31 Airworthiness Directives: 17 airplane, 5 rotorcraft, 9 engine.
AD 2011-21-51 · published Nov 1, 2011, effective Nov 1, 2011
Cessna Aircraft Company Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Model 525C airplanes. This emergency AD was sent previously to all known U.S. owners and operators of these airplanes. This AD requires replacing certain lithium-ion batteries installed as the main aircraft battery with either a Ni-Cad or a lead acid battery. This AD was prompted by a report of a battery fire that resulted after an energized ground power unit was connected to one of the affected airplanes equipped with a lithium-ion battery as the main aircraft battery. We are issuing this AD to correct the unsafe condition on these products.
AD 2011-23-03 · published Nov 1, 2011, effective Dec 6, 2011
SOCATA Airplanes
We are adopting a new airworthiness directive (AD) for certain SOCATA Model TBM 700 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-05 · published Nov 1, 2011, effective Nov 16, 2011
The Boeing Company Model 737-300, -400, and -500 Series Airplanes
We are superseding an existing airworthiness directive (AD) for certain Model 737-300, -400, and -500 series airplanes. That AD currently requires repetitive inspections for cracking of the 1.04-inch nominal diameter wire penetration hole, and applicable related investigative and corrective actions. This AD reduces the compliance times for those actions. This AD was prompted by reports of cracking in the frame, or in the frame and frame reinforcement, common to the 1.04- inch nominal diameter wire penetration hole intended for wire routing; and recent reports of multiple adjacent frame cracking found before the compliance time required by the existing AD. Such cracking could reduce the structural capability of the frames to sustain limit loads, and result in cracking in the fuselage skin and subsequent rapid depressurization of the airplane. We are issuing this AD to correct the unsafe condition on these products.
AD 2011-23-06 · published Nov 4, 2011, effective Nov 21, 2011
Sicma Aero Seat Passenger Seat Assemblies, Installed on, But Not Limited to, ATR-GIE Avions de Transport Régional Airplanes
We are adopting a new airworthiness directive (AD) for Sicma Aero Seat Model 9401, 9402, 9404, 9405, 9406, 9407, 9408, and 9409 series passenger seat assemblies, installed on, but not limited to, ATR-GIE Avions de Transport R[eacute]gional Model ATR42 and ATR72 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-09 · published Nov 4, 2011, effective Dec 9, 2011
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-07 · published Nov 10, 2011, effective Dec 15, 2011
Gulfstream Aerospace LP (Type Certificate Previously Held by Israel Aircraft Industries, Ltd.) Airplanes
We are adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace LP (type certificate previously held by Israel Aircraft Industries, Ltd.) Model Galaxy and Gulfstream G150 airplanes; and Gulfstream Aerospace LP Model Gulfstream 200 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-10 · published Nov 10, 2011, effective Dec 15, 2011
ATR-GIE Avions de Transport Régional Airplanes
We are adopting a new airworthiness directive (AD) for certain Model ATR42 and ATR72 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-11 · published Nov 10, 2011, effective Dec 15, 2011
Pacific Aerospace Limited Airplanes
We are adopting a new airworthiness directive (AD) for Pacific Aerospace Limited Model FU24 Airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-08 · published Nov 17, 2011, effective Dec 22, 2011
Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are superseding an existing airworthiness directive (AD) that applies to certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-24-01 · published Nov 17, 2011, effective Dec 22, 2011
Piaggio Aero Industries S.p.A. Airplanes
We are adopting a new airworthiness directive (AD) for Piaggio Aero Industries S.p.A. Model P-180 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 89-23-19 · published Nov 20, 2011, effective Nov 20, 2011
The Boeing Company Airplanes
AD 2011-24-02 · published Nov 29, 2011, effective Jan 3, 2012
Gulfstream Aerospace Corporation Model GV and GV-SP Airplanes
We are adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GV and GV-SP airplanes. This AD was prompted by notification from the airplane manufacturer that the third fire extinguisher bottle is mounted in a small-fragment impact zone. This AD requires inspecting to determine whether a third Halon fire extinguisher bottle is installed in the auxiliary power unit (APU) fragment impact zone, revising the limitations section of the airplane flight manual to add restrictions for APU usage for certain airplanes having a third fire extinguisher bottle, and removing the third fire extinguisher bottle from certain airplanes. We are issuing this AD to prevent penetration of the bottle by fragments released due to a failure of the APU rotor system. The bottle could rupture and cause substantial damage to primary airframe structure and primary flight controls.
AD 2011-24-03 · published Nov 29, 2011, effective Jan 3, 2012
Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-24-04 · published Nov 29, 2011, effective Jan 3, 2012
McDonnell Douglas Corporation Airplanes
We are adopting a new airworthiness directive (AD) for certain Model DC-10-10, DC-10-10F, and MD-10-10F airplanes. This AD was prompted by reports of three instances of fuel leaks in the lower cap splice of the wing rear spar at station Xors=409. Investigation revealed the fuel leak was due to a crack in the lower cap. If not corrected, this condition could result in fuel leaks or cracking of the lower wing skin and structure, causing possible inability of the structure to sustain the limit load and adversely affecting the structural integrity of the airplane. This AD requires repetitive inspections for cracking on the lower cap of the rear spar of the left and right wings between stations Xors=417 and the outboard edge of the lower cap splice of the wing rear spar at station Xors=400; temporary and permanent repairs if necessary; and repetitive inspections of repaired areas, and corrective actions if necessary. We are issuing this AD to correct the unsafe condition on these products.
AD 2011-24-05 · published Nov 29, 2011, effective Jan 3, 2012
Airbus Airplanes
We are superseding an existing airworthiness directive (AD) that applies to certain Airbus Model A330-201, -202, -203, -223, -243, -301, -302, -303, -321, -322, -323, -341, -342, and -343 airplanes; and Model A340-200 and -300 series airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-24-06 · published Nov 29, 2011, effective Jan 3, 2012
BAE SYSTEMS (Operations) Limited Airplanes
We are superseding an existing airworthiness directive (AD) that applies to all BAE SYSTEMS (Operations) Limited Model BAe 146- 100A, -200A, and -300A airplanes; and Model Avro 146-RJ70A, 146-RJ85A, and 146-RJ100A airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: * * * * *
AD 2011-24-09 · published Nov 29, 2011, effective Dec 14, 2011
Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A340-200 and -300 series airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-20-08 · published Nov 4, 2011, effective Nov 21, 2011
Agusta S.p.A. (Agusta) Model AB139 and AW139 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Agusta model helicopters. This action requires inspecting certain modules and related connectors for corrosion. If there is corrosion on the connectors, this AD requires cleaning the connectors before further flight. If there is corrosion on a module, before further flight, this AD requires replacing the module with an airworthy module. This AD also requires modifying the Number 2 Modular Avionic Unit (MAU) ventilation duct. This amendment is prompted by some in- flight emergencies due to internal corrosion of the MAU circuit card assemblies. The actions specified in this AD are intended to detect corrosion of certain modules to prevent the display of misleading data to the flight crew, disengagement of the flight director modes of the autopilot or other alert system, increased workload of the flight crew, and subsequent loss of control of the helicopter.
AD 2011-21-13 · published Nov 4, 2011, effective Nov 21, 2011
Eurocopter Deutschland GmbH (ECD) Model MBB-BK 117 C-2 Helicopters
This amendment adopts a new airworthiness directive (AD) for ECD Model MBB-BK 117 C-2 helicopters. This action requires revising the Rotorcraft Flight Manual (RFM) by inserting certain temporary pages into the Emergency and Performance Data sections of the RFM to alert the operators to monitor the power display when a generator is deactivated and provides appropriate actions. This amendment is prompted by reports of too high a current flow when one generator is deactivated. The actions specified in this AD are intended to prevent failure of the remaining generator when one generator is deactivated, loss of electrical power, loss of systems necessary for flight safety, and subsequent loss of control of the helicopter.
AD 2011-23-02 · published Nov 4, 2011, effective Nov 21, 2011
Bell Helicopter Textron, Inc. (Bell), Model 205A-1, 205B, 210, and 212 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for Bell Model 205B and 212 helicopters with certain main rotor blade (blade) assemblies installed. That AD currently requires washing the upper and lower surfaces of each blade and visually inspecting the grip plates, doublers, and the remaining upper and lower surfaces of the blades in the area between blade stations 24.5 to 40 for an edge void, corrosion, or a crack. This amendment retains the requirements of that AD for the affected part-numbered blades but increases the scope and frequency of the inspections and expands the applicability to include the Model 205A-1 and 210 helicopters, additional blade part numbers, and all helicopter serial numbers for the affected helicopter models. This amendment also requires applying a light coat of preservative oil (C-125) to all surfaces of the blade in addition to the inspection areas as required in the existing AD. This amendment is prompted by an additional report of a fatigue crack on a blade installed on a Model 212 helicopter. The actions specified by this AD are intended to detect an edge void, corrosion, or a crack on a blade, and to prevent loss of a blade and subsequent loss of control of the helicopter.
AD 2011-22-08 · published Nov 8, 2011, effective Dec 13, 2011
MD Helicopters, Inc. Model MD900 Helicopters
This amendment supersedes an existing airworthiness directive (AD) that applies to MD Helicopters, Inc. (MDHI) Model MD900 helicopters. That AD currently requires turning ON both Vertical Stabilizer Control System (VSCS) switches and turning OFF the autopilot (AP/SAS) switch; pulling certain AP/SAS circuit breakers; installing a placard near the AP/SAS master switch; installing an airspeed limitation placard on the instrument panel; and making changes to the Rotorcraft Flight Manual (RFM). This amendment retains those requirements and provides an option of replacing each affected tube adapter with a newly-designed tube adapter, which provides terminating action for the unsafe condition. This amendment is prompted by the manufacturer introducing an improved, newly-designed tube adapter. The actions specified by this AD are intended to prevent loss of yaw control and subsequent loss of control of the helicopter.
AD 2011-22-05 · published Nov 10, 2011, effective Nov 25, 2011
Eurocopter France Model AS350B, B1, B2, B3, BA, C, D, and D1; and AS355E, F, F1, F2, N, and NP Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the Eurocopter France (Eurocopter) Model AS350B, B1, B2, B3, BA, C, D, and D1 helicopters; and Model AS355E, F, F1, F2, and N helicopters with certain tail rotor pitch control rods installed. That AD requires a daily check of the tail rotor (T/R) pitch control rod (control rod) outboard spherical bearing (bearing) for play. If play exists, that AD requires measuring the bearing's radial and axial play. Since that AD was issued, an incident occurred where the pilot of a Model AS350 helicopter felt vibrations in the anti-torque pedal in flight, resulting in a precautionary landing. An investigation determined that the control rod showed extensive wear on the ball- joint. This superseding AD maintains the requirements of the existing AD, and expands the applicability to include the Model AS355NP helicopter and additional part-numbered control rods. The actions specified by this AD are intended to prevent failure of a control rod, loss of T/R control, and subsequent loss of control of the helicopter.
AD 2011-21-17 · published Nov 2, 2011, effective Nov 17, 2011
General Electric Company Turboshaft Engines
We are adopting a new airworthiness directive (AD) for all General Electric Company (GE) CT7-8A, CT7-8A1, CT7-8E, and CT7-8F5 turboshaft engines with a fuel filter differential pressure switch, part number (P/N) TD028VF0H7Y5 (part of the fuel filter assembly, P/N 4110T53P06) installed. This AD requires daily visual inspections of the fuel filter differential pressure switch for fuel leaks and for excessive cracking of the switch mounting flanges due to stress- corrosion. This AD also requires the installation of a collar kit over the fuel filter differential pressure switch as terminating action to the daily inspections. This AD was prompted by reports of 47 fuel filter differential pressure switches found with stress-corrosion cracking of the mounting flanges. We are issuing this AD to prevent unrecoverable in-flight engine shutdown, engine bay fire due to fuel leakage, and forced landing or accident.
AD 2011-22-03 · published Nov 2, 2011, effective Nov 17, 2011
Rolls-Royce Corporation Turbofan Engines
We are adopting a new airworthiness directive (AD) for Rolls- Royce Corporation (RRC) AE 3007A, AE 3007A1/1, AE 3007A1, AE 3007A1/3, AE 3007A1E, AE 3007A1P, and AE 3007A3 turbofan engines. This AD requires initial and repetitive eddy current inspections (ECI) of certain 6th-through-13th stage compressor wheel knife edge seals, and initial and repetitive ECIs of the compressor wheel outer circumference, for cracks. This AD was prompted by reports of low-cycle fatigue cracks found during shop visits, in the 6th-through-13th stage compressor wheels having chrome-carbide coated or uncoated knife edge seals. We are issuing this AD to prevent uncontained failure of the 6th-through-13th stage compressor wheel, leading to damage to the airplane.
AD 2011-23-01 · published Nov 7, 2011, effective Nov 22, 2011
Thielert Aircraft Engines GmbH (TAE) Reciprocating Engines
We are superseding an existing airworthiness directive (AD) for Thielert Aircraft Engines GmbH (TAE) Models TAE 125-01 and TAE 125- 02-99 reciprocating engines. That AD currently requires replacement of certain part numbers (P/Ns) and serial numbers (S/Ns) of clutch assemblies due to clutch failure. The failures identified above could lead to engine in-flight shutdown and loss of control of the airplane. This AD requires the same actions, but applies the corrective action to an additional 244 affected clutch assemblies. This AD was prompted by TAE identifying additional clutch assemblies with nonconforming disc springs. We are issuing this AD to correct the unsafe condition on these products.
AD 2011-23-04 · published Nov 7, 2011, effective Dec 12, 2011
General Electric Company (GE) CF6 Turbofan Engines
We are superseding an existing airworthiness directive (AD) for the engines identified above. That AD currently requires initial and repetitive visual inspections of the forward engine mount assembly side links for cracks, stripping and reapplying the Sermetel W coating on the side links at every exposure of the side link. This new AD requires those same inspections, stripping and reapplying the Sermetel W coating, and adds two part numbers to the applicability. This AD was prompted by a review of the inspection program, which revealed that GE had omitted two affected side link part numbers from the applicability. We are issuing this AD to prevent failure of the side links and possible engine separation from the airplane.
AD 2011-23-12 · published Nov 14, 2011, effective Nov 29, 2011
Rolls-Royce plc RB211-524G2-19; -524G2-T-19; -524G3-19; -524G3-T-19; 524H2-19; -524H2-T-19; -524H-36; and -524H-T-36 Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-23-13 · published Nov 14, 2011, effective Nov 29, 2011
Honeywell International Inc. Turboshaft Engines
We are adopting a new airworthiness directive (AD) for Honeywell International Inc. LTS101-600A-2, -3, -3A, and LTS101-700D-2 turboshaft engines with certain power turbine governors (PTG) model AL- AB1, installed, that are marked with compliance symbol N or P, or with no compliance symbol, on the PTG identification plate. This AD requires initial and repetitive replacements of the affected PTGs. This AD was prompted by reports of two accidents where the engines suddenly lost power and the helicopters had to make emergency autorotation landings, leading to substantial damage to the helicopters. We are issuing this AD to prevent loss of engine power, leading to emergency autorotation landing and damage to the helicopter.
AD 2011-24-08 · published Nov 22, 2011, effective Dec 7, 2011
Turbomeca S.A. Makila 1A2 Turboshaft Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-24-07 · published Nov 29, 2011, effective Dec 14, 2011
Turbomeca S.A. Arriel 2B Turboshaft Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2011-24-11 · published Nov 29, 2011, effective Dec 14, 2011
Honeywell International Inc. Turbofan Engines
We are adopting a new airworthiness directive (AD) for certain Honeywell International Inc. ALF502L-2C, ALF502R-3, ALF502R-3A, ALF502R-5, LF507-1F, and LF507-IH turbofan engines. This AD requires removing from service certain second stage high pressure compressor (HPC2) discs. This AD was prompted by a report of cracks found in an HPC2 disc during routine inspection. We are issuing this AD to prevent the affected discs from fracturing before reaching the currently published life limit. A disc fracture could result in an uncontained failure of the disc and damage to the airplane.
