28 Airworthiness Directives: 20 airplane, 5 rotorcraft, 2 engine, 1 propeller.
AD 2005-03-01 · published Feb 2, 2005, effective Mar 9, 2005
Boeing Model 747 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Boeing Model 747 series airplanes, that requires repetitive inspections of the nacelle strut-to-wing attachment structure, and repetitive overhaul of the diagonal brace and spring beam load paths, to maintain damage tolerance requirements and ensure long-term structural integrity; and follow-on and corrective actions if necessary. This action is necessary to ensure the structural integrity of the strut-to-wing load path and prevent separation of the strut and engine from the airplane. This action is intended to address the identified unsafe condition.
AD 2005-03-02 · published Feb 2, 2005, effective Mar 9, 2005
Boeing Model 737-300, -400, and -500 Series Airplanes; and Model 757-200 and -200CB Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 737-300, -400, and -500 series airplanes; and Model 757-200 and -200CB series airplanes, that requires inspection of the applicable body station frames for open body station frames and related investigative/corrective actions; and installation of lanyard hook brackets and lanyard assemblies under the air conditioning overhead ducts, as applicable. This action is necessary to prevent loosened or disconnected overhead ducts from causing ceiling panels to drop below the minimum height of the evacuation zone for the passenger cabin, which could result in inadequate height for safe exit in the event of an emergency evacuation. This action is intended to address the identified unsafe condition.
AD 2005-03-04 · published Feb 2, 2005, effective Mar 21, 2005
Pacific Aerospace Corporation, Ltd. Model 750XL Airplanes
The FAA adopts a new airworthiness directive (AD) for all Pacific Aerospace Corporation, Ltd. (Pacific Aerospace) Model 750XL airplanes. This AD requires you to replace any type TLP-D or TLED rivets on the aileron pushrod ends and elevator control pushrod ends. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for New Zealand. We are issuing this AD to replace the above identified rivets on the aileron pushrod ends and elevator control pushrod ends, which, if not replaced, could result in loose mechanical elements in the control systems. This could lead to control anomalies and loss of airplane control.
AD 2005-03-03 · published Feb 4, 2005, effective Mar 11, 2005
Boeing Model 767-200, -300, and -300F Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to all Boeing Model 767-200, -300, and -300F series airplanes. That AD currently requires examination of maintenance records to determine if Titanine JC5A (also known as Desoto 823E508) corrosion inhibiting compound ("C.I.C.") was ever used; inspection for cracks or corrosion and corrective action, if applicable; repetitive inspections and C.I.C. applications; and modification of the aft trunnion area of the outer cylinder, which terminates the need for the repetitive inspections and C.I.C. applications. This new AD also requires, for certain other airplanes, repetitive inspections for cracks or corrosion, corrective action if necessary, and repetitive C.I.C. applications. This AD is prompted by a report that JC5A was used on more airplanes during production than previously identified. We are issuing this AD to prevent severe corrosion in the main landing gear (MLG) outer cylinder at the aft trunnion, which could develop into stress corrosion cracking and consequent collapse of the MLG.
AD 2005-03-05 · published Feb 4, 2005, effective Feb 22, 2005
McDonnell Douglas Model MD-90-30 Airplanes
The FAA is revising an existing airworthiness directive (AD), which applies to certain McDonnell Douglas Model MD-90-30 airplanes. This AD requires a one-time general visual inspection to detect wire chafing damage and to determine adequate clearance between the disconnect panel structure and the wires above the aft left lavatory; and corrective actions, if necessary. This new AD revises the applicability of the existing AD. This AD is prompted by the determination that certain airplanes unaffected by the existing AD are subject to the unsafe condition, and certain other airplanes should be removed from the applicability. We are issuing this AD to prevent damage to certain wires due to contact between the wires and the adjacent structure, which could result in electrical arcing and consequent smoke and fire in the cabin.
AD 2005-01-04 · published Feb 10, 2005, effective Feb 22, 2005
Raytheon Aircraft Company 90, 99, 100, 200, and 300 Series Airplanes
This document incorporates corrections to Airworthiness Directive (AD) 2005-01-04, which was published in the Federal Register on January 6, 2005 (70 FR 1169) with regulatory corrections published on January 27, 2005 (70 FR 3871). AD 2005-01-04 applies to certain Raytheon Aircraft Company 90, 99, 100, 200, and 300 series airplanes. This action incorporates the corrections into one document to help eliminate any confusion. We are re-issuing the AD in its entirety.
AD 2005-03-15 · published Feb 14, 2005, effective Mar 21, 2005
BAE Systems (Operations) Limited Model BAe 146 Series Airplanes and Model Avro 146-RJ Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain BAE Systems (Operations) Limited Model BAe 146 series airplanes and Model Avro 146-RJ series airplanes. This AD requires repetitive inspections to detect discrepancies of the fuselage skin and reinforcing plates along the wing to fuselage fairing access panels on the left- and right-hand sides of the airplane, and repair if necessary. This AD also provides for an optional terminating action for the repetitive inspections. This AD is prompted by a report of chafing on the wing to fuselage fairing panels. We are issuing this AD to prevent chafing of the fuselage skin and reinforcing plates, which could lead to reduced structural integrity of the airplane's fuselage.
AD 2005-03-16 · published Feb 14, 2005, effective Mar 21, 2005
Raytheon Model DH.125, HS.125, and BH.125 Series Airplanes; BAe.125 Series 800A (C-29A and U-125) and 800B Airplanes; and Hawker 800 (Including Variant U-125A) and 800XP Airplanes; Equipped with TFE731 Engines
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon Model DH.125, HS.125, and BH.125 series airplanes; BAe.125 series 800A (C-29A and U-125) and 800B airplanes; and Hawker 800 (including variant U-125A) and 800XP airplanes. This AD requires installing insulating blankets on the engine compartment firewall and the wire harness passing through the firewall fairlead. This AD is prompted by a report indicating that insulation on the wire harness passing through the firewall fairlead ignited on the fuselage side of the firewall. We are issuing this AD to prevent a fire in the engine compartment from causing possible ignition of outgassing wire insulation on the fuselage side of the firewall, which could lead to an uncontrollable fire in the fuselage.
AD 2005-03-13 · published Feb 16, 2005, effective Mar 23, 2005
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires doing repetitive inspections for fractures and cracks of the links of the aileron power control unit (PCU); replacing any fractured/cracked link; and doing applicable related investigative and corrective actions, if necessary. This AD is prompted by reports indicating that the links of the aileron PCU have failed. We are issuing this AD to prevent failure of both links of the aileron PCU, which could result in reduced lateral control of the airplane.
AD 2005-04-01 · published Feb 16, 2005, effective Mar 23, 2005
Boeing Model 707-100, -100B, -300, -300B (Including -320B Variant), -300C, and -E3A (Military) Series Airplanes; Model 720 and 720B Series Airplanes; Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes; and Model 747 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing transport category airplanes. This AD requires repetitive tests of the overwing fuel fill ports for certain wing tanks; an electrical bonding resistance test between the bulkhead fittings of the engine fuel feed tube and the front spar inside the fuel tank of the wings; other specified actions; and applicable corrective actions if necessary. This AD is prompted by our determination that this AD is necessary to reduce the potential for ignition sources inside fuel tanks. We are issuing this AD to prevent arcing or sparking at the interface between the bulkhead fittings of the engine fuel feed tube and the front spar inside the fuel tank of the wings and between the overwing fuel fill ports and the airplane structure during a lightning strike. Such arcing or sparking could provide a possible ignition source for the fuel vapor inside the fuel tank and cause consequent fuel tank explosions.
AD 2005-04-04 · published Feb 16, 2005, effective Mar 23, 2005
Saab Model SAAB SF340A and SAAB 340B Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Saab Model SAAB SF340A and SAAB 340B series airplanes. This AD requires a one-time inspection to determine the part and serial numbers of certain engine vibration isolators (mounts) and the cure dates of certain molded assemblies incorporated in those engine mounts; and related corrective actions if necessary. This AD is prompted by a report that disbonding of the elastomer from the inner metal core and shim of certain engine vibration mounts has occurred within a few hundred hours of operation, causing heavy chafing of the engine support system and chafing of the fire sensor loop. We are issuing this AD to prevent reduced integrity of the fire-shielding capacity of the nacelle structure and a possible fire detector fault.
AD 2005-04-06 · published Feb 16, 2005, effective Feb 23, 2005
Gulfstream Model GV-SP Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Model GV-SP series airplanes. This AD requires repetitive inspections of the avionics standard communication bus (ASCB) for any noise interference and repair of the ASCB if noise interference is found. This AD also requires revisions of the airplane flight manual (AFM) to prohibit dispatch of any flight with the integrated standby flight display (SFD) inoperative; to add procedures to facilitate recovery of the cockpit display units in the event that the cockpit displays go blank; and to add flightcrew briefings on the use of standby instruments in case the cockpit display units go blank and do not recover. This AD also requires installing an avionics software update and a hardware upgrade to the Honeywell Primus Epic system to correct a display blanking problem; installing the update will allow removal of certain AFM revisions and will end the repetitive inspections of the ASCB. This AD is prompted by a report indicating that all four cockpit flight panel displays went blank simultaneously. We are issuing this AD to prevent a software error from blanking the cockpit display units, which will result in a reduction of the flightcrew's situational awareness, and possible loss of control of the airplane. We are also issuing this AD to address noise interference in the ASCB, which can interfere with the display recovery after a blanking event and consequently extend the time that the displays remain blank. In addition, we are issuing this AD to ensure that the flightcrew is advised of the procedures necessary to address blank cockpit display units.
AD 2005-04-05 · published Feb 17, 2005, effective Mar 24, 2005
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 and -145 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain EMBRAER Model EMB-135 and -145 series airplanes. This AD requires repetitive detailed inspections of the oil in the air turbine starter (ATS) to determine the quantity of the oil and the amount of debris contamination in the oil. If the oil quantity is incorrect or if excessive debris is found in the oil, this AD requires replacement of the ATS with a new or serviceable ATS, and continued repetitive detailed inspections. This AD also requires eventual replacement of each ATS with a new, improved ATS, which constitutes terminating action for the repetitive detailed inspections. This action is necessary to prevent a flash fire in the nacelle, which would result in the flightcrew shutting down the engine during flight, and consequent reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
AD 2005-04-07 · published Feb 17, 2005, effective Feb 22, 2005
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes and Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604) Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes and Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604) series airplanes. This AD requires revising the airplane flight manuals to include a new cold weather operations limitation. This AD is prompted by a report that even small amounts of frost, ice, snow, or slush on the wing leading edges or forward upper wing surfaces can cause an adverse change in the stall speeds, stall characteristics, and the protection provided by the stall protection system. We are issuing this AD to prevent possible loss of control on take-off resulting from even small amounts of frost, ice, snow, or slush on the wing leading edges or forward upper wing surfaces.
AD 2005-04-02 · published Feb 18, 2005, effective Mar 25, 2005
Dassault Model Falcon 10 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Dassault Model Falcon 10 series airplanes. This AD requires a temporary change to the airplane flight manual (AFM) to provide procedures to the flightcrew for touchdown using the main landing gear to avoid a three- point landing. This AD also requires repetitive inspections of the piston rod of the drag strut actuator of the nose landing gear (NLG) for cracks, which would terminate the AFM revision, and corrective actions if necessary. In addition, this AD provides for a terminating modification, which would end the repetitive inspections. This AD is prompted by reports of failure of the piston rod of the drag strut actuator of the NLG. The cause of such failure has been attributed to fatigue cracking caused by corrosion in the piston rod of the drag strut actuator. We are issuing this AD to prevent cracking and/or fracture of the piston rod of the drag strut actuator of the NLG, which could result in a gear-up landing, structural damage, and possible injury to passengers and crew.
AD 2005-04-03 · published Feb 18, 2005, effective Mar 25, 2005
Boeing Model 747-400, -400D, and -400F Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-400, -400D, and -400F series airplanes. This AD requires replacing at least one flap control unit (FCU) in the main equipment center with a new or modified FCU. This AD is prompted by a report indicating that, after takeoff, an airplane was required to return to the airport because the autopilot disengaged. The report also indicated that, after selecting flaps for landing, the flaps indication display did not indicate the flap setting, requiring the airplane to land in alternate flap mode. We are issuing this AD to prevent disconnection of autoland/autopilot functions and loss of primary flaps control and flaps indication display due to disengagement of all three FCUs at the same time, which could lead to a non-normal high speed landing with the flaps retracted, increased pilot workload, and possible runway departure at high speeds during landing.
AD 2005-04-12 · published Feb 25, 2005, effective Apr 1, 2005
Saab Model SAAB SF340A and SAAB 340B Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Saab Model SAAB SF340A and SAAB 340B series airplanes. This AD requires repetitive inspections for wear of the brushes and leads and for loose rivets of the direct current (DC) starter generator, and related investigative/corrective actions if necessary. This AD is prompted by reports of premature failures of the DC starter generator prior to scheduled overhaul. We are issuing this AD to prevent failure of the starter generator, which could cause a low voltage situation in flight and result in increased pilot workload and reduced redundancy of the electrical powered systems.
AD 2005-04-13 · published Feb 25, 2005, effective Mar 14, 2005
Short Brothers Model SD3-60 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Short Brothers Model SD3-60 series airplanes. This AD requires, for certain airplanes, repetitive inspections for cracking of the balance weight brackets of the elevator trim tabs, and replacement of any cracked bracket with a new or reworked bracket that conforms to the approved design standard. This AD also provides for an optional terminating action for the repetitive inspections. This AD is prompted by reports indicating that balance weight brackets have been found cracked on both the left and right elevator trim tabs. We are issuing this AD to prevent failure of the balance weight bracket for the elevator trim tab, which could cause loss of the balance weight. This could result in incorrect trim during takeoff and landing, and reduced controllability of the airplane.
AD 2005-04-14 · published Feb 28, 2005, effective Mar 15, 2005
Boeing Model 757-200, 757-200CB, and 757-200PF Series Airplanes Equipped With Rolls Royce Model RB211 Engines
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Boeing Model 757-200, 757-200CB, and 757- 200PF series airplanes. The existing AD currently requires repetitive detailed inspections to detect horizontal or vertical movement of the shims at the joint of the mid-bulkhead and the upper link fittings, and corrective action if necessary; or certain alternative actions that terminate the requirement for the repetitive inspections. This new AD continues to require those repetitive inspections; decreases the allowable tolerance for shim migration; and adds new repetitive detailed inspections for cracking of the entire mid-bulkhead, and repair if necessary. This new AD also adds additional airplanes to the applicability of the AD. This AD is prompted by reports of cracks in the mid-bulkhead lower vertical flange common to the lower chord and stiffener and reports of cracking at other locations on the mid- bulkhead. We are issuing this AD to detect and correct migration of shims at the joint of the mid-bulkhead and the upper link fittings and cracking of the mid-bulkhead, which could result in cracking of the strut and consequent loss of the strut and engine.
AD 2005-03-07 · published Feb 10, 2005, effective Mar 17, 2005
Bell Helicopter Textron Canada Model 407 Helicopters
This amendment adopts a new airworthiness directive (AD) for Bell Helicopter Textron Canada (Bell) Model 407 helicopters that requires creating a component history card or equivalent record for each crosstube assembly, converting accumulated run-on landings to an accumulated Retirement Index Number (RIN) count, and establishing a maximum accumulated RIN for certain crosstube assemblies. This amendment is prompted by fatigue testing, analysis, and evaluation by the manufacturer that determined that run-on landings impose a high stress on landing gear or crosstubes and may cause cracking in the area above the skid tube saddle. The actions specified by this AD are intended to prevent fatigue failure in a crosstube assembly due to excessive stress during run-on landings and subsequent loss of control of the helicopter.
AD 2005-03-10 · published Feb 11, 2005, effective Mar 18, 2005
Bell Helicopter Textron, A Division of Textron Canada Helicopters
This amendment supersedes an existing airworthiness directive (AD) for Bell Helicopter Textron, A Division of Textron Canada (BHTC) Model 222, 222B, 222U, and 230 helicopters, that currently requires a visual check of each main rotor grip (grip) and pitch horn assembly without disassembling the main rotor hub assembly (hub assembly), and a visual inspection at specified intervals of each affected grip and pitch horn assembly for a crack using a 10-power or higher magnifying glass. If a crack is found, the existing AD requires replacing each unairworthy grip or pitch horn with an airworthy part before further flight. This amendment requires those same actions, and also requires an additional inspection of the grip and pitch horn assembly for a crack in the disassembled hub assembly, and replacing any cracked part with an airworthy part. This amendment is prompted by the determination that an additional enhanced inspection is needed to ensure the integrity of the hub assembly. The actions specified by this AD are intended to prevent failure of the grip or pitch horn and subsequent loss of control of the helicopter.
AD 2005-03-08 · published Feb 14, 2005, effective Mar 21, 2005
Eurocopter France Model AS350B, BA, B1, B2, B3, C, D, D1, and EC130 B4 Helicopters
This amendment adopts a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS350B, BA, B1, B2, B3, C, D, D1, and EC130 B4 helicopters that requires removing and modifying the fuel bleed lever. This amendment is prompted by some cases of loss of the fuel bleed lever in flight. If the tension of the control cable is too low, the cable may vibrate out of its notch, resulting in the fuel bleed lever separating from the hinge. The actions specified by this AD are intended to prevent a fuel bleed lever from separating and striking the tail rotor blade (blade), resulting in damage to or loss of a blade, and subsequent vibration and loss of control of the helicopter.
AD 2005-03-09 · published Feb 14, 2005, effective Mar 1, 2005
Eurocopter France Model EC 155B, EC155B1, SA-360C, SA-365C, SA-365C1, SA-365C2, SA-365N, SA-365N1, AS-365N2, AS 365 N3, and SA-366G1 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Eurocopter France (Eurocopter) model helicopters. This action requires an initial and repetitive borescope inspection of the main gearbox (MGB) planet gear carrier or an initial and repetitive visual inspection of the MGB planet gear carrier for a crack. Replacing any MGB that has a cracked planet gear carrier is required before further flight. This amendment is prompted by the discovery of cracks in the web of the planet gear carrier. The actions specified in this AD are intended to detect a crack in the web of the planet gear carrier, which could lead to a MGB seizure and subsequent loss of control of the helicopter.
AD 2005-04-09 · published Feb 17, 2005, effective Mar 4, 2005
Bell Helicopter Textron Canada Model 222, 222B, 222U, 230, and 430 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters that currently requires certain checks and inspections of the tail rotor blades. If a crack is found, the existing AD requires replacing the tail rotor blade (blade) with an airworthy blade before further flight. This amendment requires the same checks and inspections as the existing AD, but expands the applicability with the addition of two BHTC Model 430 helicopter serial numbers. This amendment is prompted by the manufacturer issuing revised service information that includes the additional two serial numbers. The actions specified by this AD are intended to detect a crack in the blade, and to prevent loss of a blade and subsequent loss of control of the helicopter.
AD 2005-03-06 · published Feb 10, 2005, effective Mar 17, 2005
Rolls-Royce Deutschland Ltd. & Co KG (formerly Rolls-Royce plc), Model Tay 611-8, 620-15, 650-15, and 651-54 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Rolls-Royce Deutschland Ltd. & Co KG (RRD) (formerly Rolls- Royce plc) Model Tay 611-8, 620-15, 650-15, and 651-54 turbofan engines, with low pressure (LP) fuel tube, part number (P/N) JR33021A, installed. That AD currently requires initial and repetitive inspections of the LP fuel tubes. This AD requires the same inspections and adds a requirement to replace the fuel tube with a new design tube, as mandatory terminating action to the repetitive inspections. This AD results from the manufacturer introducing a new design fuel tube, which eliminates the unsafe condition. We are issuing this AD to prevent a dual-engine flameout due to fuel exhaustion, which could lead to forced landing and possible damage to the airplane.
AD 2005-04-10 · published Feb 22, 2005, effective Mar 29, 2005
General Electric Company CT58 Series and Surplus Military T58 Series Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CT58-140-1, CT58-140-2, and surplus military T58-GE-5, -10, -100, and -402 turboshaft engines with certain serial numbers (SNs) of stage 1 compressor disks, part number (P/N) 5001T20P01, installed. This AD requires removing certain stage 1 compressor disks from service before reaching a reduced low-cycle- fatigue (LCF) life limit for those affected disks of 2,100 hours time- since-new (TSN) or by December 31, 2008, whichever occurs first. This AD results from two reports of low blade tip clearances in the compressor. We are issuing this AD to prevent LCF cracking and failure of the stage 1 compressor disk, an uncontained engine failure, and damage to the helicopter.
AD 2005-04-08 · published Feb 22, 2005, effective Mar 29, 2005
Hartzell Propeller Inc. Model HC-B3TN-5( )/T10282( ) Propellers
The FAA is superseding an existing Priority Letter Airworthiness Directive (AD) for Hartzell Propeller Inc. model HC-B3TN- 5( )/T10282( ) propellers. That AD currently requires initial and repetitive inspections of the blade pilot tube bore area. This ad requires the same inspections. This AD results from a review of all currently effective ADs. That review determined that Priority Letter AD 88-24-15 was not published in the Federal Register to make it effective to all operators, as opposed to just the operators who received actual notice of the original Priority Letter AD. This AD also results from the discovery that the original AD omitted an airplane model with a certain Supplemental Type Certificate (STC) from the applicability. We are issuing this AD to prevent possible blade failure near the hub which can result in blade separation, engine separation, damage to the airplane, and possible loss of the airplane.
