Airworthiness Directive · Amendment 39-22245 · Equipment/furnishings
Airbus SAS Airplanes
Superseded. A later AD replaced this one: AD 2024-24-09. Comply with the one in force.
This AD applies to all Airbus SAS Model airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category.
(1) Model A318-111, -112, -121, and -122 airplanes.
(2) Model A319-111, -112, -113, -114, -115, -131, -132, -133, -151N, -153N, and -171N airplanes.
(3) Model A320-211, -212, -214, -216, -231, -232, -233, -251N, -252N, -253N, -271N, -272N, and -273N airplanes.
(4) Model A321-111, -112, -131, -211, -212, -213, -231, -232, -251N, -251NX, -252N, -252NX, -253N, -253NX, -271N, -271NX, -272N, and -272NX airplanes.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by a report that damage (including delamination of the work deck, and corroded and cracked retainer blocks) was found during inspection of certain galleys. This AD requires repetitive inspections of certain galleys for corrosion of trolley retainer aluminum blocks and delamination of the upper panel of the trolley compartment, and applicable corrective action, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0183R1, dated September 20, 2021 (EASA AD 2021-0183R1).
(1) Where EASA AD 2021-0183R1 refers to its effective date, this AD requires using the effective date of this AD.
(2) Where EASA AD 2021-0183R1 refers to “18 August 2021,” this AD requires using the effective date of this AD.
(3) The “Remarks” section of EASA AD 2021-0183R1 does not apply to this AD.
(4) Where EASA AD 2021-0183R1 does not specify corrective action after a post-repair inspection that has findings of damage, this AD requires obtaining repair instructions before further flight from the FAA, EASA, or Airbus SAS's EASA Design Organization Approval (DOA) and accomplishing those actions accordingly. If approved by the DOA, the approval must include the DOA-authorized signature.
Although the service information referenced in EASA AD 2021-0183R1 specifies to submit certain information to the manufacturer, this AD does not include that requirement.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate If sending information directly to the manager, International Validation Branch, mail it to the address identified in paragraph (k) of this AD or email to: 9-AVS-AIR-730-AMOC@faa.gov. If mailing information, also submit information by email. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraphs (i) and (j)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
For more information about this AD, contact Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, FAA, International Validation Branch, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3229; email vladimir.ulyanov@faa.gov.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
