Airworthiness Directive · Amendment 39-22285 · Placards and markings
Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
This AD applies to Airbus Canada Limited Partnership (Type certificate previously held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Model BD-500-1A10 and BD-500-1A11 airplanes, certificated in any category, as identified in Transport Canada AD CF-2022-01, dated January 7, 2022 (Transport Canada AD CF-2022-01).
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by reports of flight control (horizontal stabilizer, rudder, and elevator) decals degrading and peeling (damage), reports of operators painting over these decals, and reports that procedures to replace these decals were inaccurate, potentially causing incorrect positioning of replacement decals. This AD requires inspecting the left and right horizontal stabilizer decals for visibility and damage; and for certain airplanes, inspecting the rudder and left and right elevator decals for visibility and damage; and doing applicable corrective actions; as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, Transport Canada AD CF-2022-01.
(1) Where Transport Canada AD CF-2022-01 refers to its effective date, this AD requires using the effective date of this AD.
(2) Where Transport Canada AD CF-2022-01 refers to “hours air time,” this AD requires using “flight hours.”
(3) Where the service information referenced in Transport Canada AD CF-2022-01 specifies to inspect the decals and then perform a maintenance record review to determine the course of action, this AD allows the maintenance records review to be done first, and conditional actions, if any, are subsequently required, depending on the results of that records review.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New York ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, New York ACO Branch, FAA; or Transport Canada; or Airbus Canada Limited Partnership's Transport Canada Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
For more information about this AD, contact Gabriel Kim, Aerospace Engineer, Mechanical Systems and Administrative Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; email gabriel.d.kim@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
