Airworthiness Directive · Amendment 39-22501 · Navigation
Bombardier, Inc., Airplanes
This AD applies to all Bombardier, Inc., Model BD-700-2A12 airplanes, certificated in any category.
The FAA is superseding Airworthiness Directive (AD) 2023-06- 13, which applied to all Bombardier, Inc., Model BD-700-2A12 airplanes. AD 2023-06-13 required revising the existing airplane flight manual (AFM) with new limitations to mitigate identified hazards due to interference from wireless broadband operations in the 3.7-3.98 GHz frequency band (5G C-Band) as identified by Notices to Air Missions (NOTAMs). Since the FAA issued AD 2023-06-13, the FAA determined that additional limitations are needed due to the continued deployment of new 5G C-Band stations whose signals are expected to cover most of the contiguous United States at transmission frequencies between 3.7-3.98 GHz. This AD requires revising the limitations section of the existing AFM to incorporate limitations prohibiting dispatch under certain master minimum equipment list (MMEL) items. The FAA is issuing this AD to address the unsafe condition on these products.
(1) For purposes of this AD, a “5G C-Band mitigated airport” (5G CMA) is an airport at which the telecommunications companies have agreed to voluntarily limit their 5G deployment at the request of the FAA, as identified by an FAA Domestic Notice.
(2) For purposes of this AD, a “radio altimeter tolerant airplane” is one for which the radio altimeter, as installed, demonstrates the tolerances specified in paragraphs (g)(2)(i) and (ii) of this AD, using a method approved by the FAA.
(i) Tolerance to radio altimeter interference, for the fundamental emissions (3.7-3.98 GHz), at or above the power spectral density (PSD) curve threshold specified in figure 1 to paragraph (g)(2)(i) of this AD.
(ii) Tolerance to radio altimeter interference, for the spurious emissions (4.2-4.4 GHz), at or above the PSD curve threshold specified in figure 2 to paragraph (g)(2)(ii) of this AD.
(3) For purposes of this AD, a “non-radio altimeter tolerant airplane” is one for which the radio altimeter, as installed, does not demonstrate the tolerances specified in paragraphs (g)(2)(i) and (ii) of this AD.
For non-radio altimeter tolerant airplanes, before further flight, revise the Limitations Section of the existing AFM to include the information specified in figure 3 to paragraph (h) of this AD. This may be done by inserting a copy of figure 3 to paragraph (h) of this AD into the existing AFM.
For radio altimeter tolerant airplanes, before further flight, revise the Limitations Section of the existing AFM to include the information specified in figure 4 to paragraph (i) of this AD. This may be done by inserting a copy of figure 4 to paragraph (i) of this AD into the existing AFM.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the Operational Safety Branch, send it to the attention of the person identified in paragraph (k)(2) of this AD. Information may be emailed to: AMOC@faa.gov.
(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(1) Refer to Transport Canada AD CF-2023-45, dated June 26, 2023, for related information. This Transport Canada AD may be found in the AD docket at regulations.gov under Docket No. FAA-2023-1407.
(2) For more information about this AD, contact Brett Portwood, Continued Operational Safety Technical Advisor, COS Program Management Section, Operational Safety Branch, FAA, 3960 Paramount Boulevard, Lakewood, CA 90712-4137; phone: 817-222-5390; email: operationalsafety@faa.gov.
