30 Airworthiness Directives: 18 airplane, 3 rotorcraft, 3 engine, 1 propeller, 2 appliance, 2 glider, 1 various.
AD 2004-19-11 · published Oct 1, 2004, effective Nov 5, 2004
Airbus Model A320 Series Airplanes
This amendment supersedes an existing airworthiness directive (AD), applicable to certain Airbus Model A320 series airplanes, that currently requires modification of the rear spar web of the wing, cold expansion of certain attachment holes for the forward pintle fitting and certain holes at the actuating cylinder anchorage of the main landing gear (MLG), repetitive inspections for fatigue cracking in certain areas of the rear spar of the wing, and corrective action if necessary. That AD also provides for optional terminating action for the requirements of the AD. This amendment revises certain compliance times for the inspection. The actions specified by this AD are intended to detect and correct fatigue cracking, which may lead to reduced structural integrity of the wing and the MLG. This action is intended to address the identified unsafe condition.
AD 2004-20-09 · published Oct 6, 2004, effective Oct 21, 2004
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires repetitive inspections for cracks, sealant damage, and corrosion of the main fittings of the main landing gear (MLG), and corrective actions if necessary. This AD is prompted by a report of a cracked main fitting of the MLG. We are issuing this AD to detect and correct fatigue cracking of the main fitting of the MLG and consequent failure of the main fitting, which could result in the collapse of the MLG.
AD 2004-20-11 · published Oct 13, 2004, effective Nov 17, 2004
Airbus Model A300 B2 and B4 Series Airplanes; and Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes (Collectively Called A300-600)
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A300 B2 and B4 series airplanes; and certain Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes; and Model C4-605R Variant F airplanes (collectively called A300-600). This AD requires an inspection of the skin panels of the wing slats for damage and certain repairs, and applicable related investigative/corrective actions if necessary. This AD is prompted by the results of an engineering evaluation that revealed that several repairs and some allowable damage limits specified in the structural repair manuals do not provide adequate static and/or fatigue strength for repaired wing slats. We are issuing this AD to find and fix previously done repairs of the wing slats that have inadequate static and/or fatigue strength, which, if not corrected, could result in loss of the slats and consequent reduced controllability of the airplane.
AD 2004-20-12 · published Oct 13, 2004, effective Nov 17, 2004
Airbus Model A300 B2 and B4 Series Airplanes; Model A300 B4-600, A300 B4-600R, A300 F4-600R Series Airplanes, and A300 C4-605R Variant F Airplanes (Collectively Called A300-600); and Model A310 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Airbus Model A300 B2 and B4 series airplanes; Model A300 B4-600, A300 B4-600R, A300 F4-600R series airplanes, and A300 C4- 605R Variant F airplanes (collectively called A300-600); and Model A310 series airplanes. This amendment requires a detailed inspection of certain pulleys and control cables in the rear fuselage for corrosion and damage; and corrective action, if necessary. This action is necessary to detect and correct frayed or corroded control cables for the elevator and rudder, which could result in a ruptured control cable, and possible reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
AD 2004-20-13 · published Oct 13, 2004, effective Nov 17, 2004
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 and EMB-145 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain EMBRAER Model EMB-135 and EMB-145 series airplanes, that requires inspection of the housings of the main landing gear (MLG) leg strut bushings, and related investigative and corrective actions, and other specified actions. The actions specified by this AD are intended to prevent corrosion of the housings of the MLG leg strut bushings and consequent failure of the MLG. This action is intended to address the identified unsafe condition.
AD 2004-20-14 · published Oct 13, 2004, effective Nov 17, 2004
Airbus Model A300 B4 Series Airplanes and Model A300 B4-600, A300 B4-600R, and A300 F4-600R (Collectively Called A300-600) Series Airplanes
This amendment supersedes an existing airworthiness directive (AD), applicable to all Airbus Model A300 B4 series airplanes and all Airbus Model A300-600 series airplanes. That AD currently requires a one-time high frequency eddy current inspection to detect cracking of the splice fitting at fuselage frame (FR) 47 between stringers 24 and 25; and corrective actions if necessary. This amendment requires new repetitive inspections of an expanded area and adds airplanes to the applicability in the existing AD. The actions specified by this AD are intended to detect and correct cracking of the splice fitting at fuselage FR 47, which could result in reduced structural integrity of the airplane. This action is intended to address the identified unsafe condition.
AD 2004-20-15 · published Oct 13, 2004, effective Nov 17, 2004
Dornier Model 328-100 Series Airplanes
This amendment supersedes an existing airworthiness directive (AD), applicable to all Dornier Model 328-100 series airplanes, that currently requires certain revisions to the airplane flight manual, replacement of certain de-icing boots in the air intake duct assemblies of the engine with re-designed units, repetitive inspections of the boots to find discrepancies, and corrective action if necessary. This amendment also requires modification of the engine air inlet de-icing system. This action extends the repetitive inspection interval required by the existing AD, and adds repetitive debonding/delamination and leakage inspections of the de-icing boots, and corrective action if necessary. Initiation of the extended repetitive inspections and new repetitive inspections ends the repetitive inspections required by the existing AD. The actions specified by this AD are intended to prevent engine malfunction due to failure of the engine air inlet de-icing system, which could result in reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
AD 2004-20-16 · published Oct 13, 2004, effective Nov 17, 2004
Boeing Model 747-200B, -200C, -200F, -300, -400, -400D, and -400F Series Airplanes; and Model 747SP Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 747-200B, -200C, -200F, -300, -400, -400D, and -400F series airplanes; and Model 747SP series airplanes, that requires repetitive functional tests of the auxiliary power unit (APU) and engine fire shutoff switches and repetitive replacements of the APU and engine fire shutoff switches. The AD also provides an optional terminating action for the repetitive functional tests and replacements. This action is necessary to prevent mineral build-up on the APU and engine fire shutoff switches, which could lead to failure of the switches to discharge fire suppressant in the affected area and could result in an uncontrolled fire that could spread to the strut, wing, or aft body of the airplane. This action is intended to address the identified unsafe condition.
AD 2004-21-03 · published Oct 18, 2004, effective Nov 2, 2004
Gulfstream Model G-1159, G-1159A, G-1159B, and G-IV Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Gulfstream Model G-1159, G-1159A, G-1159B, and G-IV series airplanes. This AD requires a one-time inspection of the left and right aileron and elevator actuators to determine the part and serial numbers of each actuator, repetitive inspections of suspect actuators to detect broken damper shafts, and replacement of any actuator having a broken damper shaft. This AD also requires that operators report any broken damper shaft they find to the FAA. This AD also provides an optional terminating action for the repetitive inspection requirements of this AD. This AD is prompted by reports of broken or cracked damper shafts within the aileron and elevator actuator assemblies. We are issuing this AD to detect and correct broken damper shafts, which could result in locking of an aileron or elevator actuator (hard-over condition), subsequent loss of aileron or elevator control, and consequent reduced controllability of the airplane.
AD 2004-21-06 · published Oct 21, 2004, effective Dec 6, 2004
deHavilland Inc. Models DHC-2 Mk. I and DHC-2 Mk. II Airplanes and Bombardier Inc. Model (Otter) DHC-3 Airplanes
The FAA adopts a new airworthiness directive (AD) for all deHavilland Inc. Models DHC-2 Mk. I and DHC-2 Mk. II airplanes and for all Bombardier Inc. Model (Otter) DHC-3 airplanes powered by radial engines. This AD requires you to visually inspect the firewall connector plugs for proper lockwire security and replace or modify as appropriate. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Canada. We are issuing this AD to prevent loss of ignition systems during flight caused by improper lockwire security, which could result in engine failure. This failure could lead to a forced landing of the airplane.
AD 2004-19-10 · published Oct 26, 2004, effective Nov 1, 2004
Boeing Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes
This document corrects a typographical error that appeared in airworthiness directive (AD) 2004-19-10 that was published in the Federal Register on September 27, 2004 (69 FR 57632). The typographical error resulted in the omission of the AD number in one location of the document. This AD is applicable to certain Boeing Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD requires repetitive inspections for corrosion and cracking of the pivot hinge pins of the horizontal stabilizer, certain follow-on inspections, and replacement of the hinge pins with new or serviceable pins if necessary.
AD 2004-21-08 · published Oct 26, 2004, effective Nov 30, 2004
Cessna Aircraft Company Models 190, 195 (L-126A,B,C), 195A, and 195B Airplanes
The FAA adopts a new airworthiness directive (AD) for all Cessna Aircraft Company (Cessna) Models 190, 195 (L-126A,B,C), 195A, and 195B airplanes that are equipped with certain inboard aileron hinge brackets. This AD requires you to repetitively inspect the affected inboard aileron hinge brackets for cracks or corrosion and replace them if found cracked or corroded. Replacement with aluminum brackets would terminate the need for the repetitive inspections. This AD results from several reports of cracks and corrosion found on the magnesium aileron hinge brackets. Magnesium is known to be susceptible to corrosion. We are issuing this AD to detect and correct corrosion damage to the inboard aileron hinge brackets. Such damage could result in the brackets cracking across the bearing boss and could lead to the aileron separating from the airplane with consequent reduced or loss of control of the airplane.
AD 2004-22-02 · published Oct 27, 2004, effective Dec 1, 2004
Raytheon (Beech) Model MU-300-10, 400, 400A, and 400T Series Airplanes; and Raytheon (Mitsubishi) Model Beech MU-300 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon (Beech) Model MU-300-10, 400, 400A, and 400T series airplanes; and certain Raytheon (Mitsubishi) Model Beech MU-300 airplanes. This AD requires a one-time inspection of certain panels in the spoiler mixer bay for the presence of drain holes, and the addition of at least one new drain hole; and a one-time inspection for discrepancies of the sealant on the relief cutout on the aft pressure bulkhead, and on certain baffles; and corrective actions if necessary. This AD is prompted by a report of fuel leaking from components in the spoiler mixer bay of several Raytheon (Beech) Model 400A series airplanes. We are issuing this AD to prevent the accumulation of fuel and/or fuel vapor in the spoiler mixer bay and/or the aft fuselage compartment, which could result in a fire in the airplane.
AD 2004-22-05 · published Oct 27, 2004, effective Nov 12, 2004
Boeing Model 737-300, -400, and -500 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 737-300, -400, and -500 series airplanes. This AD requires inspecting for discrepancies of the fuselage skin under the dorsal fin assembly, and repairing if necessary. This AD is prompted by a report of an 18-inch crack found in the fuselage skin area under the blade seals of the nose cap of the dorsal fin due to previous wear damage. We are issuing this AD to find and fix discrepancies of the fuselage skin, which could result in fatigue cracking due to cabin pressurization, and consequent rapid in-flight decompression of the airplane fuselage.
AD 2004-22-04 · published Oct 28, 2004, effective Dec 2, 2004
Boeing Model 747-400, -400D, and -400F Series Airplanes Equipped With General Electric (GE) or Pratt & Whitney (P&W) Series Engines
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 747-400, -400D, and -400F series airplanes, equipped with GE or P&W series engines. This amendment requires modifications and functional tests of the wiring of the wire integration unit and the air supply control test unit (ASCTU) of the engine bleed air distribution system. The actions specified by this AD are intended to prevent inadvertent commanded shutdown of the engine bleed air distribution systems due to an erroneous ASCTU command. This type of shutdown could cause depressurization of the airplane and subsequent ice build-up on the engine inlets during descent, which could result in ingestion of ice into the engine(s) and consequent loss of thrust on one or more engines. This action is intended to address the identified unsafe condition.
AD 2004-22-06 · published Oct 28, 2004, effective Dec 2, 2004
Dornier Model 328-100 and -300 Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Dornier Model 328-100 and -300 series airplanes, that requires inspection of the metal oxide varistor (MOV) modules and transient absorption zener (TAZ) diodes to determine if those parts are outside of tolerance limits, and replacement of MOV modules and TAZ diodes with new parts, if necessary. This action is necessary to prevent the failure of critical ice protection systems following a lightning strike, which could result in reduced controllability and degraded performance of the airplane in the event of an encounter with icing conditions. This action is intended to address the identified unsafe condition.
AD 2004-22-08 · published Oct 28, 2004, effective Dec 2, 2004
Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to all Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, that requires repetitive inspections of the check valves and air supply ducts of the rear bulkhead for damage, and related corrective actions. This amendment also would require eventual rework or replacement of the air supply ducts, which would terminate the repetitive inspections for the air supply ducts only. This action is necessary to prevent disconnection of an air supply duct, which, if combined with failure of a bulkhead check valve, could result in rapid depressurization of the airplane. This action is intended to address the identified unsafe condition.
AD 2004-22-03 · published Oct 29, 2004, effective Dec 3, 2004
Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 and -145 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model EMB-135 and -145 series airplanes. This AD requires measuring the fillet radius dimension of the trunnion fitting webs of the wings; and reworking the fillet radius of the trunnion fitting web in order to increase the radius, doing related investigative actions, and doing applicable corrective action, if necessary. This AD is prompted by a report indicating that trunnion fittings of the wings have been manufactured with a web fillet radius smaller than the minimum required by the design data, which may induce the occurrence of fatigue cracks at the root of the trunnion fillet radius and adjacent structures (e.g., spar and ribs). We are issuing this AD to detect and correct fatigue cracking of the wing trunnion fittings or adjacent structure, which could result in failure of the main landing gear, consequent damage to surrounding structure, and possible loss of control of the airplane during landing.
AD 2004-20-07 · published Oct 5, 2004, effective Nov 9, 2004
Bell Helicopter Textron Canada Model 222, 222B, 222U, and 230 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (BHTC) model helicopters that requires certain inspections of the main rotor yoke (yoke) for a crack, fretting, or buffer deterioration. If a crack is found, the AD requires replacing the yoke with an airworthy yoke before further flight. If fretting or buffer deterioration are found, the AD requires further inspecting the main rotor hub assembly (hub assembly) and repairing or replacing any unairworthy parts. Also, the AD requires a torque inspection of the flapping bearing retaining nuts at specified intervals. This amendment is prompted by the discovery of a crack in a yoke. The actions specified by this AD are intended to prevent failure of the yoke and subsequent loss of control of the helicopter.
AD 2004-20-08 · published Oct 6, 2004, effective Oct 21, 2004
MD Helicopters, Inc. (MDHI) Model 500N and 600N Helicopters
This amendment adopts a new airworthiness directive (AD) for MD Helicopters, Inc. (MDHI) Model 500N and 600N helicopters. This action requires using a bright light and a 10x or higher magnifying glass to inspect each forward and center thruster control cable assembly connector (connector) for corrosion pitting or cracking. If you find corrosion pitting or cracking, this AD also requires replacing the cable assembly with an airworthy cable assembly before further flight. This amendment is prompted by a report of a failure of the forward thruster cable assembly due to stress corrosion. The actions specified in this AD are intended to detect a corrosion-pitted or cracked connector and prevent failure of the cable assembly and subsequent loss of control of the helicopter.
AD 2004-22-12 · published Oct 29, 2004, effective Dec 3, 2004
MD Helicopters, Inc. Model 600N Helicopters
This amendment adopts a new airworthiness directive (AD) for MD Helicopters, Inc. Model 600N helicopters that requires replacing the fuselage Station 75 control support bracket assembly (control support bracket), reducing the life limit, and revising the Limitations section of the applicable maintenance manual to state the reduced life limits on certain serial-numbered helicopters. This amendment is prompted by information received from the manufacturer indicating that the fatigue life of the control support bracket is shorter than the original analysis indicated. The actions specified by this AD are intended to prevent failure of the control support bracket and subsequent loss of control of the helicopter.
AD 2004-20-01 · published Oct 1, 2004, effective Nov 5, 2004
Pratt & Whitney Canada Models PW123, PW123B, PW123C, PW123D, PW123E, PW123AF, PW124B, PW125B, PW126A, PW127, PW127E, PW127F, and PW127G Turboprop Engines
The FAA is adopting a new airworthiness directive (AD) for Pratt & Whitney Canada (PWC) models PW123, PW123B, PW123C, PW123D, PW123E, PW123AF, PW124B, PW125B, PW126A, PW127, PW127E, PW127F, and PW127G turboprop engines. This AD requires initial and repetitive gap inspections of the bypass valve cover, on certain part number (P/N) mechanical fuel controls (MFCs), and replacement of those MFCs as mandatory terminating action to the repetitive inspections. This AD is prompted by sixteen reports of loss of engine throttle response and overspeed, eight of which resulted in in-flight shutdown. We are issuing this AD to prevent loss of throttle response and overspeed, resulting in engine in-flight shutdown.
AD 2004-20-04 · published Oct 1, 2004, effective Oct 18, 2004
Pratt & Whitney Canada PT6B-36A and PT6B-36B Turboshaft Engines
The FAA is adopting a new airworthiness directive (AD) for Pratt & Whitney Canada (PWC) PT6B-36A and PT6B-36B turboshaft engines with compressor rear hubs, part number (P/N) 3018111 installed. This AD requires reviewing, and correcting if necessary the critical part record for compressor rear hubs, P/N 3018111. This AD also requires removing compressor rear hubs from service that exceed the published part life limit, before further flight. This AD results from the discovery of a compressor rear hub, P/N 3018111, that exceeded the published life limit. This occurred because the operator used an incorrect life limit calculation contained in a PWC Service Bulletin. We are issuing this AD to prevent uncontained failure of the compressor rear hub and damage to the airplane.
AD 2004-22-07 · published Oct 27, 2004, effective Dec 1, 2004
General Electric Company (GE) CF6-80C2 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for GE CF6-80C2 turbofan engines with certain part number (P/N) high pressure turbine stage 2 nozzle guide vanes (HPT S2 NGVs) installed. This AD requires flex borescope inspections of HPT S2 NGVs installed in CF6- 80C2 turbofan engines. This AD results from an uncontained engine failure due to HPT S2 NGV distress. We are issuing this AD to prevent blade separation from HPT S2 NGV distress, which could result in an uncontained engine failure.
AD 2004-21-01 · published Oct 14, 2004, effective Oct 19, 2004
Hartzell Propeller Inc. (formerly Hartzell Propeller Products Division) Model HC-B5MP-3( )/M10282A( )+6 Five Bladed Propellers
The FAA is superseding an existing AD for certain Hartzell Propeller Inc. (formerly Hartzell Propeller Products Division) Model HC-B5MP-3( )/M10282A( )+6 five bladed propellers. That AD currently requires initial and repetitive torque check inspections on the attach bolts on certain model Hartzell HC-B5MP-3 five bladed propellers, and replacement of attach bolts if necessary. This AD requires the same inspections, but reduces compliance time for the initial inspection on certain Short Brothers Ltd. Model SD3-30 airplanes to before further flight and within 100 hours time-in-service for propellers installed on certain Aerospatiale (Nord) Model 262A airplanes. This AD also requires repetitive torque check inspections at reduced intervals on SD3-30 airplanes, and requires additional visual inspections of mounting flanges, and threads in hub bolt holes, and replacement of attach bolts and hubs, if necessary. This AD results from four reports in the last 12 months of eleven cracked or failed propeller attach bolts on Short Brothers Model SD3-30 airplanes. We are issuing this AD to prevent propeller separation from the airplane.
AD 2004-21-04 · published Oct 15, 2004, effective Nov 19, 2004
Becker Flugfunkwerk GmbH AR 4201 VHF AM Transceivers
The FAA is adopting a new airworthiness directive (AD) for certain Becker Flugfunkwerk GmbH AR 4201 VHF AM transceivers. This AD requires adding an aircraft flight manual (AFM) limitation to the Limitations Section of the AFM, and cockpit placard due to the intermittent malfunctioning of the transceiver, or removing the affected transceiver from service. This AD results from reports of crewmembers having difficulty communicating with Air Traffic Control and other aircraft due to the AR 4201 VHF AM transceiver's inability to block interference from transmitters operating on frequencies other than those set in the transceiver. We are issuing this AD to prevent difficulty in communicating with Air Traffic Control and other aircraft due to intermittent malfunctioning of the transceiver.
AD 2004-21-05 · published Oct 22, 2004, effective Nov 19, 2004
Kelly Aerospace Power Systems B-Series Combustion Heaters Models B1500, B2030, B2500, B3040, B3500, B4050, and B4500 (Formerly Owned by JanAero Devices, Janitrol, C&D, FL Aerospace, and Midland-Ross Corporation)
The FAA is superseding Airworthiness Directive (AD) 96-20-07, which applies to certain B-Series Combustion Heaters Models B1500, B2030, B3040, and B4050 that are installed on airplanes. AD 96-20-07 currently requires you to repetitively test (pressure decay) the combustion tube and overhaul any heater that does not pass any test. AD 96-20-07 also requires you to repetitively test the operation of the combustion air pressure switch and replace any combustion pressure switch that does not pass one of the tests. As a terminating action for the repetitive test requirements of AD 96-20-07, you could install a new ceramic-coated combustion tube and an improved design combustion air pressure switch. This AD is the result of reports that the new ceramic-coated combustion tubes are subject to the same distress as the non-ceramic coated combustion tubes. Consequently, this AD retains the repetitive testing requirements of AD 96-20-07, removes the terminating action for the combustion tube, and adds Models B2500, B3500, and B4500 to the applicability section. We are issuing this AD to prevent combustion by-products (carbon-monoxide exhaust) and fuel leakage from the combustion heaters caused by failure of the combustion heater system. This failure could result in fire or explosion in the airplane and possible carbon monoxide poisoning of the crew and passengers in the cabin.
AD 2004-20-10 · published Oct 14, 2004, effective Nov 24, 2004
Valentin GmbH & Co. Taifun 17E Sailplanes
The FAA adopts a new airworthiness directive (AD) for all Valentin GmbH & Co. Taifun 17E sailplanes. This AD requires you to do an operational check of the front wing-locking mechanism left and right, inspect stop key movement, inspect wing and fuselage side root ribs, inspect the wing side shear force fittings, and take any corrective actions that may be required. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this AD to detect and correct malfunction of wing-locking mechanism, which could result in failure of the wing-locking mechanism disengagement. This failure could lead to unlocking of wing in flight and consequent loss of control of the sailplane.
AD 2004-21-02 · published Oct 14, 2004, effective Nov 29, 2004
Przedsiebiorstwo Doswiadczalno-Produkcyjne Szybownictwa “PZL-Bielsko” Model SZD-50-3 “Puchacz” Sailplanes
The FAA adopts a new airworthiness directive (AD) for all Przedsiebiorstwo Doswiadczalno-Produkcyjne Szybownictwa "PZL-Bielsko" (PZL-Bielsko) Model SZD-50-3 "Puchacz" sailplanes. This AD requires you to repetitively inspect the front and back of the fuselage front bulkhead attachment fitting for cracks and replace the attachment fitting if any cracks are found. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Poland. We are issuing this AD to detect and correct cracks in the fuselage front bulkhead attachment fitting, which could result in structural failure of the bulkhead. This failure could lead to loss of control of the sailplane.
AD 2004-22-01 · published Oct 27, 2004, effective Dec 1, 2004
Various Transport Category Airplanes on Which Cargo Restraint Strap Assemblies Have Been Installed per Supplemental Type Certificate (STC) ST01004NY
This amendment adopts a new airworthiness directive (AD), applicable to various transport category airplanes on which cargo restraint strap assemblies have been installed per STC ST01004NY. This amendment requires revising the airplane flight manual to include a procedure for discontinuing the use of certain cargo restraint strap assemblies installed per STC ST01004NY, if used as the only cargo restraint. This amendment also requires revising the airplane weight and balance manual to include the same procedure described previously. The actions specified by this AD are intended to prevent shifting or unrestrained cargo in the cargo compartment, which could cause an unexpected change in the airplane's center of gravity, damage to the airplane structure and/or flight control system, a hazard to the flightcrew, and/or possible loss of controllability of the airplane. This action is intended to address the identified unsafe condition.
