Airworthiness Directive · Amendment 39-22297 · Landing gear
Airbus SAS Airplanes
This AD applies to all Airbus SAS airplanes identified in paragraphs (c)(1) through (7) of this AD, certificated in any category.
(1) Model A330-201, -202, -203, -223, -243 airplanes.
(2) Model A330-223F and -243F airplanes.
(3) Model A330-301, -302, -303, -321, -322, -323, -341, -342, and -343 airplanes.
(4) Model A330-841 airplanes.
(5) Model A330-941 airplanes.
(6) Model A340-211, -212, and -213 airplanes.
(7) Model A340-311, -312, and -313 airplanes.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200, A330-200 Freighter, A330-300, A330-800, A330-900, A340-200, and A340-300 series airplanes. This AD was prompted by a determination that certain landing gear parts have been manufactured with improper material or using a deviating manufacturing process. This AD requires replacing each affected part with a serviceable part, and for certain airplanes, re-assessing any previously repaired main landing gear (MLG) sliding piston, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2022-0049, dated March 21, 2022 (EASA AD 2022-0049).
(1) Where the affected part and serviceable part definitions in EASA AD 2022-0049 refer to “the SB,” replace the text “the SB” with “Airbus Service Bulletin A330-32-3302, dated January 18, 2022; or Airbus Service Bulletin A340-4321, dated January 18, 2022; as applicable.”
(2) Where EASA AD 2022-0049 refers to its effective date, this AD requires using the effective date of this AD.
(3) The “Remarks” section of EASA AD 2022-0049 does not apply to this AD.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
For more information about this AD, contact Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 206-231-3229; email vladimir.ulyanov@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
