing this AD to prevent safety-significant latent failures that would, in combination with one or more other specific failures or events, result in a hazardous or catastrophic failure condition of avionics, hydraulic systems, fire detection systems, fuel systems, or other critical systems.
AD 2015-08-08 · published Apr 27, 2015, effective May 12, 2015
Airbus Airplanes
We are superseding Airworthiness Directive (AD) 2014-26-53 and AD 2015-03-02 for certain Airbus Model A319-115, A319-133, A320-214, A320-232, and A320-233 airplanes. AD 2014-26-53 required repetitive detailed visual inspections to detect discrepancies of the wing lower skin surface and inboard main landing gear (MLG) support rib lower flange location fasteners and, depending on findings, accomplishment of applicable corrective action(s). AD 2015-03-02 required repetitive detailed visual inspections of the outboard MLG support rib lower flange fasteners for discrepancies, and corrective actions if necessary. This new AD retains the repetitive detailed visual inspections to detect discrepancies of the fasteners located in the wing lower skin surface and inboard MLG support rib lower flange with extended compliance times and repetitive intervals, and accomplishment of applicable corrective actions. This new AD also retains the repetitive detailed visual inspections of the outboard MLG support rib lower flange fasteners for discrepancies, and corrective actions if necessary. In addition, this new AD adds airplanes to the applicability. This AD was prompted by a determination that certain airplanes were missing from the applicability of AD 2014-26-53 and AD 2015-03-02 and that those airplanes may be affected by the unsafe condition addressed in AD 2014-26-53 and AD 2015-03-02. We are issuing this AD to detect and correct discrepancies of the fasteners at the external surface of the lower wing skin and inboard and outboard MLG support rib lower flanges, which could result in an airplane not meeting its maximum loads expected in service. This condition could result in structural failure.
AD 2015-07-02 · published Apr 30, 2015, effective Jun 4, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. This AD was prompted by a determination that the forward lugs of the flap hinge box might not conform to engineering drawings, which could result in premature fatigue cracking. This AD requires revising the maintenance or inspection program to include new airworthiness limitations tasks; and measuring the forward lug edge distance of each flap hinge box, inspecting for cracking and damage (i.e., deformation or bearing failure) of the forward lug edge of each flap hinge box, and repairing any cracking or damage if necessary. We are issuing this AD to detect and correct non-conforming flap hinge box forward lugs, which could result in failure of the lugs and detachment of the flap hinge box and consequent detachment of the flap surface.
AD 2015-08-09 · published Apr 30, 2015, effective Jun 4, 2015
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600 and -700 series airplanes. This AD was prompted by reports of cracking in the body station (STA) 727 bulkhead lower frame. This AD requires a detailed and open hole high frequency eddy current (HFEC) inspection of the left- and right-side lower frame webs and inner chords for cracking, and corrective actions and preventative modifications if necessary. This AD also provides for optional terminating action of the repetitive inspections, under certain conditions. We are issuing this AD to detect and correct cracking in a bulkhead lower frame web and inner chord, which could result in a severed frame and induced skin cracks, and could lead to rapid decompression of the fuselage.
AD 2015-09-02 · published Apr 30, 2015, effective Jun 4, 2015
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD was prompted by a determination that without an effective maintenance task to maintain the airplane's inherent level of safety, there is a potential that a dormant failure of the alternate release system of the landing gear could occur. This AD requires revising the maintenance or inspection program, as applicable, to incorporate a maintenance task for an operational check of the electro- mechanical actuator and release mechanism of the alternate extension system for the nose landing gear and main landing gear. We are issuing this AD to prevent failure of the alternate release system of the landing gear, which could prevent the landing gear from extending during a failure of the normal landing gear extension system.
AD 2015-09-03 · published Apr 30, 2015, effective Jun 4, 2015
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A318-111 and -112 airplanes and Model A319, A320, and A321 series airplanes. This AD was prompted by reports of cracks on the forward corner fittings of engine pylon aft secondary structures. This AD requires repetitive inspections of certain forward corner fittings of the pylon aft secondary structures, and corrective actions if necessary. This AD also provides optional terminating action for the repetitive inspections. We are issuing this AD to detect and correct detachment of the lower fairing attachment and/or loss of the aft fixed fairing with the movable fairing from the airplane in flight, which could result in damage to the airplane.
AD 2015-05-52 · published Apr 14, 2015, effective Apr 29, 2015
Agusta S.p.A. Helicopters
We are publishing a new airworthiness directive (AD) for Agusta S.p.A. (Agusta) Model A109, A109A, A109A II, A109C, A109K2, A109E, A119, A109S, AW119 MKII, and AW109SP helicopters, which was sent previously to all known U.S. owners and operators of these helicopters. This AD requires inspecting certain tail rotor (T/R) pitch control links (pitch links) for freedom of movement, corrosion, excessive friction of the spherical bearings, and cracks. This AD is prompted by a report of an in-flight failure of a pitch link on an Agusta Model AW119 MKII helicopter. These actions are intended to prevent loss of T/ R pitch control and subsequent loss of control of the helicopter.
AD 2015-07-01 · published Apr 3, 2015, effective May 8, 2015
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Rolls-Royce plc (RR) RB211-524 turbofan engines with certain part number (P/N) low-pressure turbine (LPT) stage 3 turbine blades installed. This AD requires implementation of a life limit for certain P/N LPT stage 3 turbine blades and replacement of affected blades that reach or exceed the life limit. This AD was prompted by reports of LPT stage 3 turbine blade failures, release of blades, and subsequent in- flight shutdowns. We are issuing this AD to prevent failure of LPT stage 3 turbine blades and subsequent release of blade debris, which could lead to failure of one or more engines, loss of thrust control, and damage to the airplane.
AD 2015-08-04 · published Apr 29, 2015, effective Jun 3, 2015
Various Aircraft Equipped With Wing Lift Struts
We are superseding Airworthiness Directive (AD) 99-01-05 R1, which applied to certain aircraft equipped with wing lift struts. AD 99-01-05 R1 required repetitively inspecting the wing lift struts for corrosion; repetitively inspecting the wing lift strut forks for cracks; replacing any corroded wing lift strut; replacing any cracked wing lift strut fork; and repetitively replacing the wing lift strut forks at a specified time for certain airplanes. This new AD retains all requirements of AD 99-01-05R1 and adds additional airplane models to the Applicability section. This AD was prompted by a report that additional Piper Aircraft, Inc. model airplanes should be added to the Applicability section. We are issuing this AD to correct the unsafe condition on these products.
