37 Airworthiness Directives: 19 airplane, 10 rotorcraft, 6 engine, 2 glider.
AD 2013-22-11 · published Nov 5, 2013, effective Dec 10, 2013
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2009-10-06 for certain The Boeing Company Model 747-400 and -400D series airplanes. AD 2009-10-06 required repetitive inspections to detect cracks in the floor panel attachment fastener holes of the Section 41 upper deck floor beam upper chords, and corrective actions if necessary; and repetitive post-repair and post-modification inspections, and corrective actions if necessary. This new AD adds repetitive inspections of Section 44 upper deck floor beam upper chords, and corrective actions if necessary; repetitive post-repair and post- modification inspections, and corrective actions if necessary; and replacement of the upper deck floor beam upper chords. This AD was prompted by an evaluation by the design approval holder (DAH) indicating that certain upper chords of the upper deck floor beam are subject to widespread fatigue damage (WFD). We are issuing this AD to detect and correct fatigue cracking in certain upper chords of the upper deck floor beam, which could become large and cause the floor beams to become severed and result in rapid decompression or reduced controllability of the airplane.
AD 2013-22-18 · published Nov 5, 2013, effective Nov 20, 2013
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Airplanes
We are adopting a new airworthiness directive (AD) for certain Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135ER, - 135KE, -135KL, and -135LR airplanes; and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP airplanes. This AD requires repetitive detailed inspections to detect discrepancies on the attaching parts of the lower eyelet fitting of the cockpit windshield center-post, and, if no discrepancy is found, a check to make sure the bolts are tight, and replacement of the attaching parts if necessary. This AD also provides an option to accomplish the replacement of the attaching parts, which terminates the repetitive inspections. This AD was prompted by reports of failure of the bolts that connect the lower eyelet fitting of the cockpit windshield center-post to the forward fuselage. We are issuing this AD to detect and correct failed bolts and attaching parts of the lower eyelet fitting of the cockpit windshield center-post, which could lead to loss of structural integrity of the airplane.
AD 2013-22-13 · published Nov 8, 2013, effective Nov 29, 2013
PILATUS Aircraft Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for certain PILATUS Aircraft Ltd. Model PC-7 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as chafing on the wiring harness attached to the engine mounting frame on the right-hand side of the engine compartment, which could cause a short circuit and could result in a fire in the engine compartment. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-22-20 · published Nov 8, 2013, effective Nov 8, 2013
Embraer S.A. Airplanes
We are adopting a new airworthiness directive (AD) for Embraer S.A. Model EMB-505 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracking in the stator pressure plate of the brake assembly, which may lead to loss of brake parts on the runway and reduced brake capability with possible runway excursion. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-14-04 · published Nov 14, 2013, effective Dec 19, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-223F, -223, -321, -322, and -323 airplanes. This AD was prompted by fatigue load analysis that determined that the inspection interval for certain pylon bolts must be reduced. This AD requires a torque check of forward engine mount bolts, and replacement if necessary. We are issuing this AD to detect and correct loose or broken bolts, which could lead to engine detachment in-flight, and damage to the airplane.
AD 2013-19-14 · published Nov 14, 2013, effective Dec 19, 2013
Airbus Airplanes
We are superseding Airworthiness Directives (ADs) 2009-04-07 and 2011-02-09 for certain Airbus Model A330-200, A330-200 Freighter, A300-300, A340-200, A340- 300, A340-500, and A340-600 series airplanes. AD 2009-04-07 required revising the airplane flight manual (AFM) to include appropriate operational procedures to prevent the air data inertial reference unit (ADIRU) from providing erroneous data to other airplane systems. AD 2011-02-09 required revising the AFM to provide appropriate operational procedures to prevent the airplane flight directors (FDs), autopilot (AP), and auto-thrust re-engagement in the event of airspeed sources providing similar but erroneous data. This new AD requires that operators modify or replace all three flight control primary computers (FCPCs) with new software standards. Since we issued ADs 2009-04-07 and 2011-02-09, we have determined that new software standards for the FCPCs are necessary to inhibit autopilot re-engagement under unreliable airspeed conditions. This new AD also removes certain airplanes from the applicability. We are issuing this AD to prevent autopilot engagement under unreliable airspeed conditions, which could result in reduced controllability of the airplane.
AD 2013-22-10 · published Nov 14, 2013, effective Dec 19, 2013
Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model Fan Jet Falcon; Model Mystere-Falcon 200 airplanes; and Model Mystere-Falcon 20-C5, 20-D5, 20-E5, and 20-F5 airplanes. This AD was prompted by reports of defective fire extinguisher bottle cartridges. This AD requires checking manufacturing references of pyrotechnical cartridges for batch number and date, repetitive checking of cartridges for electrical continuity, and replacing defective pyrotechnical cartridges if necessary. We are issuing this AD to detect and correct defective fire bottle cartridges, which could impact the capability to extinguish a fire in an engine, auxiliary power unit, or rear compartment, which could result in damage to the airplane and injury to the occupants.
AD 2013-22-23 · published Nov 14, 2013, effective Dec 16, 2013
Aermacchi S.p.A. Airplanes
We are adopting a new airworthiness directive (AD) for Aermacchi S.p.A. Models F.260, F.260B, F.260C, F.260D, F.260E, F.260F, S.208, and S.208A airplanes equipped with a Lycoming O-540 wide cylinder flange engine with a front crankcase mounted propeller governor. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the set screw that fixes the setting of the propeller governor idler gear shaft was not in the proper position. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-23-03 · published Nov 14, 2013, effective Nov 29, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, and 747SR series airplanes. This AD requires inspecting to determine the part number of the inboard actuator attach fittings of the outboard flap. For affected attach fittings, this AD requires doing a detailed inspection of the attach fittings for a cylindrical defect and replacing if necessary. As an option to the detailed inspection, this AD allows replacement of affected attach fittings. This AD was prompted by a report of the fracture of an inboard actuator attach fitting of the outboard flap. An inspection of the attach fitting revealed that it was incorrectly machined with a cylindrical profile instead of a conical profile, resulting in reduced wall thickness. We are issuing this AD to detect and correct defective inboard actuator attach fittings which, combined with loss of the outboard actuator load path, could result in uncontrolled retraction of the outboard flap, damage to flight control systems, and consequent reduced controllability of the airplane.
AD 2013-23-02 · published Nov 15, 2013, effective Dec 2, 2013
EADS CASA (Type Certificate Previously Held by Construcciones Aeronauticas, S.A.) Airplanes
We are adopting a new airworthiness directive (AD) for all EADS CASA (Type Certificate previously held by Construcciones Aeronauticas, S.A.) Model CN-235, CN-235-100, CN-235-200, CN-235-300, and C-295 airplanes. This AD requires inspection of the feeder cables of certain fuel booster pumps for damage (including, but not limited to, signs of electrical arcing and fuel leaks), and replacement if necessary. This AD was prompted by a report of an in-flight problem with the fuel transfer system. We are issuing this AD to detect and correct damage to certain fuel booster pumps, which could create an ignition source in the fuel tank vapor space, and result in a fuel tank explosion and consequent loss of the airplane.
AD 2013-23-04 · published Nov 15, 2013, effective Dec 20, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -800, -900, and -900ER series airplanes. This AD was prompted by reports that certain seat track bolts were found with severed head bolts due to fatigue. This AD requires replacing titanium seat track bolts with corrosion resistant steel (CRES) bolts, repetitive inspections for cracking of the splice strap and forward seat track holes, and related investigative and corrective actions if necessary. This AD also provides an optional terminating action for the repetitive inspections. We are issuing this AD to detect and correct missing or severed bolt heads, which, if not corrected, could result in the inability of the seat track to carry passenger loads, which could cause the seats to detach from the seat track, resulting in possible injury to passengers during an emergency landing or survivable crash.
AD 2013-23-05 · published Nov 15, 2013, effective Dec 20, 2013
Fokker Services B.V. Airplanes
We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by a design review, which revealed that, under certain failure conditions, wiring in the main fuel tank could develop a short circuit that might cause a hot spot on the wiring conduit or puncture the wiring conduit wall. This AD requires installing fuses in the power supply wiring and/or return wiring for various components in the fuel system; and revising the airplane maintenance program by incorporating critical design configuration control limitations. We are issuing this AD to prevent an ignition source in the main fuel tank vapor space, which could result in a fuel tank explosion and consequent loss of the airplane.
AD 2013-23-06 · published Nov 25, 2013, effective Dec 30, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757-200 and -200PF series airplanes. This AD was prompted by reports indicating that a standard access door was located where an impact-resistant access door was required, and stencils were missing from some impact-resistant access doors. This AD requires an inspection of the left- and right-hand wing fuel tank access doors to determine that impact-resistant access doors are installed in the correct locations, and to replace any door with an impact-resistant access door if necessary. This AD also requires an inspection for stencils and index markers on impact-resistant access doors, and application of new stencils or index markers if necessary. This AD also requires revising the maintenance program to incorporate changes to the airworthiness limitations section. We are issuing this AD to prevent foreign object penetration of the fuel tank, which could cause a fuel leak near an ignition source (e.g., hot brakes or engine exhaust nozzle), consequently leading to a fuel-fed fire.
AD 2013-23-08 · published Nov 25, 2013, effective Dec 30, 2013
AQUILA-Aviation by Excellence AG Airplanes
We are adopting a new airworthiness directive (AD) AQUILA-- Aviation by Excellence AG Model AT01 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a defective sealing of a tapped through bore hole at the inside of the fuel tank openings in combination with prolonged periods at maximum fuel level. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-23-13 · published Nov 25, 2013, effective Dec 30, 2013
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A300 series airplanes; Model A300 B4-600, B4-600R, and F4- 600R series airplanes; and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a report that cracking was found in area 2 of the frame base fittings between frame 41 and frame 46. This AD requires a check of maintenance records to determine if certain repairs were done in area 1 of the frame base fittings, and, for affected airplanes, a detailed inspection for cracking in area 2 of the frame base fittings between frame 41 and frame 46, and repair if necessary. We are issuing this AD to detect and correct cracking in area 2 of the frame base fittings between frame 41 and frame 46, which could adversely affect the structural integrity of the airplane.
AD 2013-23-15 · published Nov 25, 2013, effective Dec 30, 2013
The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2009-06-02, which applied to certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747SR, and 747SP series airplanes. AD 2009-06-02 required repetitive inspections for skin cracks at the shear tie end fastener locations of the fuselage frames, and repair of cracks if necessary. This new AD also requires repetitive inspections for skin cracks next to the shear tie on airplanes with certain existing repair doublers, and corrective actions if necessary. This AD also revises the applicability to include additional airplanes. This AD was prompted by additional cracking found on an airplane not affected by AD 2009-06-02. We are issuing this AD to detect and correct fatigue cracks in the fuselage skin that can propagate and grow, and result in reduced structural integrity and sudden decompression of the airplane in flight.
AD 2013-23-16 · published Nov 25, 2013, effective Dec 30, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 757 airplanes. This AD was prompted by a report of a broken forward support fitting at the inboard track of the inboard flap. This AD requires repetitive inspections of the forward support fitting assemblies of the inboard track of the left and right inboard flaps for cracking, and corrective actions if necessary. We are issuing this AD to detect and correct cracking of the forward support fitting assembly, which could result in loss of inboard flap control and subsequent loss of airplane control.
AD 2013-23-19 · published Nov 25, 2013, effective Nov 25, 2013
XtremeAir GmbH Airplanes
We are adopting a new airworthiness directive (AD) for XtremeAir GmbH Model XA42 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracks in a weld seam between the lower left landing gear attachment bearing and the lower engine mount to the firewall attachment plate, which could reduce the structural integrity of the airplane and could result in engine separation. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-24-01 · published Nov 27, 2013, effective Nov 27, 2013
The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for The Boeing Company Model 747-8 and 747-8F series airplanes and Model 787-8 airplanes powered by GEnx engines. This AD requires revising the airplane flight manual to advise the flight crew of potential ice crystal icing (ICI) conditions at high altitudes, and to prohibit operation in moderate and severe ICI conditions. This AD also requires inspecting the engine after any ICI event is detected by the flight crew. This AD was prompted by reports of engine damage and thrust loss events as a result of flying in high altitude ICI conditions. We are issuing this AD to ensure that the flight crews have operating instructions to avoid flight into ICI conditions that can lead to engine damage and thrust loss events; unrecoverable thrust loss on multiple engines can lead to a forced landing.
AD 2013-22-17 · published Nov 4, 2013, effective Dec 9, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS332C, AS332L, AS332L1, AS332L2, and EC225LP helicopters. This AD requires inspecting the intermediate gearbox (IGB) fairing for a crack and inspecting the IGB fairing gutter (gutter), if installed, for a crack, separation, or interference. This AD is prompted by reports of cracks, separation of the IGB fairing from the gutter and attachment supports, and subsequent interference with the tail rotor (T/R) inclined drive shaft. These actions are intended to detect a crack and prevent separation of the IGB fairing, which could result in interference with the T/R inclined drive shaft and subsequent loss of control of the helicopter.
AD 2013-20-13 · published Nov 5, 2013, effective Dec 10, 2013
Bell Helicopter Textron Canada Limited (Bell) Helicopters
We are adopting a new airworthiness directive (AD) for certain Bell Model 206B and 206L helicopters. This AD requires installing a placard beneath the engine power dual tachometer and revising the operating limitations section of the rotorcraft flight manual (RFM). This AD was prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speeds during steady-state operations. These actions are intended to alert pilots to avoid certain engine speeds during steady- state operations, prevent failure of the third stage engine turbine, engine power loss, and subsequent loss of control of the helicopter.
AD 2013-20-17 · published Nov 8, 2013, effective Dec 13, 2013
Eurocopter Deutschland GmbH (ECD) Helicopters
We are adopting a new airworthiness directive (AD) for ECD Model BO105C (C-2 and CB-2 Variants) and BO105S (CS-2 and CBS-2 Variants) helicopters with a certain third stage turbine wheel installed. This AD requires installing a placard on the instrument panel and revising the limitations section of the rotorcraft flight manual (RFM). This AD is prompted by several incidents of third stage engine turbine wheel failures, which were caused by excessive vibrations at certain engine speeds during steady-state operations. These actions are intended to alert pilots to avoid certain engine speeds during steady-state operations, prevent failure of the third stage engine turbine, engine power loss, and subsequent loss of control of the helicopter.
AD 2013-22-15 · published Nov 8, 2013, effective Dec 13, 2013
Sikorsky Aircraft Corporation (Sikorsky) Helicopters
We are adopting a new airworthiness directive (AD) for Sikorsky Model S-76A, B, and C helicopters to require certain inspections of each spindle cuff assembly or blade fold cuff assembly for a crack. If there is a crack, this AD requires replacing the cracked part. If there is no crack, this AD requires applying white paint to the inspection area to enhance the existing inspection procedure. This AD was prompted by discovery of cracks in the spindle cuffs. The actions are intended to prevent failure of a spindle cuff assembly or blade fold cuff assembly, loss of a rotor blade, and subsequent loss of control of the helicopter.
AD 2013-22-16 · published Nov 8, 2013, effective Dec 13, 2013
Agusta S.p.A. (Type Certificate Currently Held by Agusta Westland) Helicopters
We are adopting a new airworthiness directive (AD) for certain Agusta S.p.A. (Agusta) Model AW139 helicopters. This AD requires replacing certain solder splices in the co-pilot audio system. This AD was prompted by the discovery of improper installation of solder splices on the co-pilot audio system causing intermittent noise through the audio system during flight. The actions of this AD are intended to prevent degradation and complete loss of communications between the pilot and co-pilot during flight, impairing the co-pilot's capability to react immediately to operational difficulties, which could lead to subsequent loss of control of the helicopter.
AD 2013-22-21 · published Nov 8, 2013, effective Dec 13, 2013
Bell Helicopter Textron, Inc., Helicopters
We are adopting a new airworthiness directive (AD) for Bell Helicopter Textron, Inc. (Bell), Model 206A, 206B, 206L, 206L-1, 206L- 3, 206L-4, and 407 helicopters with an Apical Industries, Inc. (Apical) emergency float kit installed under Supplemental Type Certificate (STC) Number SR01535LA. This AD was prompted by an incident in which the floats installed on a helicopter failed to deploy. This AD requires inspecting, labeling, and replacing the float inflation hoses. We are issuing this AD to prevent failure of the emergency floatation gear to deploy during an emergency event.
AD 2013-23-07 · published Nov 22, 2013, effective Dec 27, 2013
Erickson Air-Crane Incorporated Helicopters (Type Certificate Previously Held by Sikorsky Aircraft Corporation)
We are superseding airworthiness directive (AD) 90-26-12 for Sikorsky Aircraft Corporation (Sikorsky) Model S-64E helicopters. AD 90-26-12 required checks of the main rotor blades for a crack. This new AD retains the actions required by AD 90-26-12, reflects that the type certificate (TC) for this model helicopter has been transferred to Erickson Air-Crane Incorporated (Erickson), and expands the applicability to include the similar Erickson Model S-64F helicopters. This AD is prompted by a need to expand the applicability to include Model S-64F helicopters and clarify the applicable main rotor blades by part number. These actions are intended to detect a crack in the main rotor blade and prevent blade separation and subsequent loss of control of the helicopter.
AD 2013-23-09 · published Nov 22, 2013, effective Dec 27, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters with sliding doors, except those with modification AL.4262. This AD requires removing from service certain part-numbered nuts and washers from the lower ball-joint bolt. This AD was prompted by a report of a sliding door detaching from the helicopter in flight. These actions are intended to prevent loss of the lower ball-joint nut, which could lead to loss of the sliding door and damage to the helicopter.
AD 2013-23-10 · published Nov 25, 2013, effective Dec 30, 2013
Eurocopter France Helicopters
We are superseding Airworthiness Directive (AD) 2010- 21-01 for Eurocopter France (Eurocopter) Model AS350B, BA, B1, B2, B3, D, AS355E, F, F1, F2, and N helicopters. AD 2010-21-01 required an inspection to determine whether a cross-member is installed at station X 2165 and doublers at X 2325 and Y 269, and installing them if they are missing. This new AD retains the requirements of AD 2010-21-01 but clarifies the inspection procedures and limits the applicability to only those helicopters with collective-to-yaw control coupling. This AD is prompted by a crack discovered in the area of the center cross-member at station X 2325, at the attachment point of the yaw channel ball-type control sheath stop, of a Model AS355N helicopter fitted with the collective-to-yaw control coupling. The actions of this AD are intended to prevent reduced yaw control and subsequent loss of helicopter control.
AD 2013-23-11 · published Nov 25, 2013, effective Dec 30, 2013
Eurocopter France Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS332L2 and EC225LP helicopters. This AD requires inspecting the torque value of the bolts that secure the front and rear main gearbox (MGB) suspension bar attaching fittings, and re-torqueing the bolts to the proper value if the torque value is out of tolerance. This AD also requires, if the torque value is out of tolerance by more than 20 percent, inspecting the bolts, frames, and related equipment for a crack and repairing or replacing them if cracked. This AD was prompted by reports of cracks on Frame 5295 of Model AS332L2 helicopters. The actions of this AD are intended to detect the torque loss of the bolts that secure the MGB bar attaching fittings and to prevent cracks that could lead to failure of the MGB supporting structure, detachment of the MGB, and loss of helicopter control.
AD 2013-19-17 · published Nov 14, 2013, effective Nov 7, 2013
Rolls-Royce plc Turbofan Engines
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. That AD applies to all Rolls-Royce plc (RR) RB211-535E4-B-37 series turbofan engines. The AD number is incorrect in the Regulatory text. This document corrects that error. In all other respects, the original document remains the same.
AD 2013-22-22 · published Nov 15, 2013, effective Dec 20, 2013
Turbomeca S.A. Turboshaft Engines
We are superseding airworthiness directive (AD) 2013-01-07 for all Turbomeca S.A. Arriel 2D turboshaft engines. AD 2013-01-07 required replacing the hydromechanical metering unit (HMU) at a reduced life. This AD maintains that requirement and also requires conducting inspections of the HMU. This AD was prompted by further cases of deterioration of HMU rotating components. We are issuing this AD to prevent an uncommanded in-flight shutdown of the engine and possible loss of the helicopter.
AD 2013-23-01 · published Nov 25, 2013, effective Dec 30, 2013
Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) model Tay 620-15, 650-15, and 651-54 turbofan engines. This AD requires a one-time inspection of the high-pressure (HP) air bleed valve operating mechanism and, depending on findings, corrective action. This AD was prompted by excessive deterioration of the HP air bleed valve operating mechanism, which is influencing the aerodynamic fan flutter margin. This condition, if not corrected, could lead to multiple fan blade failure. We are issuing this AD to prevent multiple fan blade failure, which could result in uncontained engine failure and damage to the airplane.
AD 2013-24-06 · published Nov 25, 2013, effective Dec 30, 2013
Thielert Aircraft Engines GmbH Reciprocating Engines
We are adopting a new airworthiness directive (AD) for all Thielert Aircraft Engines GmbH TAE 125-01 reciprocating engines. This AD requires applying sealant to close the engine clutch housing (crankcase assembly) opening. This AD was prompted by a report of engine power loss due to engine coolant contaminating the engine clutch. The design of the engine allows the crankcase assembly opening to be susceptible to contamination from external sources. We are issuing this AD to prevent in-flight engine power loss, which could result in loss of control of, and damage to, the airplane.
AD 2013-23-12 · published Nov 26, 2013, effective Dec 11, 2013
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for all Rolls-Royce plc (RR) RB211 Trent 553-61, 553A2-61, 556-61, 556A2-61, 556B-61, 556B2-61, 560-61, and 560A2-61 turbofan engines. This AD requires replacement or repair of the low-pressure (LP) compressor fan blade set before reaching a specified number of flight cycles since new (FCSN) or flight cycles since last leading edge profile blade repair (FCSLR). This AD was prompted by reports of erosion of the leading edge profile of the LP compressor blade set contributing to fan blade flutter. We are issuing this AD to prevent failure of the LP compressor blades, which could lead to an uncontained engine failure and damage to the airplane.
AD 2013-23-17 · published Nov 26, 2013, effective Dec 11, 2013
Rolls-Royce plc Turbofan Engines
We are adopting a new airworthiness directive (AD) for Rolls- Royce plc (RR) RB211-535E4-37, -535E4-B-37, -535E4-C-37, RB211Trent 768-60, 772-60, and 772B-60 turbofan engines. This AD requires removal of certain high-pressure (HP) and intermediate-pressure (IP) turbine discs before their accumulated cyclic lives have reached the revised limits. This AD was prompted by a report of an HP disc contaminated with a steel inclusion. We are issuing this AD to prevent failure of the HP or IP turbine disc, uncontained engine failure, and damage to the airplane.
AD 2013-22-14 · published Nov 4, 2013, effective Nov 25, 2013
DG Flugzeugbau GmbH Gliders
We are adopting a new airworthiness directive (AD) for any DG Flugzeugbau GmbH Model DG-1000T glider equipped with a Solo Kleinmotoren Model 2350 C engine. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as engine shaft failure and consequent propeller detachment. We are issuing this AD to require actions to address the unsafe condition on these products.
AD 2013-22-12 · published Nov 8, 2013, effective Nov 18, 2013
DG Flugzeugbau GmbH Gliders
We are adopting a new airworthiness directive (AD) for all DG Flugzeugbau GmbH Models DG-800A, DG-800B, DG-500MB gliders. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a defective starter motor control unit, which could activate the starter motor without pressing the starter button. We are issuing this AD to require actions to address the unsafe condition on these products.
