Airworthiness Directive · Amendment 39-22926 · Fuselage
Airbus SAS Airplanes
This AD applies to Airbus SAS Model airplanes specified in paragraphs (c)(1) through (3) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2024-0089, dated April 15, 2024 (EASA AD 2024-0089).
(1) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes.
(2) Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes.
(3) Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes.
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and - 233 airplanes; and Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by a full-scale fatigue test that found cracks on the main landing gear (MLG) bay rear skin panel at the stringer run-out at Frame 46 and Stringer 32 on the left-hand and right-hand sides. This AD requires repetitive special detailed inspections (SDIs) of the affected area for cracking and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2024-0089.
(1) Where EASA AD 2024-0089 refers to its effective date, this AD requires using the effective date of this AD.
(2) Where paragraph (2) of EASA AD 2024-0089 specifies “If, during any inspection as required by paragraph (1) of this AD, discrepancies are detected, as defined in the SB, before next flight, contact Airbus for approved repair instructions and accomplish those instructions accordingly,” this AD requires replacing that text with “If, during any inspection as required by paragraph (1) of this AD, any cracking is found, before next flight, repair the cracking using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.”
(3) This AD does not adopt the “Remarks” section of EASA AD 2024-0089.
Although the material referenced in EASA AD 2024-0089 specifies to submit certain information to the manufacturer, this AD does not include that requirement.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD and email to: AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any material contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
For more information about this AD, contact Tim Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 206-231-3667; email: timothy.p.dowling@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
