Airworthiness Directive · Amendment 39-22264 · Windows
Airbus SAS Airplanes
This AD applies to all Airbus SAS airplanes identified in paragraphs (c)(1) through (6) of this AD, certificated in any category.
(1) Model A300 B2-1A, B2-1C, B2K-3C, B2-203, B4-2C, B4-103, and B4-203 airplanes.
(2) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes.
(3) Model A300 B4-605R and B4-622R airplanes.
(4) Model A300 C4-605R Variant F airplanes.
(5) Model A300 F4-605R and F4-622R airplanes.
(6) Model A310-203, -204, -221, -222, -304, -322, -324, and -325 airplanes.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 series airplanes; Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. This AD was prompted by a report that a Model A319 airplane lost the right-hand front windshield in flight. Due to the design similarity, this condition can also exist or develop on Model A300, A300-600, and A310 series airplanes. This AD requires repetitive inspections and electrical test measurements (ETMs) of the affected parts, and applicable corrective actions, and prohibits the installation of affected parts under certain conditions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2022-0058, dated March 28, 2022 (EASA AD 2022-0058).
(1) Where EASA AD 2022-0058 refers to its effective date, this AD requires using the effective date of this AD.
(2) Where Note 2 to paragraph (3) of EASA AD 2022-0058 specifies that, “operators may refer to the SB” when a lack of data impairs the determination of the windshield age or utilization, for this AD replace those words with “operators must refer to the SB”.
(3) Where paragraph (6) of EASA AD 2022-0058 refers to a “defect, as identified in the SB,” for purposes of this AD, defects include manufacturing variability, fretting between windshield components, water ingress, and electrical braids corrosion.
(4) This AD does not adopt the “Remarks” section of EASA AD 2022-0058.
Although paragraphs (11) and (12) of EASA AD 2022-0058 and the service information referenced therein specify to submit certain information to the manufacturer, this AD does not include that requirement.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
For more information about this AD, contact Dan Rodina, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 206-231-3225; email dan.rodina@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
