15 Airworthiness Directives: 8 airplane, 3 rotorcraft, 2 engine, 1 appliance, 1 various.
AD 2003-22-08 · published Nov 3, 2003, effective Dec 8, 2003
McDonnell Douglas Model MD-11 and -11F Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain McDonnell Douglas Model MD-11 and -11F airplanes, that requires a one-time inspection of the barrel nut holes of the upper spar caps and skin panel of the horizontal stabilizer for corrosion, and follow-on and corrective actions if necessary. This action is necessary to prevent such corrosion, which could result in structural damage and consequent reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
AD 2003-22-12 · published Nov 7, 2003, effective Dec 12, 2003
Bombardier Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604) Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Bombardier Model CL-600-1A11 (CL-600), CL-600- 2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604) series airplanes. This amendment requires revising the airplane flight manual to provide the flightcrew with procedures and limitations for operating the airplane with out-of-tolerance angle of attack (AOA) transducers. This amendment also requires, among other actions, measuring the vane angles and voltage of the AOA transducers; reworking the AOA transducer assemblies; repetitive measurements of the resistance of both AOA transducers; and follow-on and corrective actions, as applicable. This action is necessary to prevent flat spots on the potentiometers of the AOA transducers due to wear, which may cause a delay in the commands for stall warning, stick shaker, and stick pusher operation. This action is intended to address the identified unsafe condition.
AD 2003-22-13 · published Nov 13, 2003, effective Dec 23, 2003
AeroSpace Technologies of Australia Pty Ltd. Models N22B and N24A Airplanes
The FAA adopts a new airworthiness directive (AD) for all AeroSpace Technologies of Australia Pty Ltd. (ASTA) Models N22B and N24A airplanes. This AD requires you to visually inspect the ailerons for damage and replace if necessary; adjust the engine power levers aural warning microswitches; set flap extension and flap down operation limitations; and fabricate and install cockpit flap extension and flap down operation restriction placards. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Australia. We are issuing this AD to prevent damage to the aileron due to airplane operation and pre-existing and undetected damage, which could result in failure of the aileron. Such failure could lead to reduced or loss of control of the airplane.
AD 2003-23-01 · published Nov 13, 2003, effective Dec 18, 2003
Boeing Model 747-400, -400D, and -400F Series Airplanes
This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 747-400, -400D, and -400F series airplanes, that requires reviewing airplane maintenance records; inspecting the yaw damper actuator portion of the upper and lower rudder power control modules (PCM) for cracking, and replacing the PCMs if necessary; and reporting airplane maintenance records review and inspection results to the manufacturer. This action is necessary to detect and correct cracking in the yaw damper actuator portion of the upper and lower rudder PCMs, which could result in an uncommanded left rudder hardover, consequent increased pilot workload, and possible runway departure upon landing. This action is intended to address the identified unsafe condition.
AD 2003-23-02 · published Nov 13, 2003, effective Nov 28, 2003
Cessna Model 560 Airplanes
This amendment adopts a new airworthiness directive (AD) that is applicable to certain Cessna Model 560 airplanes. This action requires disengaging and tie-strapping the pitch trim and autopilot servo (servo 1) circuit breakers. This action also provides an optional inspection and follow-on actions that, if accomplished, terminates the requirement to disengage and tie-strap those circuit breakers. This action is necessary to prevent a single-point failure in the trim system from causing a runaway trim condition that the pilot may be unable to stop by using the autopilot-disconnect switch. This condition could result in loss of control of the airplane. This action is intended to address the identified unsafe condition.
AD 2003-23-03 · published Nov 18, 2003, effective Dec 23, 2003
Boeing Model 737-100, -200, and -200C Series Airplanes
This amendment supersedes an existing airworthiness directive (AD), applicable to certain Boeing Model 737-100, -200, and -200C series airplanes, that currently requires repetitive inspections to detect discrepancies in the upper and lower skins of the fuselage lap joint, and repair if necessary. This amendment adds new inspections, reduces the repetitive inspection intervals for certain airplanes, and mandates a terminating modification. The actions specified by this AD are intended to detect and correct discrepancies in the upper and lower skins of the fuselage lap joint and circumferential joint, which could result in sudden fracture and failure of a lap joint or circumferential joint and rapid decompression of the airplane fuselage. This action is intended to address the identified unsafe condition.
AD 2003-23-04 · published Nov 18, 2003, effective Dec 23, 2003
Boeing Model 757-200 Series Airplanes
This amendment supersedes an existing airworthiness directive (AD), applicable to certain Boeing Model 757-200 series airplanes, that currently requires modification of the number 3 left and right emergency exit doors. This amendment requires a new, improved modification of the number 3 left and right emergency exit doors, which terminates the requirements in the existing AD. The actions specified by this AD are intended to prevent the number 3 emergency exit doors from jamming, which could impede the safe evacuation of passengers and crew during an emergency. This action is intended to address the identified unsafe condition.
AD 2003-24-03 · published Nov 26, 2003, effective Dec 31, 2003
Bombardier Model CL-600-2C10 (Regional Jet Series 700 & 701) Series Airplanes
This amendment supersedes an existing airworthiness directive (AD), applicable to certain Bombardier Model CL-600-2C10 (Regional Jet Series 700 & 701) series airplanes, that currently requires a revision to the Airplane Flight Manual (AFM) to prohibit operations into known or forecast icing conditions under certain conditions. That AD also requires an inspection to detect damage of the wing anti-ice (WAI) ducts to determine if the external shrouds of the ducts are open or cracked, and replacement of any damaged duct with a new duct or a duct with the same part number, and an optional terminating action. This amendment requires accomplishment of the previously optional terminating action for the AFM revision and inspection. The actions specified by this AD are intended to prevent the WAI ducts from collapsing, cracking, or rupturing, which could cause leakage of hot air in the under-floor pressurized area of the fuselage when the anti- ice system is turned on. Such leakage of hot air results in insufficient heat for the anti-ice system and consequent aerodynamic degradation. This action is intended to address the identified unsafe condition.
AD 2003-22-11 · published Nov 3, 2003, effective Dec 8, 2003
Eurocopter France Model AS350B, B1, B2, B3, BA, C, D, D1, and AS355E, F, F1, F2, and N Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Eurocopter France (Eurocopter) Model AS350B, B1, B2, B3, BA, D, and AS355E helicopters, that currently requires removing certain serial-numbered main servocontrols before further flight. This amendment contains the same requirements but also requires removing certain other main and tail servocontrols on or before 550 hours time- in-service (TIS) or 24 months, whichever occurs first. Also, this amendment adds the Eurocopter Model AS350C, D1, and AS355F, F1, F2, and N helicopters to the applicability. This amendment is prompted by the discovery of a manufacturing defect in another set of servocontrols. The actions specified by this AD are intended to prevent failure of a main or tail servocontrol in the flight control system and subsequent loss of control of the helicopter.
AD 2003-22-10 · published Nov 5, 2003, effective Dec 10, 2003
Eurocopter France Model EC120B Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Eurocopter France model helicopters that requires operators to either temporarily or permanently secure the electrical bonding braid (bonding braid) that is installed on the left cyclic pitch control stick base within 10 hours time-in-service (TIS) and, if temporarily secured, installing a permanent attachment system for the bonding braid within 500 hours TIS or 12 months, whichever occurs first. This amendment is prompted by a report of a bonding braid twisting around the attachment nut installed on the bolt that connects the roll channel torque link to the left-hand cyclic pitch control stick. The actions specified by this AD are intended to prevent an unsecured bonding braid from restricting travel to the cyclic pitch control stick, and subsequent loss of control of the helicopter.
AD 2003-24-01 · published Nov 25, 2003, effective Dec 10, 2003
MD Helicopters, Inc. Model 369A, H, HE, HM, HS, D, and E Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified model helicopters modified with a Helicopter Technology Company, LLC, Supplemental Type Certificate (STC) No. SR09172RC, SR09074RC, or SR09184RC. This action requires recording on the component history card or equivalent record the number of torque events (TEs) on each main rotor blade (blade). When a blade accumulates 13,720 TEs and 750 hours time-in-service (TIS), the AD requires inspecting both surfaces of the blade for a crack at specified intervals. If a crack is found, the AD also requires replacing the blade with an airworthy blade. Also, the AD establishes life limits for certain part- numbered blades. This proposal is prompted by several reports, including a recent report dated July 24, 2003, of blade cracks due to a high number of TEs per hour. The actions specified in this AD are intended to prevent fatigue cracking of the blade, blade failure, and subsequent loss of control of the helicopter.
AD 2003-22-09 · published Nov 3, 2003, effective Dec 3, 2003
Pratt & Whitney PW4074, PW4074D, PW4077, PW4077D, PW4084, PW4084D, PW4090, PW4090D, PW4090-3, and PW4098 Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for Pratt & Whitney PW4074, PW4074D, PW4077, PW4077D, PW4084, PW4084D, PW4090, PW4090D, PW4090-3, and PW4098 turbofan engines. This AD requires borescope inspection of the No. 3 bearing weep tube, on engines with high oil consumption that troubleshooting procedures fail to determine the source of oil loss. This AD also requires for all engines, initial and repetitive visual inspections of the turbine exhaust case (TEC) in the vicinity of the No 3 bearing oil vent tube for evidence of oil wetting or staining. If the vent tube borescope inspection is unsuccessful due to tube blockage, this AD also requires borescope inspections of the high pressure turbine (HPT) assembly for oil wetting or staining. This AD also requires removal of the HPT assembly and replacement of any heat distressed HPT assembly hardware if oil wetting or staining is found. This AD is prompted by reports of engine HPT assembly hardware being damaged as a result of thermal distress from oil igniting after leaking from the No. 3 bearing compartment. We are issuing this AD to prevent thermal distressed HPT assembly hardware from remaining in service, which could result in a cracked HPT stage 1 disk or HPT stage 1-2 air seal and an uncontained engine failure.
AD 2003-22-14 · published Nov 13, 2003, effective Dec 18, 2003
Rolls-Royce Deutschland Ltd & Co KG Models Tay 650-15 and 651-54 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Rolls-Royce Deutschland Ltd & Co KG (RRD) (formerly Rolls- Royce plc) models Tay 650-15 and 651-54 turbofan engines with certain part numbered fan blades and fan discs. That AD currently requires initial and repetitive visual and ultrasonic inspections of fan blades for cracks, and, if necessary, replacement with serviceable parts. In addition, that AD requires recording instances when engines are operated in a stabilized manner in newly prohibited ranges. This ad has the same requirements. In addition, this AD requires recording instances when engines are operated inadvertently in reverse thrust in prohibited ranges, and requires before further flight, initial and repetitive ultrasonic inspections of fan blades for cracks and if necessary, dispositioning of fan blades and fan discs, if certain reverse thrust events occurred. This AD is prompted by updated prohibited ranges of engine operation and the introduction of an N1 Alert System in Fokker Model F.28 Mark 0100 airplanes with Tay 650-15 engines installed. We are issuing this AD to prevent fan blade failures, which can result in an uncontained engine failure, engine fire, and damage to the airplane.
AD 2003-23-05 · published Nov 19, 2003, effective Dec 24, 2003
Titeflex Corporation
The FAA is adopting a new airworthiness directive (AD) for certain Titeflex Corporation hoses installed on Boeing 737-300, -400, - 500, -600, -700, -700C, -800, -900, 747-400, 757-200, -300, 767-200, - 300, and -300F airplanes. This AD requires, within 24 months after the effective date of the AD, inspection of certain Titeflex Corporation hoses for proper date and paint code, replacement if necessary, and inspection for proper heat treatment of aluminum B-nuts, if necessary. This AD is prompted by certain Titeflex Corporation hoses discovered with incorrect heat treatment of B-nuts. We are issuing this AD to prevent fire extinguishing system and fuel system hose failure due to improperly heat treated aluminum B-nuts.
AD 2003-03-15 R1 · published Nov 17, 2003, effective Dec 22, 2003
Various Boeing and McDonnell Douglas Transport Category Airplanes
This amendment revises an existing airworthiness directive (AD), applicable to various Boeing and McDonnell Douglas transport category airplanes, that currently requires revising the Airplane Flight Manual (AFM) to advise the flightcrew to don oxygen masks as a first and immediate step when the cabin altitude warning horn sounds. The actions specified by that AD are intended to prevent incapacitation of the flightcrew due to lack of oxygen, which could result in loss of control of the airplane. This amendment removes certain requirements for certain airplanes and revises the direction to the flightcrew to don oxygen masks as a first and immediate step when the cabin altitude warning occurs, rather than "when the cabin altitude warning horn sounds." This action is intended to address the identified unsafe condition.
