40 Airworthiness Directives: 34 airplane, 4 rotorcraft, 2 engine.
AD 2008-03-05 · published Feb 5, 2008, effective Mar 11, 2008
Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP Series Airplanes; and Model 767-200 and -300 Series Airplanes; Equipped With Certain Goodrich Evacuation Systems
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747- 200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes; and Model 767-200 and -300 series airplanes; equipped with certain Goodrich evacuation systems. For certain airplanes, this AD requires replacing the evacuation system shear-pin restraints with new ones. For certain other airplanes, this AD requires an inspection for manufacturing lot numbers; and a general visual inspection of the shear-pin restraints for discrepancies, and corrective actions if necessary. This AD results from several reports of corroded shear-pin restraints that prevented Goodrich evacuation systems from deploying properly. We are issuing this AD to prevent failure of an evacuation system, which could impede an emergency evacuation and increase the chance of injury to passengers and flightcrew during the evacuation.
AD 2008-03-08 · published Feb 5, 2008, effective Mar 11, 2008
Saab Model SAAB 2000 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-03-10 · published Feb 5, 2008, effective Mar 11, 2008
Cessna Aircraft Company Models 525, 525A, and 525B Airplanes
We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 525, 525A, and 525B airplanes. This AD requires you to inspect the lower wing skin structure, forward wing spar, lower fuselage skin, fairings, and the external fairing frames for corrosion; repair any damage found; apply a corrosion inhibitive sealant to the fuselage fairings before reinstalling; and disable the cockpit mounted pilot relief tube. This AD results from leaking of the cockpit mounted pilot relief tube, which caused corrosion of the airplane structure. We are issuing this AD to detect and correct any damage from corrosion of the airplane structure. Corrosion of the airplane structure could cause structural degradation and lead to structural failure of the airplane with consequent loss of control.
AD 2008-03-11 · published Feb 5, 2008, effective Mar 11, 2008
Alpha Aviation Design Limited Model R2160 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as distortion of the rudder bars due to rudder control forces during aerobatic operation and nose wheel steering reaction forces. Rudder bar distortion could result in reduced control or loss of control. This AD requires actions that are intended to address the unsafe condition described in the MCAI.
AD 2008-03-12 · published Feb 5, 2008, effective Mar 11, 2008
McDonnell Douglas Model DC-8-11, DC-8-12, DC-8-21, DC-8-31, DC-8-32, DC-8-33, DC-8-41, DC-8-42, and DC-8-43 Airplanes; Model DC-8F-54 and DC-8F-55 Airplanes; Model DC-8-50, -60, -60F, -70, and -70F Series Airplanes; Model DC-9-10, -20, -30, -40, and -50 Series Airplanes; Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), and DC-9-87 (MD-87) Airplanes; and Model MD-8
The FAA is superseding an existing airworthiness directive (AD), which applies to certain McDonnell Douglas airplanes. The existing AD currently requires an initial general visual or dye penetrant inspection, repetitive dye penetrant inspections, and replacement, as necessary, of the rudder pedal bracket. The existing AD also currently requires, for certain airplanes, replacing the rudder pedal bracket assemblies with new, improved parts, which would terminate the repetitive inspections. For certain airplanes, this new AD requires initial inspection at a reduced threshold, removes an inspection option, and lengthens the repetitive inspection intervals. This AD results from reports of failures of the captain's rudder pedal brackets before reaching the initial inspection threshold identified in the existing AD. We are issuing this AD to prevent failure of the rudder pedal bracket assembly, which could result in the loss of rudder and braking control at either the captain's or first officer's position.
AD 2008-03-13 · published Feb 5, 2008, effective Feb 20, 2008
ATR Model ATR42-500 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain ATR Model ATR42-500 series airplanes. This AD requires removing metallized polyethylene terephtalate (MPET) insulation blankets installed on the left and the right sides of the airplane over frame 24 between stringers 5 and 14. This AD results from reports indicating that burnt spots were found on the MPET insulation blankets installed over frame 24. The actions specified by this AD are intended to ensure that MPET insulation blankets are removed over frame 24. Such MPET insulation blankets, if not removed, could propagate a small fire that is the result of an electrical arc and could lead to a much larger fire.
AD 2008-03-14 · published Feb 5, 2008, effective Mar 11, 2008
Piaggio Aero Industries S.p.A. Model P 180 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-03-15 · published Feb 5, 2008, effective Mar 11, 2008
EADS SOCATA Model TBM 700 Airplanes
We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-03-16 · published Feb 5, 2008, effective Mar 11, 2008
Cirrus Design Corporation Models SR20 and SR22 Airplanes
We are adopting a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. This AD requires you to inspect the rudder, aileron, and rudder-aileron interconnect rigging; correct any out-of-rig condition; replace the attaching hardware for the rudder-aileron interconnect arm; and report any out-of-rig condition found. This AD results from a jamming of the aileron and rudder controls on a Model SR20 airplane, which resulted in loss of rudder and aileron flight controls. We are issuing this AD to prevent the possibility of jamming of the rudder-aileron interconnect system, which may result in loss of rudder and aileron flight controls.
AD 2008-03-17 · published Feb 11, 2008, effective Mar 17, 2008
Saab Model SAAB SF340A and SAAB 340B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-03-18 · published Feb 11, 2008, effective Mar 17, 2008
Saab Model SAAB SF340A and Model SAAB 340B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-03-19 · published Feb 11, 2008, effective Mar 17, 2008
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-03-20 · published Feb 11, 2008, effective Mar 17, 2008
Boeing Model 737-300, -400, and -500 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-300, -400, and -500 series airplanes. This AD requires, among other actions, modifying the door-mounted escape system of the forward right side door slide compartment. This AD results from reports indicating that the forward right escape slide inflated 90 degrees out of alignment after deployment from the forward right side slide compartment. We are issuing this AD to prevent the escape slide from being unusable during an emergency evacuation and consequent injury to passengers or crewmembers.
AD 2008-03-21 · published Feb 11, 2008, effective Feb 26, 2008
Fokker Model F.27 Mark 050 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-01 · published Feb 13, 2008, effective Mar 19, 2008
Airbus Model A300, A310, and A300-600 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-02 · published Feb 13, 2008, effective Feb 13, 2008
Bombardier Model DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires inspecting all barrel nuts to determine if the barrel nuts have a certain marking, inspecting affected bolts to determine if the bolts are pre-loaded correctly, and replacing all hardware if the pre-load is incorrect. For airplanes on which the pre-load is correct, this AD requires doing repetitive visual inspections for cracking of the barrel nuts and cradles and replacing all hardware for all cracked barrel nuts. This AD also requires replacement of all hardware for certain affected barrel nuts that do not have cracking, which would end the repetitive inspections for those airplanes. This AD also provides an optional replacement for all affected barrel nuts. This AD results from reports of cracking in the barrel nuts at the four primary front spar wing-to-fuselage attachment joints. We are issuing this AD to detect and correct cracking of the barrel nuts at the wing front spar wing-to- fuselage joints, which could result in reduced structural integrity of the wing-to-fuselage attachments and consequent detachment of the wing.
AD 2008-01-02 · published Feb 14, 2008, effective Jan 23, 2008
Viking Air Limited Model (Caribou) DHC-4 and (Caribou) DHC-4A Airplanes; and Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP Series Airplanes
The FAA is correcting typographical errors in three existing airworthiness directives (ADs) that were published in the Federal Register on January 8, 2008 (73 FR 1269); January 7, 2008 (73 FR 1052); and January 7, 2008 (73 FR 1055). The errors resulted in incorrect docket numbers. One AD applies to all Viking Air Limited Model (Caribou) DHC-4 and (Caribou) DHC-4A airplanes. The other two ADs apply to all Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747- 200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. The Viking Air AD requires doing a fluorescent penetrant inspection for cracking of certain upper engine mount bracket assemblies, and corrective actions if necessary. One of the Boeing ADs requires revising the FAA-approved maintenance inspection program to include inspections that will give no less than the required damage tolerance rating for each structural significant item, and repair of cracked structure. The other Boeing AD requires implementing a corrosion prevention and control program.
AD 2008-04-04 · published Feb 14, 2008, effective Mar 20, 2008
Bombardier Model DHC-8-400 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-06 · published Feb 22, 2008, effective Mar 28, 2008
Boeing Model 707 Airplanes and Model 720 and 720B Series Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 707 airplanes and Model 720 and 720B series airplanes. This AD requires repetitive inspections for any cracking of or damage to the left side and right side flight deck No. 2, No. 4, and No. 5 windows, as necessary, and corrective actions if necessary. This AD results from reports of in-flight departure and separation of the flight deck windows. We are issuing this AD to detect and correct cracking in the vinyl interlayer or damage to the structural inner glass panes of the flight deck No. 2, No. 4, and No. 5 windows, which could result in loss of a window and rapid loss of cabin pressure. Loss of cabin pressure could cause crew communication difficulties or crew incapacitation.
AD 2008-04-07 · published Feb 22, 2008, effective Mar 28, 2008
Saab Model SAAB SF340A and SAAB 340B Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-08 · published Feb 22, 2008, effective Mar 28, 2008
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-09 · published Feb 22, 2008, effective Mar 28, 2008
Taylorcraft A, B, and F Series Airplanes
We are adopting a new airworthiness directive (AD) to supersede AD 2007-16-14, which applies to all Taylorcraft (Taylorcraft) A, B, and F series airplanes. AD 2007-16-14 currently requires you to do an initial visual inspection of the left and right wing front and aft lift struts for cracks and corrosion and replace any cracked strut or strut with corrosion that exceeds certain limits. If the strut is replaced with an original design vented strut, AD 2007-16-14 requires you to repetitively inspect those struts thereafter. Since we issued AD 2007-16-14, we determined that the eddy current inspection method does not address the unsafe condition for the long term. We also determined that Models FA-III and TG-6 airplanes are not equipped with the affected struts. Consequently, this AD retains the actions required in AD 2007-16-14, except it removes the eddy current inspection method (provides 24-month credit if already done using this method), adds the radiograph method as an inspection method, changes the Applicability section, and changes the compliance time between the repetitive inspections. We are issuing this AD to detect and correct cracks and corrosion in the left and right wing front and aft lift struts. This condition, if not corrected, could result in failure of the lift strut and lead to in-flight separation of the wing.
AD 2008-04-10 · published Feb 22, 2008, effective Mar 28, 2008
Boeing Model 727 Airplanes
We are adopting a new airworthiness directive (AD) for all Boeing Model 727 airplanes. This AD requires revising the FAA-approved maintenance program by incorporating new airworthiness limitations (AWLs) for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. This AD also requires the initial inspection of a certain repetitive AWL inspection to phase in that inspection, and repair if necessary. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
AD 2008-04-11 · published Feb 22, 2008, effective Mar 28, 2008
Boeing Model 707 Airplanes, and Model 720 and 720B Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 707 airplanes, and Model 720 and 720B series airplanes. This AD requires revising the FAA-approved maintenance program by incorporating new airworthiness limitations (AWLs) for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. This AD also requires the initial performance of certain repetitive AWL inspections to phase in those inspections, and repair if necessary. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2008-04-13 · published Feb 22, 2008, effective Mar 28, 2008
ATR Model ATR42 and ATR72 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-14 · published Feb 26, 2008, effective Apr 1, 2008
Dassault Model Falcon 2000, Falcon 2000EX, Mystere-Falcon 900, Falcon 900EX, Fan Jet Falcon, Mystere-Falcon 50, Mystere-Falcon 20, Mystere-Falcon 200, and Falcon 10 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Dassault Model Falcon 2000, Mystere-Falcon 900, Falcon 900EX, Fan Jet Falcon, Mystere-Falcon 50, Mystere-Falcon 20, Mystere-Falcon 200, and Falcon 10 series airplanes. That AD currently requires repetitive tests and inspections to detect discrepancies of the overwing emergency exit, and corrective action if necessary. This new AD expands the applicability of the existing AD and extends the repetitive test and inspection intervals for all airplanes. This AD results from reports of incorrect operation of the overwing emergency exit due to interference between the emergency exit and the interior accommodation. We are issuing this AD to prevent failure of the overwing emergency exits to open, and consequent injury to passengers or crewmembers during an emergency evacuation.
AD 2008-04-12 · published Feb 28, 2008, effective Apr 3, 2008
Boeing Model 767-200, -300, -300F, and -400ER Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 767-200, -300, and -300F series airplanes. That AD currently requires reworking the surface of the ground stud bracket of the left and right transformer rectifier units (TRUs) and the airplane structure mounting surface, and measuring the resistance from the bracket to the structure and the ground lugs to the bracket using a bonding meter. This new AD revises the applicability of the existing AD to include additional airplanes and requires, among other actions, installation of a new ground stud bracket using faying surface bonding. This AD results from a report of loss of all direct current (DC) power generation during a flight, due to inadequate electrical ground path between the ground bracket of the TRUs/main battery charger (MBC) and the structure. We are issuing this AD to prevent depletion of the main battery while in flight, resulting from the loss of both TRUs and the MBC, and consequent loss of all DC power, which could impact the safe flight and landing of the airplane due to the loss of function or malfunction of essential/critical systems and displays in the cockpit.
AD 2008-04-16 · published Feb 28, 2008, effective Apr 3, 2008
BAE Systems (Operations) Limited Model BAe 146 and Model Avro 146-RJ Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-17 · published Feb 28, 2008, effective Apr 3, 2008
Bombardier Model DHC-8-102, DHC-8-103, DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-315 Airplanes, and Model DHC-8-400 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-18 · published Feb 28, 2008, effective Apr 3, 2008
EMBRAER Model EMB-120, -120ER, -120FC, -120QC, and -120RT Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-19 · published Feb 28, 2008, effective Apr 3, 2008
ATR Model ATR42 and ATR72 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-20 · published Feb 28, 2008, effective Apr 3, 2008
Airbus Model A319, A320, and A321 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2008-04-21 · published Feb 28, 2008, effective Apr 3, 2008
Boeing Model 737-300, -400, and -500 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-300, -400, and -500 series airplanes. This AD requires repetitive inspections for cracking of the body buttock line (BBL) 0.07 floor beam between body station (BS) 651 and BS 676 and between BS 698 and BS 717, and related investigative and corrective actions if necessary. This AD also provides an optional terminating action for the repetitive inspections. This AD results from reports of cracking in the BBL 0.07 floor beam. We are issuing this AD to prevent failure of the main deck floor beams at certain body stations due to fatigue cracking, which could result in rapid decompression of the airplane.
AD 2008-04-22 · published Feb 28, 2008, effective Apr 3, 2008
Fokker Model F.28 Mark 0070 and 0100 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
AD 2007-26-51 · published Feb 1, 2008, effective Feb 19, 2008
Eurocopter Deutschland GmbH Model EC135 Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2007-26-51, which was sent previously to all known U.S. owners and operators of Eurocopter Deutschland GmbH (Eurocopter) Model EC135 helicopters by individual letters. This AD requires, within 5 hours time-in-service (TIS), inspecting the tail rotor control rod (control rod) and adjoining ball pivot and replacing any unairworthy parts before further flight. This amendment is prompted by a report of a fatal accident involving the failure of a control rod. The actions specified by this AD are intended to prevent failure of a control rod and subsequent loss of control of the helicopter.
AD 2008-03-07 · published Feb 5, 2008, effective Feb 20, 2008
Eurocopter Model AS 332 L2 Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Model AS 332 L2 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The European Aviation Safety Agency (EASA), the Technical Agent of France, with which we have a bilateral agreement, states in the MCAI:
AD 2008-04-03 · published Feb 20, 2008, effective Mar 6, 2008
Eurocopter France Model AS-365N2 and N3, SA-365C, C1 and C2, and SA-365N and N1 Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Model AS-365N2 and N3, SA-365C, C1 and C2, and SA-365N and N1 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The European Aviation Safety Agency (EASA), the Technical Agent for France, with which we have a bilateral agreement, states in the MCAI:
AD 2008-04-05 · published Feb 20, 2008, effective Mar 6, 2008
Eurocopter Deutschland Model EC135 Helicopters
We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland (Eurocopter) Model EC135 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The European Aviation Safety Agency (EASA), the Technical Agent for the Federal Republic of Germany, with which we have a bilateral agreement, states in the MCAI:
AD 2008-03-09 · published Feb 4, 2008, effective Mar 10, 2008
CFM International, S.A. CFM56-7B Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for CFM International, S.A. CFM56-7B series turbofan engines. This AD requires revising the Airworthiness Limitations Section (ALS) in the Engine Shop Manual (ESM) and the air carrier's approved continuous airworthiness maintenance program (CAMP) to add mandatory inspections of certain low pressure turbine rear frames (TRFs) to the ALS or CAMP. This AD results from a refined lifing analysis by the engine manufacturer that shows the need to identify an initial threshold for inspecting certain TRFs. We are issuing this AD to prevent failure of the TRF from low-cycle fatigue cracks. Failure of the TRF could result in engine separation from the airplane, which could lead to loss of control of the airplane.
AD 2008-05-01 · published Feb 28, 2008, effective Apr 3, 2008
General Electric Company CF34-8C1/-8C5/-8C5B1/-8E5/-8E5A1, and CF34-10E Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CF34-8C1/-8C5/-8C5B1/-8E5/-8E5A1, and CF34-10E series turbofan engines with certain part number (P/N) and serial number (SN) fuel metering units (FMU) installed. This AD requires a onetime test of the FMU for a miswired (reversed polarity) condition of the input wires to the overspeed solenoid. This AD results from the discovery of miswired FMU overspeed solenoids in the field. We are issuing this AD to prevent the engine from failing to shutdown during an overspeed which may lead to uncontained engine failure.
