37 Airworthiness Directives: 29 airplane, 2 rotorcraft, 6 engine.
AD 2005-15-16 · published Aug 1, 2005, effective Sep 6, 2005
AvCraft Dornier Model 328-300 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain AvCraft Dornier Model 328-300 airplanes. This AD requires modifying the electrical wiring of the fuel pumps; installing insulation at the flow control and shut-off valves, and other components of the environmental control system; installing markings at fuel wiring harnesses; replacing the wiring harness of the auxiliary fuel system with a new wiring harness; and installing insulated couplings in the fuel system; as applicable. This AD also requires revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness to incorporate new inspections of the fuel tank system. This AD is prompted by the results of fuel system reviews conducted by the airplane manufacturer. We are issuing this AD to reduce the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2005-16-01 · published Aug 2, 2005, effective Sep 6, 2005
Boeing Model 747-200B, 747-300, 747-400, and 747-400D Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-200B, 747-300, 747-400, and 747-400D series airplanes. This AD requires modifying the lateral shear beam for the Door 5 crew rest and, for certain airplanes, replacing Zone E tie rods and modifying the Zone E stowbin ladder. This AD results from a report indicating that the lateral shear beam for the Door 5 crew rest does not meet the 9G forward loading requirement. We are issuing this AD to prevent the structural support for the Door 5 crew rest and Zone E stowbins from failing, which could result in the crew rest or stowbins falling during an emergency and consequent injury to crew and passengers.
AD 2005-16-02 · published Aug 2, 2005, effective Sep 6, 2005
Raytheon Model HS.125 Series 700A Airplanes, Model BAe.125 Series 800A Airplanes, and Model Hawker 800 and Hawker 800XP Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon Model HS.125 series 700A airplanes, Model BAe.125 series 800A airplanes, and Model Hawker 800 and Hawker 800XP airplanes. This AD requires inspecting to determine the current rating of the circuit breakers of certain cockpit ventilation and avionics cooling system blowers; and replacing the circuit breakers and modifying the blower wiring, as applicable. This AD results from a report indicating that a blower motor seized up and gave off smoke. We are issuing this AD to prevent smoke and fumes in the cockpit in the event that a blower motor seizes and overheats due to excessive current draw.
AD 2005-16-03 · published Aug 2, 2005, effective Sep 6, 2005
Bombardier Model DHC-7-100, DHC-7-101, DHC-7-102, and DHC-7-103 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-7-100, DHC-7-101, DHC-7-102, and DHC-7-103 airplanes. This AD requires revising the Airworthiness Limitations section of the Instructions of Continued Airworthiness to include a new, lower life limit for lower wing skins. This AD results from the discovery that, during the manufacture of the lower wing skins, score marks may have been accidentally inscribed around the edge of the lower wing skin doublers. We are issuing this AD to prevent fatigue cracks from developing at the score marks in the lower wing skins, which could result in the structural failure of the wing.
AD 2005-16-06 · published Aug 9, 2005, effective Sep 13, 2005
Boeing Model 747 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747 airplanes. This AD requires modifying the inflation systems of the upper deck escape slides; single-piece off- wing escape ramps/slides; two-piece off-wing escape slides; and door 1, 2, 4, and 5 escape slides/rafts. This AD results from a report of 30- to 60-second delays in the inflation of escape slides/rafts. We are issuing this AD to prevent actuation delays in the inflation systems of the escape slides/rafts, which could result in delayed or failed deployment of escape slides/rafts during emergency evacuation of an airplane.
AD 2005-16-07 · published Aug 9, 2005, effective Sep 13, 2005
Boeing Model 727 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 727 airplanes. This AD requires determining whether any float switches are installed in the fuel tanks, and corrective actions if necessary. This AD results from reports of contamination of the fueling float switch by moisture or fuel, and chafing of the float switch wiring against the fuel tank conduit. We are issuing this AD to prevent such contamination and chafing, which could present an ignition source inside the fuel tank that could cause a fire or explosion.
AD 2005-16-08 · published Aug 9, 2005, effective Sep 13, 2005
McDonnell Douglas Model 717-200 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model 717-200 airplanes. This AD requires repetitively replacing and testing a certain relay in the passenger oxygen release system in the forward cabin. This AD results from reports of a failed relay in the passenger oxygen release system. We are issuing this AD to prevent failure of the relay, which could result in the oxygen masks failing to deploy and deliver oxygen to the passengers in the event of a rapid decompression or cabin depressurization.
AD 2005-16-09 · published Aug 9, 2005, effective Sep 13, 2005
Learjet Model 23, 24, 25, 35, and 36 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Learjet Model 23, 24, 25, 35, and 36 airplanes. That AD currently requires repetitive inspections to detect deterioration of both flappers of the tip tank in each wing of the airplane, and various follow-on actions. The existing AD also requires replacing the flappers with new flappers, and repetitively performing certain other follow-on actions. This new AD requires an inspection of the flappers and flapper assemblies of the tip tank in each wing or a review of the airplane maintenance records to determine the part numbers, and replacement of certain flappers or flapper assemblies if necessary, which ends the existing repetitive inspections. This AD results from numerous continual inspections and the approval of a new, improved flapper and flapper assembly. We are issuing this AD to prevent significant reduction in the lateral control of the airplane due to imbalance of the fuel loads in the wings of the airplane.
AD 2005-16-10 · published Aug 9, 2005, effective Sep 13, 2005
Boeing Model 747-400 and 747-400D Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-400 and 747-400D series airplanes. This AD requires an inspection for corrosion and cracks of the station 980 upper deck floor beam, and repair and related investigative actions if necessary. This AD results from reports of corrosion under the cart lift threshold at the station 980 upper deck floor beam. We are issuing this AD to detect and correct such corrosion, which could result in a cracked or broken floor beam, extensive damage to adjacent structure, and possible rapid decompression of the airplane.
AD 2005-04-14 R1 · published Aug 11, 2005, effective Mar 15, 2005
Boeing Model 757-200, 757-200CB, and 757-200PF Series Airplanes Equipped With Rolls Royce Model RB211 Engines
The FAA is revising an existing airworthiness directive (AD), which applies to certain Boeing Model 757-200, 757-200CB, and 757-200PF series airplanes. That AD currently requires repetitive inspections to detect horizontal or vertical movement of the shims at the joint of the mid-bulkhead and the upper link fittings; repetitive inspections for cracking of the mid-bulkhead; and corrective action if necessary. That AD also provides optional terminating action for the repetitive inspections. This AD continues to require the existing requirements and optional actions and clarifies certain terminating actions. This AD results from comments received in response to an existing AD, requesting clarification. We are issuing this AD to detect and correct migration of shims at the joint of the mid-bulkhead and the upper link fittings and cracking of the mid-bulkhead, which could result in cracking of the strut and consequent loss of the strut and engine.
AD 2005-16-11 · published Aug 12, 2005, effective Sep 16, 2005
Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747SP, and 747SR Series Airplanes; Equipped With Pratt & Whitney Model JT9D-3 and -7 Series Engines
The FAA is adopting a new airworthiness directive (AD) for certain Boeing transport category airplanes listed above. This AD requires repetitive inspections for cracks of the upper surface of the aft lower spar web of the inboard and outboard struts, as applicable; and repetitive inspections for cracks of the upper surface of the intermediate web bay of the aft lower spar. This AD also requires repetitive inspections and torque checks of the bolts common to the aft lower spar chords and the fitting of the rear engine mount bulkhead for missing, loose, or fractured bolts, as applicable; and corrective action, if necessary. This AD is prompted by reports of cracking in the aft lower spar web and reports of missing and fractured bolts. We are issuing this AD to detect and correct cracking of the aft lower spar web, and to prevent missing, loose, or fractured bolts common to the aft lower spar chords and the fitting of the rear engine mount bulkhead, which could result in the loss of the aft lower spar load path and reduced structural capability of the pylon, which may result in the separation of the engine from the airplane.
AD 2005-16-13 · published Aug 15, 2005, effective Aug 30, 2005
Gulfstream Aerospace LP Model Galaxy and Gulfstream 200 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace LP Model Galaxy and Gulfstream 200 airplanes. This AD requires a one-time general visual inspection for any damaged wiring, splice, connector, and pins for the fuel standby feed pumps and replacement of any damaged wiring, splice, connector, or pin. This AD also requires replacement of the power and ground wires for the fuel standby feed pumps. This AD results from reports of evidence of overheating found on the feeder wires of the left and right fuel standby feed pumps. We are issuing this AD to detect and correct damaged wiring for the fuel standby feed pumps, which could result in an ignition source in an area where fuel vapor may be present, and a consequent fire or explosion.
AD 2005-16-14 · published Aug 15, 2005, effective Aug 30, 2005
Gulfstream Model G-IV, GIV-X, GV, and GV-SP Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Gulfstream Model G-IV and GV series airplanes, and certain GIV-X and GV-SP series airplanes. This AD requires a one-time inspection to determine if a certain floor heater pad system is installed, and deactivation of the subject floor heater pad system if it is installed. This AD results from an incident of short-circuiting of the floor heater pads, in which no circuit breakers tripped in response to the short-circuiting. We are issuing this AD to prevent short-circuiting of the floor heater pad system, which could result in a fire in the airplane cabin.
AD 2005-17-01 · published Aug 15, 2005, effective Sep 29, 2005
Pilatus Aircraft Ltd. Models PC-6, PC-6-H1, PC-6-H2, PC-6/350, PC-6/350-H1, PC-6/350-H2, PC-6/A, PC-6/A-H1, PC-6/A-H2, PC-6/B-H2, PC-6/B1-H2, PC-6/B2-H2, PC-6/B2-H4, PC-6/C-H2, and PC-6/C1-H2 Airplanes
The FAA adopts a new airworthiness directive (AD) for all Pilatus Aircraft Ltd. (Pilatus) (also identified as Fairchild Republic Company and Fairchild Heli Porter) Model PC-6 airplanes. This AD requires you to repetitively inspect the stabilizer-trim attachment and structural components for cracks, corrosion, and discrepancies and replace any defective part with a new part. This AD also requires you to replace all Fairchild connecting pieces, part number (P/N) 6232.0026.XX, with a Pilatus connecting piece and requires you to replace fittings without an index after the P/N with an improved part. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. We are issuing this AD to detect and correct defective stabilizer-trim attachments and surrounding structural components, which could result in failure of the stabilizer-trim attachment. This failure could lead to loss of control of the airplane.
AD 2005-13-35 · published Aug 22, 2005, effective Sep 26, 2005
Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 series airplanes. That AD currently requires installation of a placard on the instrument panel of the cockpit to advise the flightcrew that positioning of the power levers below the flight idle stop during flight is prohibited. Additionally, the existing AD requires eventual installation of an FAA-approved system that would prevent such positioning of the power levers during flight. Installation of that system terminates the requirement for installation of a placard. This new AD requires operators who have incorporated a certain Bombardier service bulletin to perform repetitive operational checks of the beta lockout system and to revise the Airworthiness Limitations document. This AD is prompted by in-service issues reported by operators who incorporated Bombardier Service Bulletin 8-76-24 as an alternative method of compliance to the existing AD. We are issuing this AD to prevent the inadvertent activation of ground beta mode during flight, which could lead to engine overspeed, engine damage or failure, and consequent reduced controllability of the airplane.
AD 2005-17-02 · published Aug 22, 2005, effective Sep 26, 2005
Boeing Model 777-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 777-200 and -300 series airplanes. This AD requires inspecting the valve control and indication wire bundles of the fuel system of the wing rear spar for discrepancies, and corrective action if necessary. This AD is prompted by reports of six incidents of the wire bundles chafing against the rear spar stiffeners outside the fuel tank. We are issuing this AD to prevent this chafing, which could result in wire damage leading to a short circuit, subsequent ignition of flammable vapors, and possible uncontrollable fire during fueling or flight.
AD 2005-17-03 · published Aug 22, 2005, effective Sep 26, 2005
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires installing additional shielding of the hydraulic lines in the wing box area. This AD results from the determination that the additional hydraulic line shields will protect the lines from possible impact by tire debris if the tire tread fails. We are issuing this AD to prevent damage to the hydraulic lines and subsequent leakage from the two hydraulic systems, which could result in loss of braking capability on the affected side of the airplane, asymmetrical braking, and reduced directional control--particularly during a rejected takeoff.
AD 2005-17-04 · published Aug 22, 2005, effective Sep 26, 2005
McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, MD-10-10F, and MD-10-30F Airplanes; and Model MD-11 and MD-11F Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas airplanes. This AD requires a general visual inspection for damage to the Firex discharge pipes and wye assembly of the fire extinguishing system of the number 2 engine; and corrective and other specified actions, as applicable. This AD results from reports of freezing damage to the Firex discharge pipes and wye assembly of the number 2 engine, and one report of a level 1 ENG FIRE AGENT LO alert during flight. We are issuing this AD to prevent accumulation of water in the discharge pipes and possible consequent freezing damage to the discharge pipes and wye assembly, which could lead to failure of the fire extinguishing system during a fire in the number 2 engine.
AD 95-19-15 R1 · published Aug 22, 2005, effective Oct 3, 2005
Tiger Aircraft LLC Models AA-5, AA-5A, AA-5B, and AG-5B Airplanes
The FAA is revising Airworthiness Directive (AD) 95-19-15 for all Tiger Aircraft LLC (Type Certificate A16EA formerly held by American General Aircraft Corporation and Grumman American Aviation Corporation) Models AA-5, AA-5A, AA-5B, and AG-5B airplanes. AD 95-19- 15 currently requires you to inspect the wing attach shoulder bolts for fretting, scoring, wear, or enlarged or elongated mounting holes (known as damage from hereon); replace any damaged parts; repair any damaged areas; inspect the wing spar at the center spar clearance gap for excessive clearance; and shim the spar if excessive clearance is found. That AD was written to apply to all serial numbers of all models. A design change was made in this area beginning with serial number 10175 of the Model AG-5B airplanes. Therefore, the action should not apply to Model AG-5B airplanes with a serial number of 10175 or higher. This AD retains all the actions of AD 95-19-15 for all airplanes originally affected, but cuts off the applicability for the Model AG-5B airplanes at serial number 10174. We are issuing this AD to continue to prevent wing attach shoulder bolt failure, which, if not detected and corrected, could lead to structural damage of the wing/fuselage to the point of failure.
AD 2005-13-09 · published Aug 23, 2005, effective Jul 26, 2005
GROB-WERKE Model G120A Airplanes
This document incorporates corrections to add service information to Airworthiness Directive (AD) 2005-13-09, which was published in the Federal Register on June 22, 2005 (70 FR 35993). AD 2005-13-09 applies to certain GROB-WERKE Model G120A airplanes. This action adds GROB-WERKE Service Bulletin No. MSB1121-052/2, dated February 14, 2005, to paragraphs (e)(1), (e)(2), and (h) of AD 2005-13- 09. This service information was included in the notice of proposed rulemaking (NPRM) for this AD, but we inadvertently omitted it in the final rule request for comments. We are re-issuing the AD in its entirety to help eliminate any confusion that this AD may have created.
AD 2005-17-07 · published Aug 23, 2005, effective Sep 7, 2005
Airbus Model A320-111 Airplanes and Model A320-200 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A320-111 airplanes and Model A320-200 series airplanes. This AD requires doing a one-time general visual inspection of the axle nut on each main landing gear (MLG) wheel for the presence of locking bolts and associated hardware; doing any related investigative and corrective actions as applicable; and submitting an inspection report to the manufacturer. This AD results from a report that an axle nut had separated from an axle on a main landing gear (MLG) wheel, due to missing locking bolts. We are issuing this AD to detect and correct missing locking bolts on the axle nuts of the MLG wheels. Absence of the locking bolts could result in separation of a wheel(s) from the axle and consequent reduced controllability of the airplane during takeoff and landing, and possible injury to people on the ground.
AD 2005-17-08 · published Aug 23, 2005, effective Sep 27, 2005
Airbus Model A321 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A321 series airplanes. This AD requires repetitive measurements for correct control rod gap of the hold-open mechanism of all emergency doors, and corrective actions if necessary. This AD also requires replacing the control rods with new, improved control rods, which would terminate the repetitive measurements. This AD results from a report that an operator found it impossible to lock emergency doors 2 and 3 in the open position. We are issuing this AD to prevent failure of the emergency doors to lock in the open position, which could interfere with passenger evacuation during an emergency.
AD 2005-17-09 · published Aug 23, 2005, effective Sep 27, 2005
Boeing Model 747, 757, 767 and 777 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 747, 757, 767, and 777 series airplanes. That AD currently requires modifying certain drip shields located on the flight deck, and follow-on actions. This new AD removes certain airplanes that are included in the applicability statement of the existing AD, and requires modifying additional drip shields on the flight deck of certain other airplanes. This AD is prompted by a determination that certain airplanes have drip shields that are not adequately resistant to fire. We are issuing this AD to prevent potential ignition of the moisture barrier cover of the drip shield, which could propagate a small fire that results from an electrical arc, leading to a larger fire.
AD 2005-17-10 · published Aug 23, 2005, effective Sep 27, 2005
Saab Model SAAB 2000 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Saab Model SAAB 2000 airplanes. This AD requires an inspection for cracking of the fastener holes in the front and rear spars, a modification of the fastener holes of the front and rear spars and the rear spar web, and related investigative/corrective actions if necessary. This AD is prompted by a report of cracking of certain fastener holes in the lower spar cap of the rear spar and in the lower skin at the front spar. We are issuing this AD to prevent cracking of the front and rear spars, which could result in fuel leakage and consequent reduced structural integrity of the wing structure.
AD 2005-17-11 · published Aug 23, 2005, effective Oct 7, 2005
The Cessna Aircraft Company Models 525, 525A, and 525B Airplanes
The FAA adopts a new airworthiness directive (AD) for certain The Cessna Aircraft Company (Cessna) Models 525, 525A, and 525B airplanes. This AD requires you to install identification sleeves on the wiring for both engine fire extinguisher bottles. This AD results from reports of incorrectly connecting wires to the engine fire extinguisher bottles. We are issuing this AD to prevent incorrect installation of the wires to the engine fire extinguisher bottles, which could result in failure of the engine fire extinguisher bottles to discharge when activated. This failure could lead to the inability to control an engine fire.
AD 2005-17-12 · published Aug 23, 2005, effective Sep 7, 2005
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires inspecting to identify the wing anti-ice ducts (piccolo tubes) in the wing leading edge. For airplanes with affected piccolo tubes, this AD requires revising the airplane flight manual (AFM) to introduce new procedures for operation in icing conditions. The optional implementation of repetitive inspections for cracks of affected piccolo tubes, and corrective actions if necessary, terminates the operational limitations. The optional installation of certain new piccolo tubes terminates both the AFM revision and the inspections. This AD was prompted by reports of failed piccolo tubes. We are issuing this AD to prevent cracked piccolo tubes, which could result in air leakage, a possible adverse effect on the anti-ice air distribution pattern and anti-ice capability without annunciation to the flight crew, and consequent reduced controllability of the airplane.
AD 2005-17-13 · published Aug 26, 2005, effective Sep 12, 2005
Short Brothers Model SD3-60 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Short Brothers Model SD3-60 airplanes. This AD requires an inspection of the rudder for damage, an inspection of the balance weight attachment for discrepancies, an inspection of the rudder horn spar and cleats for cracking and corrosion, and corrective action if necessary. This AD results from events in which fatigue cracking was found on the rudder horn spar. We are issuing this AD to detect and correct cracking and corrosion of the rudder horn spar, which could lead to detachment of the mass balance weight of the rudder. The detachment of the mass balance weight could jam or restrict the movement of the rudder, which could result in reduced controllability of the airplane. Loss of a mass balance weight could also damage other parts of the airplane, which could result in reduced controllability of the airplane, or could result in an injury to a person or damage to property on the ground.
AD 2005-17-14 · published Aug 26, 2005, effective Sep 30, 2005
Airbus Model A300 B2 and B4 Series Airplanes; Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model A300 C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes); and Model A310-200 and -300 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Airbus Model A300 B2 and B4 series airplanes; Model A300-600 series airplanes; and Model A310-200 and -300 series airplanes. That AD currently requires, among other actions, repetitive tests to detect desynchronization of the rudder servo actuators, and adjustment or replacement of the spring rods of the rudder servo actuators, if necessary. This new AD requires new repetitive tests/inspections/analyses of the rudder servo actuators, and related investigative/corrective actions if necessary. Accomplishment of the new actions ends the existing repetitive requirements. This AD is prompted by new reports of desynchronization of the rudder servo actuators. We are issuing this AD to prevent desynchronization of one of the three rudder servo actuators, which, if combined with an engine failure, could result in the loss of the related hydraulic system and could cause the loss of one of the two synchronized actuators. This condition could create additional fatigue loading and possible cracking on the attachment fittings and could result in the inability of the remaining synchronized actuator to maintain the commanded rudder deflection, which could result in reduced controllability of the airplane.
AD 2005-17-18 · published Aug 26, 2005, effective Sep 12, 2005
Airbus Model A330-200, A330-300, A340-200, and A340-300 Series Airplanes; and Model A340-541 and -642 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A330-200, A330-300, A340-200, and A340-300 series airplanes; and Model A340-541 and -642 airplanes. This AD requires repetitively resetting the display units (DUs) for the electronic instrument system (EIS) either by switching them off and back on again or by performing a complete electrical shutdown of the airplane. This AD results from an incident in which all of the DUs for the EIS went blank simultaneously during flight. We are issuing this AD to prevent automatic reset of the DUs for the EIS during flight and consequent loss of data from the DUs, which could reduce the ability of the flightcrew to control the airplane during adverse flight conditions.
AD 2005-16-04 · published Aug 8, 2005, effective Sep 12, 2005
Bell Helicopter Textron Model 206A and 206B Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron (Bell) Model 206A and 206B helicopters modified by Aeronautical Accessories, Inc. Supplemental Type Certificate (STC) SH1392SO with certain part-numbered high crosstubes. This amendment requires inspecting at specified time intervals and replacing any cracked crosstubes. This amendment is prompted by the discovery of a cracked high forward crosstube. The actions specified by this AD are intended to detect a crack in the crosstube which could lead to failure of the crosstube, collapse of the landing gear, and subsequent loss of control of the helicopter.
AD 2005-16-05 · published Aug 11, 2005, effective Aug 26, 2005
Robinson Helicopter Company Model R-22 Series Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Robinson Helicopter Company (Robinson) Model R-22 series helicopters that have been modified in accordance with Supplemental Type Certificate (STC) No. SR09189RC. This action requires inspecting the left-hand door and right-hand door for a crack in the door assembly integral frame, and replacing the door assembly if a crack is found. This AD also requires inspecting each door assembly to determine if the weather seal set is airworthy and installed properly, inspecting each door hinge for the proper installation of a cotter pin, and thereafter, at intervals not to exceed 100 hours time-in-service (TIS), inspecting each door assembly integral frame for a crack. This amendment is prompted by one accident and one incident involving Robinson Model R-22 series helicopters. The actions specified in this AD are intended to prevent separation of a door window or door assembly from the helicopter, which could damage the tail rotor during flight and result in loss of control of the helicopter.
AD 2005-16-12 · published Aug 11, 2005, effective Aug 26, 2005
Rolls-Royce Deutschland Ltd & Co KG (formerly Rolls-Royce Deutschland GmbH, formerly BMW Rolls-Royce GmbH) Model BR700-715A1-30, BR700-715B1-30, and BR700-715C1-30 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Rolls-Royce Deutschland Ltd & Co KG (RRD) (formerly Rolls-Royce Deutschland GmbH, formerly BMW Rolls-Royce GmbH) model BR700-715A1-30, BR700-715B1-30, and BR700-715C1-30 turbofan engines. This AD requires a onetime inspection of the Independent Overspeed Protection (IOP) unit, part number (P/N) 112E9321G2, for 19 specific serial numbers (SNs), and removal from service of those units. This AD results from a report that incorrect capacitors were installed in 19 IOP units. The incorrect capacitor in the IOP unit can lead to an inadvertent IOP command resulting in an in-flight engine shutdown. We are issuing this AD to prevent inadvertent dual-engine in-flight shutdown.
AD 2005-17-05 · published Aug 23, 2005, effective Sep 27, 2005
General Electric Company (GE) CF6-80C2 and CF6-80E1 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain GE CF6-80C2 and CF6-80E1 turbofan engines. This AD requires you to inspect the high pressure compressor rotor (HPCR) stage 11-14 spool shaft for circumferential repair cuts, and to repair or replace the spool shaft if you find certain circumferential cuts. This AD results from an updated stress analysis. We are issuing this AD to prevent failure of the HPCR stage 11-14 spool shaft due to low-cycle fatigue that could result in an uncontained engine failure.
AD 2005-17-06 · published Aug 23, 2005, effective Sep 27, 2005
Turbomeca Artouste III Series Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for Turbomeca Artouste III series turboshaft engines. This AD requires modification of the engine air intake assembly. This AD results from a report of an in-flight shutdown and subsequent loss of control of the helicopter due to ice ingestion into the engine. We are issuing this AD to prevent ice ingestion into the engine, which could lead to an in- flight shutdown and subsequent loss of control of the helicopter.
AD 2005-17-15 · published Aug 26, 2005, effective Sep 12, 2005
Turbomeca Arrius 2F Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for Turbomeca Arrius 2F turboshaft engines. This AD requires a one-time removal and inspection of the fuel filter-holder assembly to determine that the fuel control unit (FCU) filter is dimensionally correct. The AD also requires updating the Engine Maintenance Manuals to include a dimensional check of the fuel filter-holder assembly every time the FCU filter element is removed from the fuel filter-holder assembly. This AD results from reports of restricted fuel flow caused by a dimensionally incorrect FCU filter. Ground run testing may not detect the fuel flow limitation. We are issuing this AD to detect a dimensionally incorrect FCU filter that could lead to an undetected limitation of fuel flow, limiting the maximum power available in-flight, which could result in the inability to continue safe flight, avoid obstacles or land safely.
AD 2005-17-16 · published Aug 26, 2005, effective Sep 30, 2005
Pratt & Whitney JT8D-1, -1A, -1B, -7, -7A, -7B, -9, -9A, -11, -15, -15A, -17, -17A, -17R, -17AR, -209, -217, -217A, -217C, and -219 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-1, -1A, -1B, -7, -7A, -7B, -9, -9A, -11, -15, -15A, -17, -17A, -17R, -17AR, -209, -217, -217A, -217C, and -219 turbofan engines. This AD requires removing affected rotating parts overhauled by a certain repair vendor, and inspecting the parts as applicable. This AD results from reports that certain JT8D critical life-limited rotating parts have been returned to service with cracks, corrosion pitting, or dimensions outside of manual limits. We are issuing this AD to prevent failure of critical life-limited rotating engine parts which could result in an uncontained engine failure and damage to the airplane.
AD 2005-17-17 · published Aug 26, 2005, effective Sep 12, 2005
Turbomeca S.A. Arrius 2F Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for Turbomeca S.A. Arrius 2F turboshaft engines. This AD requires replacing certain O-rings on the check valve piston in the lubrication unit. This AD results from a report of a forced landing of a Eurocopter EC120B helicopter. We are issuing this AD to prevent an uncommanded in-flight shutdown of the engine, which could result in a forced autorotation landing and damage to the helicopter.
