Airworthiness Directive · Amendment 39-22860 · Equipment/furnishings
Airbus SAS Airplanes
This AD applies to Airbus SAS Model A350-941 and -1041 airplanes, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2024-0078, dated March 20, 2024 (EASA AD 2024-0078).
The FAA is superseding Airworthiness Directive (AD) 2023-07-13 which applied to certain Airbus SAS Model A350-941 and -1041 airplanes. AD 2023-07-13 required repetitive detailed inspections of the lower attachment studs on the AFT galley complex and, depending on findings, replacement of the lower attachment studs. This AD was prompted by a determination that additional airplanes are affected, and that all affected parts must be replaced with serviceable parts. This AD continues to require the actions in AD 2023-07-13, adds airplanes to the applicability, and requires the replacement of all affected parts; as specified in European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2024-0078.
(1) Where EASA AD 2024-0078 refers to “04 October 2022 [the effective date of EASA AD 2022-0196],” this AD requires using June 20, 2023 (the effective date of AD 2023-07-13).
(2) Where EASA AD 2024-0078 refers to its effective date, this AD requires using the effective date of this AD.
(3) Where paragraphs (1), (2), (3), and (4) of EASA AD 2024-0078 specify actions “in accordance with approved instructions issued by Airbus DOA,” this AD requires replacing that text with “in accordance with approved instructions issued by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.”
(4) This AD does not adopt the “Remarks” section of EASA AD 2024-0078.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, mail it to the address identified in paragraph (j) of this AD. Information may be emailed to: AMOC@faa.gov.
(i) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(ii) AMOCs approved previously for AD 2023-07-13 are approved as AMOCs for the corresponding provisions of EASA AD 2024-0078 that are required by paragraph (g) of this AD.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any material contains paragraphs that are labeled as RC, the instructions in RC paragraphs, including subparagraphs under an RC paragraph, must be done to comply with this AD; any paragraphs, including subparagraphs under those paragraphs, that are not identified as RC are recommended. The instructions in paragraphs, including subparagraphs under those paragraphs, not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the instructions identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to instructions identified as RC require approval of an AMOC.
For more information about this AD, contact Dat Le, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; email dat.v.le@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
Aircraft
