62 Airworthiness Directives: 50 airplane, 5 rotorcraft, 4 engine, 1 propeller, 2 appliance.
AD 2005-11-07 · published Jun 7, 2005, effective Jul 18, 2005
Extra Flugzeugproduktions-und Vertriebs-GmbH Models EA-300, EA-300S, EA-300L, and EA-300/200 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Extra Flugzeugproduktions-und Vertriebs-GmbH (EXTRA) Models EA-300, EA- 300S, EA-300L, and EA-300/200 airplanes. This AD requires you to seal with firewall sealant the gaps between the bottom fuselage cover (belly fairing) and the firewall and repeat the sealing procedure whenever you install the bottom fuselage cover (belly fairing). This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to prevent fuel from flowing behind the firewall in the case of a fuel leak. This could result in an in-flight fire, which could cause loss of the airplane and crew.
AD 2005-11-08 · published Jun 7, 2005, effective Jul 18, 2005
GROB-WERKE Model G120A Airplanes
The FAA adopts a new airworthiness directive (AD) for all GROB-WERKE (GROB) Model G120A airplanes. This AD requires you to replace the main landing gear front and rear spherical bearings with improved spherical bearings. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to replace front and rear main landing gear bearings that are susceptible to damage when exposed to high axial loads, which could result in failure of the landing gear bearing. This failure could lead to loss of control on landing.
AD 2005-11-09 · published Jun 7, 2005, effective Jul 12, 2005
Boeing Model 727-200 Series Airplanes Equipped With a No. 3 Cargo Door
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 727-200 series airplanes equipped with a No. 3 cargo door. This AD requires repetitive detailed and high frequency eddy current inspections for cracking of the forward, lower corner frame and forward end of the lower beam of the No. 3 cargo door, and corrective actions if necessary. The AD provides an optional terminating action for the repetitive inspections. This AD is prompted by reports of cracking at the forward, lower corner frame and lower beam of the No. 3 cargo door. We are issuing this AD to detect and correct cracking of the forward, lower corner frame and forward end of the lower beam of the No. 3 cargo door, which could result in failure of the affected door stops, loss of the cargo door, and consequent rapid decompression of the airplane.
AD 2005-11-10 · published Jun 7, 2005, effective Jul 12, 2005
Bombardier Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-102, -103, -106, -201, -202, -301, -311 and -315 airplanes. This AD requires installation of check valves in Numbers 1 and 2 hydraulic systems, removal of the filters from the brake shuttle valves, and removal of the internal garter spring from the brake shuttle valves. This AD results from two instances of brake failure due to the loss of hydraulic fluid from both Numbers 1 and 2 hydraulic systems and one incident of brake failure due to filter blockage in the shuttle valve. We are issuing this AD to prevent the loss of hydraulic power from both hydraulic systems, which could lead to reduced controllability of the airplane, and to prevent brake failure, which could result in the loss of directional control on the ground and consequent departure from the runway during landing.
AD 2005-11-11 · published Jun 7, 2005, effective Jul 12, 2005
Bombardier Model DHC-8-400, -401, and -402 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400, -401, and -402 series airplanes. This AD requires repetitive inspections to detect discrepancies of the attachment fittings of the outboard flap front spar at flap track Number 4 and Number 5 locations, and corrective actions if necessary. This AD also requires eventual replacement of the attachment fittings as terminating action for the repetitive inspections. This AD is prompted by the discovery of several airplanes that have loose flap front spar attachment fittings at flap track Number 4 and Number 5 locations. We are issuing this AD to prevent the attachment fittings from becoming detached, and consequent loss of control of the airplane.
AD 2005-11-12 · published Jun 7, 2005, effective Jul 12, 2005
Boeing Model 767-200, -300, and -300F Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200, -300, and -300F series airplanes. This AD requires installing a new, improved foam seal around certain ducts in the forward cargo compartment. This AD is prompted by the detection of incorrectly installed smoke barrier seals around the electrical/ electronic equipment air supply and exhaust ducts. We are issuing this AD to prevent fire extinguishing agent from leaking out of the seals around the ducts in the forward cargo compartment in the event of an in-flight fire, which could result in failure to extinguish the fire and consequent smoke or fire extinguishing agent entering a compartment occupied by passengers or crew.
AD 2005-11-13 · published Jun 7, 2005, effective Jul 12, 2005
BAE Systems (Operations) Limited Model BAe 146 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain BAE Systems (Operations) Limited Model BAe 146 airplanes. This AD requires repetitive inspections for cracks of the fuselage pressure skin above the left and right main landing gear (MLG) bay. This AD also requires corrective action, including related investigative actions, if leaks are found. This AD is prompted by reports of cracks in the fuselage pressure skin above the left and right MLG bay. We are issuing this AD to detect and correct fatigue cracking in the fuselage pressure skin above the left and right MLG bay; such fatigue cracking could adversely affect the structural integrity of the fuselage and its ability to maintain pressure differential.
AD 2005-11-06 · published Jun 8, 2005, effective Jul 18, 2005
Pilatus Aircraft Ltd. Models PC-12 and PC-12/45 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Pilatus Aircraft Ltd. (Pilatus) Models PC-12 and PC-12/45 airplanes. This AD requires you to insert a temporary revision into the Limitations Section of the Pilot Operating Handbook (POH). This AD also requires you to replace the pitch actuator with an improved design pitch actuator and make the necessary wiring and circuit breaker changes, as applicable. Installing the improved design pitch actuator terminates the need for the temporary revision in the POH. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. We are issuing this AD to prevent an out-of-trim condition from occurring when the flaps are at a 40-degree flight phase and the pilot disconnects the autopilot. This condition could lead to reduced ability to control the airplane.
AD 2005-12-02 · published Jun 10, 2005, effective Jul 8, 2005
Revo, Incorporated Models Colonial C-2, Lake LA-4, Lake LA-4A, Lake LA-4P, and Lake LA-4-200 Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede Airworthiness Directive (AD) 98-10-12, which applies to all Revo, Incorporated (REVO) (Type Certificate 1A13 formerly held by Colonial Aircraft Company, Lake Aircraft Corporation, Consolidated Aeronautics, Inc., and Global Amphibians LLC) Models Colonial C-2, Lake LA-4, Lake LA-4A, Lake LA-4P, and Lake LA-4-200 airplanes. AD 98-10-12 currently requires you to ensure adequate clearance between the attachment fitting and the horizontal stabilizer rear beam and between the attachment fitting and the stabilizer skin with inspections, possible replacement, and adjustments as necessary. This new AD is the result of several reports of fatigue cracks found in the horizontal stabilizer attachment fitting (part number 2-2200-21) of Model LA-4-200 airplanes that were in compliance with AD 98-10-12. This includes an airplane accident with a fatality attributed to a fatigue crack in the horizontal stabilizer attachment fitting. Consequently, this AD requires either a dye penetrant inspection of the horizontal stabilizer attachment fitting for any evidence of fretting, cracking, or corrosion (with necessary replacement and modification) or replacement of the fittings depending on the number of operational hours on the fitting. The AD also requires you to repetitively replace the fitting every 850 hours time-in-service (TIS), repetitively inspect (visually) the fittings between replacement times, and report to FAA the results of the initial inspection and any cracks found on repetitive inspections. We are issuing this AD to detect, correct, and prevent future cracks in the horizontal stabilizer attachment fitting, which could result in failure of the horizontal stabilizer attachment fitting. This failure could result in loss of control of the airplane.
AD 2005-12-04 · published Jun 14, 2005, effective Jun 29, 2005
Boeing Model 757-200, -200PF, and -200CB Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757-200, -200PF, and -200CB series airplanes. This AD requires repetitive inspections of the shim installation between the vertical flange and bulkhead. This AD is prompted by reports of cracks, loose and broken bolts, and shim migration in the joint between the aft torque bulkhead and the strut-to-diagonal brace fitting. We are issuing this AD to detect and correct such cracks, loose and broken bolts, and shim migration, which could result in damage to the strut and consequent separation of the strut and engine from the airplane.
AD 2005-12-05 · published Jun 14, 2005, effective Jul 19, 2005
Boeing Model 737-200, 737-300, 737-400, 737-500, 737-600, 737-700, 737-800, 737-900, 757-200, and 757-300 Series Airplanes; and McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-30, DC-10-30F, DC-10-40, MD-10-10F, MD-10-30F, MD-11, and MD-11F Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain transport category airplanes. That AD currently requires modification of the reinforced flight deck door. This new AD expands the applicability of the existing AD and requires other actions related to the reinforced flight deck door. These other actions include modifying the door, inspecting and modifying wiring in the area, and revising the maintenance program to require more frequent testing of the decompression panels of the flight deck door. This AD is prompted by reports of discrepancies with the reinforced flight deck door. We are issuing this AD to prevent inadvertent release of the decompression latch and consequent opening of the decompression panel in the flight deck door, or penetration of the flight deck door by smoke or shrapnel, any of which could result in injury to the airplane flightcrew. This AD also requires finding and fixing wire chafing, which could result in arcing, fire, and/or reduced controllability of the airplane.
AD 2005-12-09 · published Jun 14, 2005, effective Jul 28, 2005
GROB-WERKE Model G120A Airplanes
The FAA adopts a new airworthiness directive (AD) for all GROB-WERKE (GROB) Model G120A airplanes. This AD requires you to repetitively inspect the nose landing gear (NLG) assembly, paying special attention to the NLG swivel tube and the engine truss in the area of the NLG attachment, for cracks and damaged (defective) welding seams. If you find cracks or defects during any inspection, this AD requires you to replace the cracked or defective part. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to detect and correct cracks and defects in the NLG assembly, which could result in failure of the NLG. This failure could lead to a hard landing and/or loss of control of the airplane during landing operations.
AD 2005-12-12 · published Jun 14, 2005, effective Jun 22, 2005
Cessna Aircraft Company Models 401, 401A, 401B, 402, 402A, 402B, 411, and 411A Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede AD 79-10-15, which applies to all Cessna Aircraft Company (Cessna) Models 401, 401A, 401B, 402, 402A, 402B, 411, and 411A airplanes. AD 79-10-15 currently requires repetitive inspections of the right and left wing spar lower cap areas for fatigue cracks and requires wing spar cap repair or replacement as necessary. This AD is the result of fatigue and crack growth analyses of the wings of these airplanes, recent cracks found on similar design Model 402C airplanes, and the FAA's determination that repetitive inspections and a wing spar modification are necessary to address the unsafe condition. Consequently, this AD would require repetitive inspections and a spar strap modification on each wing. The actions specified by this AD are intended to prevent wing spar cap failure caused by undetected fatigue cracks. Such failure could result in loss of a wing with consequent loss of airplane control. FAA is also issuing AD 2005-12-13 to require the spar strap modification and long-term inspections on Models 402C and 414A airplanes.
AD 2005-12-13 · published Jun 14, 2005, effective Jun 22, 2005
Cessna Aircraft Company Models 402C and 414A Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede AD 2005-05-52 (70 FR 13362, March 21, 2005), which applies to all Cessna Aircraft Company (Cessna) Models 402C and 414A airplanes. AD 2005-05-52 currently requires you to eddy current inspect the forward wing spars and visually inspect the aft and auxiliary spars. This AD is the result of fatigue and crack growth analyses of the wings of these airplanes, recent cracks found on Model 402C airplanes, and the FAA's determination that repetitive inspections and a wing spar modification are necessary to address the unsafe condition. Consequently, this AD would require repetitive eddy current inspections, visual inspections, and a spar strap modification on each wing. You must retain the actions of AD 2005-05-52 until you do the modifications of this AD. The actions specified by this AD are intended to prevent wing spar cap failure caused by undetected fatigue cracks. Such failure could result in loss of a wing with consequent loss of airplane control. FAA is also issuing AD 2005-12-12 to require the spar strap modification and long-term inspections on Models 401, 401A, 402, 402A, 402B, 411, and 411A airplanes.
AD 2005-12-07 · published Jun 15, 2005, effective Jun 30, 2005
Airbus Model A319, A320, and A321 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A319, A320, and A321 series airplanes. This AD requires a one-time ultrasonic inspection for certain airplanes, and repetitive detailed inspections for all airplanes, for cracking in the forward lug of the support rib 5 fitting of both main landing gear (MLG), and repair if necessary. This AD also provides for optional terminating actions. This AD is prompted by a report of a crack found in the forward lug of the right-hand MLG rib 5 fitting during greasing of both MLG pintle bearings. We are issuing this AD to find and fix cracking in the forward lug of the MLG, which could result in failure of the lug and consequent collapse of the MLG during landing.
AD 2005-12-10 · published Jun 15, 2005, effective Jul 20, 2005
Boeing Model 747-200F and -400 Series Airplanes; Model 767-400ER Series Airplanes; and Model 777 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-200F and -400 series airplanes; Model 767- 400ER series airplanes; and Model 777 series airplanes. This AD requires replacing the frequency converter(s) used to supply electrical power for utility outlets (for the galley, medical equipment, or personal computers) with modified frequency converter(s). This AD also requires any specified action and related concurrent actions, as necessary. This AD is prompted by a report that a hard short condition between the frequency converter's output and its downstream circuit breakers will produce a continuous current that could cause the undersized output wiring to overheat. We are issuing this AD to prevent the overheating of the frequency converter's undersized output wiring, which could lead to the failure of a wire bundle, and consequent adverse effects on other systems sharing the affected wire bundle.
AD 2005-12-11 · published Jun 15, 2005, effective Jul 20, 2005
Boeing Model 757-200 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757-200 series airplanes. This AD requires modifying the frequency converters located in the closet assembly in the passenger compartment, and making various wiring changes in and between the closet assembly and forward purser work station. This AD also requires modifying the in-flight entertainment system prior to or concurrently with the modification of the frequency converters. This AD is prompted by a certification review that revealed a frequency converter failure mode not identified in the original system design. We are issuing this AD to prevent a short circuit between the frequency converter output and the distribution circuit breakers, which could result in overheating and failure of adjacent wiring and consequent adverse effects on other systems sharing the affected wire bundle.
AD 2005-12-14 · published Jun 15, 2005, effective Jun 30, 2005
Boeing Model 767-200, -300, and -400ER Series Airplanes Equipped With Door-Mounted Escape Slides
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200, -300, and -400ER series airplanes. This AD requires an inspection to determine if the door-mounted escape slide/rafts have certain part numbers. For those door-mounted escape slide/rafts having certain part numbers, this AD requires an inspection for excessive tension of the firing cable, and procedures for providing slack in the firing cable or rerouting the firing cable if necessary. This AD is prompted by reports of uncommanded inflation inside the airplane of a door-mounted escape slide/raft located in the passenger compartment. We are issuing this AD to prevent injury to maintenance personnel, passengers, and crew during otherwise normal operating conditions and to prevent interference with evacuation of the airplane during an emergency, due to uncommanded inflation of a door-mounted escape slide/raft.
AD 2005-12-15 · published Jun 15, 2005, effective Jul 20, 2005
Bombardier Model DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires revising the Airworthiness Limitation section of the Instructions for Continued Airworthiness of the Dash 8 400 Series (Bombardier) Maintenance Requirements Manual to reduce the life limits of the main landing gear (MLG) orifice support tube, upper bearing, and piston plug; and to reduce the threshold for initiating repetitive detailed inspections for cracking of the engine isolator brackets. This AD is prompted by the discovery of fatigue failures, during type certification fatigue testing, at the engine isolator bracket and at the orifice support tube, upper bearing, and piston plug in the shock strut assembly of the MLG, which are principal structural elements. We are issuing this AD to prevent the development of cracks in these principal structural elements, which could reduce the structural integrity of the engine installation and the MLG. Reduced structural integrity of the engine installation could result in separation of the engine from the airplane, and reduced structural integrity of the MLG could result in collapse of the MLG.
AD 2005-12-16 · published Jun 15, 2005, effective Jul 20, 2005
Fokker Model F.28 Mark 0100 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F.28 Mark 0100 airplanes. This AD requires an inspection to determine the part number of the passenger service unit (PSU) panels for the PSU modification status, and corrective actions if applicable. This AD is prompted by reported incidents of smoke in the passenger compartment during flight. One of those incidents also included a burning smell and consequently led to emergency evacuation of the airplane. We are issuing this AD to prevent overheating of the PSU panel due to moisture ingress, which could result in smoke or fire in the passenger cabin.
AD 2005-12-17 · published Jun 17, 2005, effective Jul 5, 2005
Bombardier Model DHC-8-400 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires inspecting the electrical connectors of the fire extinguisher bottles for the forward and aft baggage compartments and for the auxiliary power unit and engine nacelles to determine if they are connected correctly; and doing related investigative and corrective actions, if necessary. This AD is prompted by reports of the electrical connectors for the fire bottles in the forward and aft baggage compartments being cross connected. We are issuing this AD to detect and correct cross connection of the fire extinguisher bottles, which could result in failure of the fire bottles to discharge and consequent inability to extinguish a fire in the affected areas.
AD 2005-12-18 · published Jun 17, 2005, effective Jul 22, 2005
Boeing Model 757 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Boeing Model 757 series airplanes. For certain affected airplanes, this action requires repetitive testing of the secondary brakes of the horizontal stabilizer trim actuator (HSTA). For all affected airplanes, this action requires repetitive overhauls of the primary brake and differential assembly of the HSTA, which would constitute terminating action for the repetitive testing of the secondary brake. This action is necessary to prevent grease contamination on the primary HSTA brake and consequent loss of the primary brake function, which, in combination with the loss of the secondary HSTA brake function, could result in loss of control of the airplane. This action is intended to address the identified unsafe condition.
AD 2005-12-20 · published Jun 20, 2005, effective Jun 21, 2005
The Lancair Company Model LC41-550FG Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Lancair Company (Lancair) Model LC41-550FG airplanes. This AD requires both visual and dye penetrant inspections of the elevator torque tube assembly for cracks. If a crack is found, this AD requires replacement with a modified assembly that incorporates a steel doubler. This AD also requires replacement of the modified elevator torque tube assembly every 300 hours time-in-service or 18 months (whichever occurs first). This AD results from cracks found in the weld area of the elevator torque tube assembly. We are issuing this AD to detect and correct cracks in the elevator torque tube assembly, which could result in failure of the elevator torque tube assembly and subsequent loss of control of the airplane.
AD 2005-13-03 · published Jun 21, 2005, effective Jul 26, 2005
AvCraft Dornier Model 328-100 and -300 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain AvCraft Dornier Model 328-100 and -300 airplanes. This AD requires operators to install colored identification strips on the pulley brackets, fairlead bracket assemblies, operational assemblies, and flight control cables. This AD is prompted by a report that the flight control systems do not have elements that are distinctively identified. We are issuing this AD to prevent the incorrect re-assembly of the flight control system during maintenance, which could result in reduced controllability of the airplane.
AD 2005-13-04 · published Jun 21, 2005, effective Jul 26, 2005
Avcraft Dornier Model 328-100 and -300 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Avcraft Dornier Model 328-100 and -300 airplanes. This AD requires a pressure test and detailed inspection of each fuselage drain line to determine if there is a blockage, and related investigative/ corrective actions if necessary. This AD is prompted by a report of leakage at one of the drain lines in the fuselage. We are issuing this AD to prevent blockage within the drain lines, causing fluids to collect. These fluids may freeze and expand, damaging the drain lines, and allowing fuel to leak into the cabin and fuel vapors to come into contact with ignition sources, which could result in consequent fire in the cabin.
AD 2005-13-06 · published Jun 21, 2005, effective Jul 26, 2005
BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ airplanes. This AD requires modifying the auxiliary power unit (APU) exhaust duct in the environmental control system (ECS) bay; installing new, improved insulation on this APU exhaust duct; and replacing the existing drain pipe with a new exhaust drain pipe blank. This AD is prompted by a determination that the temperature of the skin of the APU exhaust duct in the ECS bay is higher than the certificated maximum temperature for this area. We are issuing this AD to prevent the potential for ignition of fuel or hydraulic fluid, which could leak from pipes running through the ECS bay. Ignition of these flammable fluids could result in a fire in the ECS bay.
AD 2005-13-02 · published Jun 22, 2005, effective Jul 27, 2005
Bombardier Model CL-600-2C10 (Regional Jet Series 700 & 701) Series Airplanes, and Model CL-600-2D24 (Regional Jet Series 900) Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2C10 (Regional Jet series 700 & 701) series airplanes, and Model CL-600-2D24 (Regional Jet series 900) series airplanes. This AD requires revising the Airworthiness Limitations section of the Instructions of Continued Airworthiness by incorporating new repetitive inspections and an optional terminating action for the repetitive inspections, and repairing any crack. This AD is prompted by reports of hydraulic pressure loss in either the number 1 or number 2 hydraulic system due to breakage or leakage of hydraulic lines in the aft equipment bay and reports of cracks on the aft pressure bulkhead web around these feed-through holes. We are issuing this AD to prevent loss of hydraulic pressure, which could result in reduced controllability of the airplane, and to detect and correct cracks on the aft pressure bulkhead web, which could result in reduced structural integrity of the aft pressure bulkhead.
AD 2005-13-05 · published Jun 22, 2005, effective Jul 27, 2005
Boeing Model 747-400F Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-400F series airplanes. This AD requires initial detailed and open-hole high frequency eddy current inspections for cracking of the web, upper chord, and upper chord strap of the upper deck floor beams, and repair of any cracking. This AD also requires a preventive modification of the upper deck floor beams, and repetitive inspections for cracking after accomplishing the modification. This AD is prompted by reports of fatigue cracking found on the upper deck floor beam to frame attachment points. We are issuing this AD to prevent fatigue cracks in the upper chord, upper chord strap, and the web of the upper deck floor beams and resultant failure of the floor beams. Failure of a floor beam could result in damage to critical flight control cables and wire bundles that pass through the floor beam, and consequent loss of controllability of the airplane. Failure of the floor beam also could result in the failure of the adjacent fuselage frames and skin, and consequent rapid decompression of the airplane.
AD 2005-13-08 · published Jun 22, 2005, effective Jul 27, 2005
BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited (Jetstream) Model 4101 airplanes. This AD requires the overhaul of certain auxiliary components installed on the main landing gear (MLG) and nose landing gear (NLG). This AD is prompted by manufacturer determination that overhaul limits need to be imposed for certain auxiliary components of the MLG and NLG. Components that exceed the established overhaul limits could fail due to fatigue, wear, and age. We are issuing this AD to prevent failure of the MLG or NLG, and consequent damage to the airplane and injury to flightcrew and passengers.
AD 2005-13-10 · published Jun 22, 2005, effective Aug 9, 2005
Cessna Aircraft Company Models 172R, 172S, 182T, T182T, 206H, and T206H Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, T182T, 206H, and T206H airplanes. This AD requires you to inspect any MC01-3A I.C. 9 or MC01-3A I.C. 10 main electrical power junction box circuit breakers for correct amperage (amp) (a correct 40-amp circuit breaker) and replace any incorrect amp circuit breaker with the correct 40-amp circuit breaker. This AD results from several reports of circuit breakers that are not the correct 40-amp circuit breaker installed in the MC01-3A main electrical power junction box. We are issuing this AD to replace any incorrect circuit breaker installed in the MC01-3A I.C. 9 or MC01-3A I.C. 10 main electrical power junction box, which could result in premature tripping of the power junction box main feeder circuit breakers and could lead to partial or complete loss of all electrical power on the airplane. This condition could lead to the loss of all navigation and communication equipment and lighting in the cockpit.
AD 2005-13-12 · published Jun 22, 2005, effective Aug 5, 2005
Air Tractor, Inc. Models AT-300, AT-301, AT-302, AT-400, AT-400A, AT-401, AT-402, AT-602, AT-802, and AT-802A Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Air Tractor, Inc. (Air Tractor) Models AT-300, AT-301, AT-302, AT-400, AT-400A, AT-401, AT-402, AT-602, AT-802, and AT-802A airplanes. This AD requires you to repetitively tighten the four eyebolts that attach the front and rear spar of the horizontal stabilizer to the respective stabilizer strut to the specified torque, and repetitively replace at specified intervals any eyebolts that attach the front and rear spar of the horizontal stabilizer to the respective stabilizer strut. An option for replacing the steel brace assembly inside the stabilizer with a new steel brace assembly with larger bushings and stronger eyebolts that increases the interval for replacement of eyebolts for AT-602, AT-802, and AT-802A airplanes is also included in this AD. This AD results from reports of failures of the subject eyebolt. We are issuing this AD to detect, correct, and prevent future fatigue failure in any eyebolt that attaches the front and rear spar of the horizontal stabilizer to the respective stabilizer strut. Failure of the eyebolt could lead to an abrupt change or complete loss of pitch control and/or the airplane departing from controlled flight.
AD 2005-13-16 · published Jun 22, 2005, effective Aug 8, 2005
The New Piper Aircraft, Inc. PA-34 Series Airplanes
The FAA adopts an airworthiness directive to supersede AD 93- 24-14 applicable to all The New Piper Aircraft, Inc. (Piper) PA-34 series airplanes. This AD results from many service difficulty reports related to the collapse of the nose landing gear (NLG). Consequently, this AD retains the actions required in AD 93-24-14, requires you to inspect the NLG and components of the NLG using new procedures for rigging the nose gear installation, and requires you to replace unserviceable parts. We are issuing this AD to detect, correct, and prevent failure in certain components of the NLG, lack of cleanliness of the NLG due to inadequate maintenance, or lack of lubricant in the NLG or NLG components. This failure of the NLG could lead to loss of control of the airplane during take-off, landing, or taxiing operations.
AD 2005-12-19 · published Jun 24, 2005, effective Jul 29, 2005
Airbus Model A319, A320, and A321 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A319, A320, and A321 series airplanes. This AD requires replacing the cargo ventilation extraction duct at frame 65 with a new duct, and relocating the temperature sensor in the aft cargo compartment. This AD is prompted by a report indicating that, during a test of the fire extinguishing system, air leakage around the temperature sensor for the aft cargo compartment reduced the concentration of fire extinguishing agent to below the level required to suppress a fire. We are issuing this AD to prevent air leakage around the temperature sensor for the aft cargo compartment, which, in the event of a fire in the aft cargo compartment, could result in an insufficient concentration of fire extinguishing agent, and consequent inability of the fire extinguishing system to suppress the fire.
AD 2005-13-14 · published Jun 24, 2005, effective Jul 29, 2005
McDonnell Douglas Model MD-90-30 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all McDonnell Douglas Model MD-90-30 airplanes. This AD requires replacing existing dual anti-skid control manifolds (DACM) with new, improved or reworked and reidentified DACMs; inspecting the inlet filters and other components of the DACMs for damage; replacing any damaged DACM components with new or serviceable components; and flushing/cleaning the braking system prior to replacing the inlet filters. This AD is prompted by reports of multiple incidents of blown tires on landing while using maximum autobrake. We are issuing this AD to prevent metallic fibers from the first stage filter of the servo valves inside the DACM from becoming lodged in the first stage nozzle of the servo valve, which could lead to tire failure during high speed/high energy braking and possible subsequent runway departure.
AD 2005-13-15 · published Jun 24, 2005, effective Jul 29, 2005
Boeing Model 737-200, -200C, -300, -400, -500, -600, -700, -700C, -800, and -900 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-200, -200C, -300, -400, -500, -600, -700, - 700C, -800, and -900 series airplanes. This AD requires a one-time detailed inspection for discrepancies of the secondary fuel vapor barrier of the wing center section, and related investigative/ corrective actions if necessary. This AD is prompted by reports that the secondary fuel vapor barrier was not applied correctly to, or was missing from, certain areas of the wing center section. We are issuing this AD to prevent fuel or fuel vapors from leaking into the cargo or passenger compartments and coming into contact with a possible ignition source, which could result in fire or explosion.
AD 2005-13-20 · published Jun 24, 2005, effective Jul 29, 2005
Boeing Model 747-400, -400D, -400F; 767-200, -300, -300F; and 777-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-400, -400D, -400F; 767-200, -300, -300F; and 777-200 and -300 series airplanes. This AD requires installing a jumper wire between the wiring of the fire extinguisher switch and the fuel shutoff switch for each engine, and other specified actions. This AD is prompted by a certain combination of conditions, which could cause the fuel spar shutoff valves to remain partially open. We are issuing this AD to prevent a latent open circuit that could leave the fuel spar shutoff valve in a partially open position when the engine fire switch is activated, which could result in fuel from the engine feeding an uncontrolled fire in the engine or the strut.
AD 2005-13-21 · published Jun 24, 2005, effective Jul 29, 2005
Cessna Model 650 Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Cessna Model 650 airplanes, that requires inspecting to determine the part number of the actuator control unit (ACU) and replacing the ACU with a new, improved ACU if necessary. This AD also requires revising the Limitations section of the airplane flight manual. The actions specified by this AD are intended to prevent uncommanded movement of the horizontal stabilizer, which could result in reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
AD 2005-13-24 · published Jun 24, 2005, effective Jul 29, 2005
AvCraft Dornier Model 328-100 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all AvCraft Dornier Model 328-100 airplanes. This AD requires modifying the electrical wiring of the fuel pumps; installing insulation at the hand flow control and shut-off valves, and other components of the environmental control system; and installing markings at fuel wiring harnesses. This AD also requires revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness to incorporate new inspections of the fuel tank system. This AD is prompted by the results of fuel system reviews conducted by the airplane manufacturer. We are issuing this AD to reduce the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
AD 2005-13-18 · published Jun 27, 2005, effective Aug 1, 2005
McDonnell Douglas Model DC-9-10 Series Airplanes; Model DC-9-20 Series Airplanes; Model DC-9-30 Series Airplanes; Model DC-9-40 Series Airplanes; Model DC-9-50 Series Airplanes; Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), and DC-9-87 (MD-87) Airplanes; and Model MD-88 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain SAFT America Inc. part number (P/N) 021929-000 (McDonnell Douglas P/N 43B034LB02) and P/N 021904-000 (McDonnell Douglas P/N 43B034LB03) nickel cadmium batteries. That AD currently requires replacing all battery terminal screws, verifying that the battery contains design specification cells, and replacing the cells if the battery contains non-design specification cells. This new AD requires an inspection for certain nickel cadmium batteries and, if necessary, replacing battery terminal screws with new hex head bolts and adding shims. This AD is prompted by a report of battery screws shearing off while under normal torque loads. We are issuing this AD to prevent internal shorting, arcing, and loss of emergency battery power due to failed battery screws, which could result in loss of emergency power to electrical flight components or other emergency power systems required in the event of loss of the aircraft primary power source.
AD 2005-13-26 · published Jun 27, 2005, effective Aug 1, 2005
Airbus Model A300 B2 and B4 Series Airplanes; Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes); and Model A310-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus models, as specified above. This AD requires installing safety signs on all passenger/crew doors, emergency exit doors, and cargo compartment doors. This AD is prompted by a report of injuries occurring on in-service airplanes when crewmembers forcibly initiated opening of passenger/crew doors against residual pressure causing the doors to rapidly open. We are issuing this AD to ensure that crewmembers are informed of the risks associated with forcibly opening passenger/crew, emergency exit, and cargo doors before an airplane is fully depressurized, which will prevent injury to crewmembers, and subsequent damage to the airplane caused by the rapid opening of the door.
AD 2005-13-27 · published Jun 27, 2005, effective Aug 1, 2005
Boeing Model 737-300, -400, and -500 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-300, -400, and -500 series airplanes. This AD requires repetitive inspections for cracking of the crown area of the fuselage skin, and corrective actions if necessary. This AD is prompted by a Model 737 fuselage structure test and fatigue analysis that indicate fuselage skin cracking could occur between 21,000 and 42,000 total flight cycles. We are issuing this AD to detect and correct fatigue cracking of the fuselage skin, which could cause the fuselage skin to fracture and fail, and could result in rapid decompression of the airplane.
AD 2005-13-28 · published Jun 27, 2005, effective Aug 1, 2005
Boeing Model 777-200 and -300 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 777-200 and -300 series airplanes. This AD requires a one-time inspection of the clevis end of the vertical tie rods that support the center stowage bins to measure the exposed thread, installation of placards that advise of weight limits for certain electrical racks, a one-time inspection and records check to determine the amount of weight currently installed in those electrical racks, corrective actions, and replacement of the vertical tie rods for the center stowage bins or electrical racks with new improved tie rods, as applicable. The actions specified by this AD are intended to prevent failure of the vertical tie rods supporting certain electrical racks and the center stowage bins, which could cause the center stowage bins or electrical racks to fall onto passenger seats below during an emergency landing, impeding an emergency evacuation or injuring passengers. This action is intended to address the identified unsafe condition.
AD 2005-13-29 · published Jun 27, 2005, effective Aug 1, 2005
Boeing Model 777-200 and -300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 777-200 and -300 series airplanes. This AD requires inspecting for the installation of the tie plate for the wire bundles routed from lower section 41 into the center control stand in the flight deck; inspecting for any wire chafing or damage and repair if necessary; and installing a tie plate if necessary. This AD is prompted by a report of missing tie plates for the wire bundles. We are issuing this AD to prevent wire chafing, which could result in the loss of flight control, communication, navigation, and engine fire control systems. Loss of these systems could consequently result in a significant reduction of safety margins, an increase in flight crew workload, and in the case where loss of engine fire control is combined with an engine fire, could result in an uncontrollable fire.
AD 2005-13-30 · published Jun 27, 2005, effective Aug 1, 2005
Boeing Model 737-100, -200, and -200C Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Boeing Model 737-100, -200, and -200C series airplanes, that requires repetitive inspections to detect discrepancies of certain fuselage skin panels located just aft of the wheel well, and repair if necessary. The actions specified by this AD are intended to detect and correct fatigue cracking of the skin panels, which could cause rapid decompression of the airplane. This action is intended to address the identified unsafe condition.
AD 2005-13-32 · published Jun 27, 2005, effective Aug 1, 2005
Fokker Model F.28 Mark 1000, 2000, 3000, and 4000 Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F.28 Mark 1000, 2000, 3000, and 4000 airplanes. This AD requires a detailed inspection to determine the presence of incorrectly installed bushings in the attachment holes of the reinforcing strap of the left- and right-hand wings' lower skin, and corrective actions if necessary. This AD is prompted by a report that bushings were installed in accordance with improper procedures in the structural repair manual. We are issuing this AD to detect and correct improperly installed bushings, which could result in reduced tensile strength of the reinforcing strap of the wing's lower skin, and consequently a reduction of the structural capability of the wing and possible wing failure.
AD 2005-13-33 · published Jun 27, 2005, effective Aug 1, 2005
Airbus Model A300 B2 and B4 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A300 B2 and B4 series airplanes. This AD requires modifying the wiring of the autopilot pitch torque limiter switch. This AD is prompted by several reports of pitch trim disconnect caused by insufficient length in the wiring to the pitch torque limiter lever. We are issuing this AD to prevent possible trim loss when the flightcrew tries to override the autopilot pitch control, which could result in uncontrolled flight of the airplane.
AD 2005-13-19 · published Jun 28, 2005, effective Aug 2, 2005
BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ series airplanes. This AD requires repetitive external eddy current inspections of the forward fuselage skin to detect cracking due to fatigue, and repair if necessary. This AD is prompted by evidence of cracking due to fatigue along the edges of the chemi-etched pockets in certain front fuselage canopy skin panels. We are issuing this AD to detect and correct this cracking, which could result in reduced structural integrity of the airplane fuselage.
AD 2005-13-31 · published Jun 28, 2005, effective Aug 2, 2005
Short Brothers Model SD3-60 Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Short Brothers Model SD3-60 airplanes, that requires performing repetitive inspections of the shear attachment fittings of the vertical stabilizer for corrosion, and performing corrective actions if necessary. The actions specified by this AD are intended to detect and correct corrosion in the area of the main spar web fittings of the vertical stabilizer, which could result in reduced structural integrity of the vertical stabilizer. This action is intended to address the identified unsafe condition.
AD 2005-13-34 · published Jun 28, 2005, effective Aug 2, 2005
Boeing Model 777-200 and -300 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 777-200 and -300 series airplanes, that requires replacing existing ceiling and sidewall light connectors in the passenger cabin with new connectors, and follow-on actions. This action is necessary to prevent overheating of the light connectors, which could result in smoke and a possible fire in the passenger cabin. This action is intended to address the identified unsafe condition.
AD 2005-13-40 · published Jun 30, 2005, effective Aug 4, 2005
Boeing Model 727 Airplanes, Equipped With an Auxiliary Fuel Tank Having a Fuel Pump Installed
The FAA is adopting a new airworthiness directive (AD) for Boeing Model 727 airplanes equipped with an auxiliary fuel tank having a fuel pump installed. This AD requires revising the airplane flight manual to include limitations on operating the fuel pumps for the auxiliary fuel tank. This AD is prompted by a design review of the fuel pump installation, which revealed a potential unsafe condition related to the auxiliary fuel tank(s). We are issuing this AD to prevent dry operation of the fuel pumps for the auxiliary fuel tank, which could create a potential ignition source inside the auxiliary fuel tank that could result in a fire or explosion of the auxiliary fuel tank.
AD 2005-12-01 · published Jun 8, 2005, effective Jul 13, 2005
Agusta S.p.A. Model A109E Helicopters
This amendment adopts a new airworthiness directive (AD) for Agusta S.p.A. (Agusta) Model A109E helicopters that requires, within 5 hours time-in-service (TIS), locating relay K7212 and its associated cable in the overhead panel assembly and visually inspecting the electrical cable in the splice area for arcing or burns. If arcing or burns are found, this AD requires, before further flight, replacing an unairworthy cable with an airworthy cable kit. This AD is prompted by an overhead panel inspection report of incorrect crimping of the pins on the cable that connects to the relay. An electrical cable fault during assembly could result in arcing or burning of the cable junction at a relay in the overhead electrical panel. The actions specified by this AD are intended to detect arcing or burns of the cable or relay and to prevent burning of the cable junction at a relay, a fire in the cockpit, and subsequent loss of control of the helicopter.
AD 2005-12-03 · published Jun 14, 2005, effective Jun 29, 2005
Sikorsky Aircraft Corporation Model S-92A Helicopters
This amendment adopts a new airworthiness directive (AD) for Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopters. This action requires replacing the main gearbox (MGB) lubrication/scavenge pump vespel spline adapters (vespel spline adapters) before further flight, and thereafter, replacing them at certain intervals. This amendment is prompted by a reported incident of an in-flight loss of oil pressure. The actions specified in this AD are intended to prevent loss of lubrication to the MGB, which could cause failure of one or both engine input drives, or planetary gear to sun gear tooth mesh failure, resulting in loss of power to the rotor system and subsequent loss of control of the helicopter.
AD 2005-13-13 · published Jun 23, 2005, effective Jul 8, 2005
Sikorsky Aircraft Corporation Model S-92A Helicopters
This amendment adopts a new airworthiness directive (AD) for the Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopters. This action requires replacing a certain part-numbered tail gear box output housing that has 600 or more hours time-in-service (TIS) with an airworthy part. Also, this AD revises the Airworthiness Limitations section of the maintenance manual by reducing the life limit of the tail gear box output housing. This amendment is prompted by the premature failure of the tail gear box output housing during fatigue testing by the manufacturer. The actions specified in this AD are intended to prevent fatigue failure of the tail gear box output housing, loss of tail rotor drive, and subsequent loss of control of the helicopter.
AD 2005-13-17 · published Jun 24, 2005, effective Jul 11, 2005
Agusta S.p.A. Model AB412 Series Helicopters
This amendment adopts a new airworthiness directive (AD) for the Agusta S.p.A. (Agusta) Model AB412 Series helicopters. This action requires inspecting each affected tail rotor blade (blade) forward tip weight retention block (tip block) and the aft tip closure (tip closure) for adhesive bond voids, and removing any blade with an excessive void from service. This AD also requires modifying certain blades by installing shear pins and tip closure rivets on all affected blades. This amendment is prompted by reports of in-flight loss of tip blocks and tip closures resulting in minor to substantial damage. The actions specified in this AD are intended to prevent loss of the tip block or tip closure, loss of a blade, and subsequent loss of control of the helicopter.
AD 2005-13-23 · published Jun 24, 2005, effective Jul 29, 2005
Eurocopter France Model EC 155B, EC155B1, SA-365N, SA-365N1, AS-365N2, and AS 365 N3 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for Eurocopter France (Eurocopter) Model EC 155B, SA-365N and N1, AS-365N2, and AS 365 N3 helicopters. That AD currently requires inspecting the hydraulic brake hose (hose) for crazing, pinching, distortion, or leaks at the torque link hinge and replacing the hose, if necessary. That AD also requires inspecting the hose and the emergency flotation gear pipe to ensure adequate clearance, and adjusting the landing gear leg, if necessary. This amendment requires the same actions as the existing AD and adds another model helicopter to the applicability. This amendment is prompted by notification by the manufacturer and the European Authority that another affected model helicopter, the Model EC155B1, may have the same unsafe condition and should be added to the existing AD. The actions specified by this AD are intended to prevent failure of a hose, resulting in failure of hydraulic pressure to the brakes on the affected landing gear wheel, and subsequent loss of control of the helicopter during a run-on landing.
AD 2005-12-08 · published Jun 14, 2005, effective Jun 29, 2005
Turbomeca S.A. Arrius 2 B1, 2 B1A, 2 B1A-1, and 2 B2 Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for Turbomeca S.A. Arrius 2 B1, 2 B1A, 2 B1A-1, and 2 B2 turboshaft engines. This AD requires replacing the software in the Engine Electronic Control Unit (EECU). This AD results from a report of simultaneous loss of automatic control of both engines of a Eurocopter Deutschland EC 135 helicopter, during flight. We are issuing this AD to prevent simultaneous loss of automatic control of both engines and subsequent loss of control of the helicopter.
AD 2005-13-11 · published Jun 21, 2005, effective Jul 6, 2005
General Electric Company CT64-820-4 Turboprop Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CT64-820-4 turboprop engines with stage 1 turbine disk and shaft, part number (P/N) 6004T47P03 or 4921T10P02 installed. This AD requires removing from service these stage 1 turbine disk and shafts at reduced compliance times. This AD results from the discovery by the manufacturer of low-cycle-fatigue (LCF) cracks found in stage 1 turbine disk and shafts, P/Ns 6004T47P03 and 4921T10P02. We are issuing this AD to prevent uncontained failure of the stage 1 turbine disk and shaft, resulting in damage to the airplane.
AD 2005-13-07 · published Jun 22, 2005, effective Jul 27, 2005
Honeywell International Inc. (Formerly AlliedSignal Inc. and Garrett Turbine Engine Co.) TFE731-2 and -3 Series Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Honeywell International Inc. (formerly AlliedSignal Inc. and Garrett Turbine Engine Co.) TFE731-2 and -3 series turbofan engines with certain part numbers (P/Ns) and serial numbers (SNs) of low pressure (LP) 1st and 2nd stage turbine rotor discs initially installed. This AD requires replacement of those LP 1st and 2nd stage turbine rotor discs. This AD results from a report of an uncontained failure of an LP 2nd stage turbine rotor disc that resulted in an in-flight engine shutdown. We are issuing this AD to prevent LP turbine rotor disk separation, which could result in an uncontained engine failure and damage to the airplane.
AD 2005-13-25 · published Jun 24, 2005, effective Jul 11, 2005
Turbomeca S.A. Arriel 2B Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for Turbomeca S.A. Arriel 2B turboshaft engines with Modification TU62A incorporated. This AD results from several reports of the hydromechanical unit (HMU) acceleration controller axle sticking. This AD requires initial and repetitive inspections, cleaning, lubrication, and checks for proper operation of the HMU acceleration controller axle. We are issuing this AD to prevent loss of control of engine fuel flow in manual control mode or mixed control mode, leading to engine overspeed and in-flight engine shutdown, or uncommanded in-flight engine shutdown.
AD 2005-13-01 · published Jun 22, 2005, effective Jul 7, 2005
[Hoffmann Propeller GmbH & Co KG Models HO-V343 and HO-V343K Propellers]
The FAA is superseding an existing airworthiness directive (AD) for Hoffmann Propeller GmbH & Co KG Models HO-V343 and HO-V343K propellers. That AD currently requires initial and repetitive visual inspections of propeller blades for blade shake and blade nut preload. That AD also requires initial and repetitive eddy current inspections of blade hubs for damage and cracks. This AD requires an ultrasonic inspection of the propeller hub and an eddy current inspection of the propeller hub if any cracks are discovered during ultrasonic inspection. Additionally, this AD requires sending a hub inspection report to the manufacturer. This AD also requires replacement of the propeller if any signs of blade shake, cracks, or other damage to the propeller hub outside serviceable limits are detected during the inspections. This AD results from the discovery of a propeller blade separation due to a possible hub failure. We are issuing this AD to prevent propeller hub failure and blade separation due to an unknown root cause, leading to damage and possible loss of control of the airplane.
AD 2005-11-05 · published Jun 7, 2005, effective Jul 18, 2005
Precise Flight, Inc. Models SVS I and SVS IA Standby Vacuum Systems
The FAA adopts a new airworthiness directive (AD) for all airplanes equipped with Precise Flight, Inc. (Precise Flight) Models SVS I and SVS IA standby vacuum systems (SVS) installed under certain supplemental type certificates or through field approval. This AD requires you to replace the airplane flight manual supplement (AFMS) in the airplane flight manual with the appropriate revision and install placards as defined in the AFMS, upgrade the Model SVS I or SVS IA SVS to the Model VI SVS, and add the instructions for continued airworthiness (ICA) to the maintenance schedule for the aircraft. This AD results from several reports of failed shuttle control valves of the standby vacuum system (SVS) and one report of an airplane crash with a fatality in which improper use of the SVS was a factor. We are issuing this AD to correct problems with the SVS before failure or malfunction during instrument flight rules (IFR) flight that can lead to pilot disorientation and loss of control of the aircraft.
AD 2005-12-06 · published Jun 14, 2005, effective Jul 19, 2005
Teledyne Continental Motors (Formerly Bendix) S-20, S-1200, D-2000, and D-3000 Series Magnetos
The FAA is superseding an existing airworthiness directive (AD) for Teledyne Continental Motors (TCM) (formerly Bendix) S-20, S- 1200, D-2000, and D-3000 series magnetos equipped with impulse coupling assemblies. That AD currently requires replacing riveted-impulse coupling assemblies and snap-ring coupling assemblies, which are worn beyond limits, with serviceable riveted-impulse coupling assemblies or snap-ring impulse coupling assemblies. This ad requires a reduced inspection interval for magnetos with riveted-impulse coupling assemblies installed on certain Lycoming engine models. This AD does not lower the inspection interval for magnetos with snap-ring impulse coupling assemblies. This AD also limits the applicability to certain Lycoming engine models. This AD results from data provided by the manufacturer that shows a need to reduce the inspection intervals for riveted-impulse coupling assemblies used on certain Lycoming engine models. We are issuing this AD to prevent failure of the magneto impulse coupling assembly and possible engine failure.
