Airworthiness Directive · Amendment 39-23502 · Elevator tab control system
Ontic Engineering and Manufacturing, Inc. (Type Certificate Previously Held by Swearingen, Fairchild Aircraft, and M7 Aerospace) Airplanes
Quoted from the FAA's summary of this AD. The full text below is what applies.
This AD requires repetitively inspecting the pitch trim actuator for cracked, missing, or compromised sealant, replacing and sealing the pitch trim actuator if cracked, missing, or compromised, repetitively measuring the pitch trim actuator travel time, and depending on the results of the measurements, replacing and sealing the pitch trim actuator.
This AD also requires certain pitch trim actuators to be sealed after installation.
Certain Ontic Engineering and Manufacturing, Inc. Model SA226-T, SA226- AT, SA226-T(B), SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-PC, SA227-CC, SA227-DC (C-26B), and SA227-TT (300) airplanes. Serial numbers and exceptions
Does it apply to your aircraft?
Enter an N-number to see every AD that names its model. Serial numbers and installed parts still decide.
This AD applies to Ontic Engineering and Manufacturing, Inc. (type certificate previously held by Swearingen, Fairchild Aircraft, and M7 Aerospace) model and serial number airplanes, certificated in any category, as identified in paragraphs (c)(1) and (2) of this AD.
(1) Group 1 airplanes: Model SA226-T, SA226-AT, SA226-T(B), SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-PC, and SA227-TT (300) airplanes, all serial numbers with a pitch trim actuator Simmonds-Precision part number (P/N) DL5040M5, DL5040M6, or DL5040M8 installed.
(2) Group 2 airplanes: Model SA227-CC and SA227-DC (C-26B), all serial numbers with a pitch trim actuator Simmonds-Precision P/N DL5040M5, DL5040M6, or DL5040M8 installed.
The FAA is adopting a new airworthiness directive (AD) for certain Ontic Engineering and Manufacturing, Inc. Model SA226-T, SA226- AT, SA226-T(B), SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-PC, SA227-CC, SA227-DC (C-26B), and SA227-TT (300) airplanes. This AD was prompted by reports of in-flight pitch trim actuator failures. This AD requires repetitively inspecting the pitch trim actuator for cracked, missing, or compromised sealant, replacing and sealing the pitch trim actuator if cracked, missing, or compromised, repetitively measuring the pitch trim actuator travel time, and depending on the results of the measurements, replacing and sealing the pitch trim actuator. This AD also requires certain pitch trim actuators to be sealed after installation. The FAA is issuing this AD to address the unsafe condition on these products.
For the purpose of this AD:
(1) A new part is a pitch trim actuator with zero-hours time-in-service (TIS).
(2) An overhauled part is a pitch trim actuator that has zero hours TIS since the last overhaul.
(1) For all affected airplanes, at whichever compliance time in paragraph (h)(1)(i) or (ii) of this AD occurs later, inspect the ram of each actuator, specifically the pitch trim actuator rod ends, to determine if the sealant is cracked, missing, or compromised in accordance with Step 2.B.7, of the Accomplishment Instructions in Ontic Engineering and Manufacturing, Inc. SA227 Service Bulletin (SB) 227-27-067R3 dated March 2, 2026, (Ontic SB 227-27-067R3) or Ontic Engineering and Manufacturing, Inc. SA226 Service Bulletin 226-27-087R3 dated March 2, 2026, (Ontic SB 226-27-087R3), as applicable for your airplane.
(i) Within 1,000 flight hours or 6 calendar months since the pitch trim actuator was put into service, whichever occurs first; or
(ii) Within 30 days after the effective date of this AD.
(2) For affected airplanes with any pitch trim actuator whose rod ends have been found to have cracked, missing, or compromised sealant per the inspection in paragraph (h)(1) of this AD, and have at least 1,000 flight hours or at least 6 calendar months, whichever is less since the pitch trim actuator was put into service, before further flight, replace the pitch trim actuator with a new or overhauled pitch trim actuator and install and seal the pitch trim actuator in accordance with the Accomplishment Instructions, Step 2.B.8, Ontic SB 227-27-067R3 or Ontic SB 226-27-087R3, as applicable for your airplane.
(3) For affected airplanes with any pitch trim actuator whose rod ends have been found to have cracked, missing, or compromised sealant per the inspection in paragraph (h)(1) of this AD, and have less than 1,000 flight hours or 6 calendar months, whichever is less since the pitch trim actuator was put into service, before further flight, inspect and apply sealant to the pitch trim actuator in accordance with the Accomplishment Instructions, Step 2.B., of Ontic SB 227-27-067R3 or Ontic SB 226-27-087R3, as applicable for your airplane.
(4) For all affected airplanes, repetitively inspect and seal the pitch trim actuator every 1,000 flight hours or every 12 calendar months, whichever occurs first, after the inspection required in paragraph (h)(1), in accordance with the Accomplishment Instructions, Step 2.B., Ontic SB 227-27-067R3 or Ontic SB 226-27-087R3, as applicable for your airplane.
(5) For all affected airplanes, at whichever compliance time in paragraph (h)(1)(i) or (ii) of this AD occurs later, measure the pitch trim actuator travel time in accordance with the Accomplishment Instructions, Step 2.A., Ontic SB 227-27-067R3 or Ontic SB 226-27-087R3, as applicable for your airplane.
(i) If either pitch trim actuator rod does not meet travel time criteria, before further flight, replace the pitch trim actuator with a new or overhauled pitch trim actuator.
(ii) If both pitch trim actuator rods meet travel time criteria, repeat the measurement of the pitch trim actuator at intervals specified below in table 1 to paragraph (h)(5)(ii) of this AD.
| Condition | Repetitive measurement interval |
|---|---|
| For airplanes that have an original Simmonds-Precision pitch trim actuator, P/N DL5040M5, installed | Intervals not to exceed 250 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a replacement Simmonds-Precision pitch trim actuator, P/N DL5040M5, installed where both nut tube assemblies, P/N AA56142, were not replaced with new assemblies | Intervals not to exceed 250 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a replacement Simmonds-Precision pitch trim actuator, P/N DL5040M5, installed where both nut tube assemblies, P/N AA56142, were replaced with new assemblies | Intervals not to exceed 300 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a replacement Simmonds-Precision pitch trim actuator, P/N DL5040M6, installed. This part can be new, modified from a P/N DL5040M5 pitch trim actuator, or overhauled | Intervals not to exceed 300 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a Simmonds-Precision pitch trim actuator P/N DL5040M8, installed | Intervals not to exceed 300 flight hours or 6 calendar months, whichever occurs first. |
(6) If any affected pitch trim actuator was replaced with a pitch trim actuator that makes the airplane a Group 1 airplane, the actions of this AD still apply at the applicable compliance times.
(1) For all affected airplanes, at whichever compliance time in paragraph (i)(1)(i) or (ii) of this AD occurs later, inspect the ram of each actuator, specifically the pitch trim actuator rod ends, to determine if the sealant is cracked, missing, or compromised, in accordance with the Accomplishment Instructions, Step 2.B.7, SA227 Commuter Category Series Service Bulletin CC7-27-038R3, dated January 27, 2026 (Ontic SB CC7-27-038R3).
(i) Within 1,000 flight hours or 6 calendar months since the pitch trim actuator was put into service, whichever occurs first; or
(ii) Within 30 days after the effective date of this AD.
(2) For affected airplanes with any pitch trim actuator whose rod ends have been found to have cracked, missing, or compromised sealant per the inspection in paragraph (i)(1) of this AD, and have at least 1,000 flight hours or at least 6 calendar months, whichever is less since the pitch trim actuator was put into service, before further flight, replace the pitch trim actuator with a new or overhauled pitch trim actuator and install and seal the pitch trim actuator in accordance with the Accomplishment Instructions, Step 2.B.8, Ontic SB CC7-27-038R3.
(3) For affected airplanes with any pitch trim actuator whose rod ends have been found to have cracked, missing, or compromised sealant per the inspection in paragraph (i)(1) of this AD, and have less than 1,000 flight hours or 6 calendar months, whichever is less since the pitch trim actuator was put into service, before further flight, inspect and apply sealant to the pitch trim actuator in accordance with the Accomplishment Instructions, Step 2.B., Ontic SB CC7-27-038R3.
(4) For all affected airplanes, repetitively inspect and seal the pitch trim actuator every 1,000 flight hours or every 12 calendar months, whichever occurs first, after the inspection required in paragraph (i)(1), in accordance with the Accomplishment Instructions, Step 2.B., Ontic SB CC7-27-038R3.
(5) For all affected airplanes, at whichever compliance time in paragraph (i)(1)(i) or (ii) of this AD occurs later, measure the pitch trim actuator travel time in accordance with the Accomplishment Instructions, Step 2.A., Ontic SB CC7-27-038R3.
(i) If either pitch trim actuator rod does not meet travel time criteria, before further flight, replace the pitch trim actuator with a new or overhauled pitch trim actuator.
(ii) If both pitch trim actuator rods meet travel time criteria, repeat the measurement of the pitch trim actuator at intervals specified below in table 2 to paragraph (i)(5)(ii) of this AD.
| Condition | Repetitive measurement interval |
|---|---|
| For airplanes that have an original Simmonds-Precision pitch trim actuator, P/N DL5040M5, installed | Intervals not to exceed 250 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a replacement Simmonds-Precision pitch trim actuator, P/N DL5040M5, installed where both nut tube assemblies, P/N AA56142, were not replaced with new assemblies | Intervals not to exceed 250 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a replacement Simmonds-Precision pitch trim actuator, P/N DL5040M5, installed where both nut tube assemblies, P/N AA56142, were replaced with new assemblies | Intervals not to exceed 300 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a Simmonds-Precision pitch trim actuator, P/N DL5040M6, installed | Intervals not to exceed 300 flight hours or 6 calendar months, whichever occurs first. |
| For airplanes that have a Simmonds-Precision pitch trim actuator P/N DL5040M8, installed | Intervals not to exceed 300 flight hours or 6 calendar months, whichever occurs first. |
(6) If any affected pitch trim actuator was replaced with a pitch trim actuator that makes the airplane a Group 2 airplane, the actions of this AD still apply at the applicable compliance times.
As of the effective date of this AD, do not install a pitch trim actuator unless, upon installation, the procedures in Step 2.C Return to Service of each applicable Service Bulletin referenced in paragraphs (h)(1) or (i)(1) of this AD are followed.
Although the applicable Service Bulletins referenced in paragraphs (h)(1) and (i)(1) of this AD specify submission of certain information to the manufacturer, this AD does not include those reporting requirements.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.