Airworthiness Directive · Amendment 39-22433 · Electrical power
Saab AB, Support and Services (Formerly Known as Saab AB, Saab Aeronautics) Airplanes
This AD applies to all Saab AB, Support and Services (Formerly Known as Saab AB, Saab Aeronautics) Model 340A (SAAB/SF340A) and SAAB 340B airplanes, certificated in any category.
The FAA is adopting a new airworthiness directive (AD) for all Saab AB, Support and Services Model 340A (SAAB/SF340A) and SAAB 340B airplanes. This AD was prompted by reports of excessive wear on certain starter generator brushes installed in the starter generator. This AD requires repetitive general visual inspections of the starter generator brushes installed in the starter generator and, depending on findings, replacement of the starter generator, and limits installation of affected generators, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2023-0073, dated April 5, 2023 (EASA AD 2023-0073).
(1) Where EASA AD 2023-0073 refers to its effective date, this AD requires using the effective date of this AD.
(2) This AD does not adopt the “Remarks” section of EASA AD 2023-0073.
(3) Paragraph (5) of EASA AD 2023-0073 specifies to report inspection results to SAAB AB within a certain compliance time. For this AD, report inspection results at the applicable time specified in paragraph (h)(3)(i) or (ii) of this AD.
(i) If the inspection was done on or after the effective date of this AD: Submit the report within 30 days after the inspection.
(ii) If the inspection was done before the effective date of this AD: Submit the report within 30 days after the effective date of this AD.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Saab AB, Support and Services' EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
For more information about this AD, contact Shahram Daneshmandi, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 206-231-3220; email Shahram.Daneshmandi@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
Aircraft
