Airworthiness Directive · Amendment 39-22160 · Equipment/furnishings
Airbus SAS Airplanes
Superseded. A later AD replaced this one: AD 2023-20-12. Comply with the one in force.
This AD applies to the Airbus SAS airplanes specified in paragraphs (c)(1) through (3) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2022-0026, dated February 16, 2022 (EASA AD 2022-0026).
(1) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes.
(2) Model A320-211, -212, -214, -216, -231, -232, -233, -251N, and -271N airplanes.
(3) Model A321-111, -112, -131, -211, -212, -213, -231, -232, -251N, and -253N airplanes.
The FAA is superseding Airworthiness Directive (AD) 2019-26- 11, which applied to certain Airbus SAS Model A319-112, -115, and -132; A320-214, -216, -232, -233, -251N, and -271N; and A321-211, -231, -232, -251N, and -253N airplanes; and AD 2021-23-15, which applied to certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and - 133; A320-211, -212, -214, -216, -231, -232, and -233; and A321-111, - 112, -131, -211, -212, -213, -231, and -232 airplanes. AD 2019-26-11 required replacing the affected bumpers with serviceable bumpers. AD 2021-23-15 required modifying the waste compartment door of each affected galley. This AD was prompted by reports that the waste compartment door opened prematurely during a test, that container/ galley end stop bumpers were damaged in service, and that additional airplanes are subject to the unsafe conditions described in those ADs. This AD continues to require the actions in AD 2019-26-11 and AD 2021- 23-15, and adds airplanes to the applicability; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2022-0026.
(1) Where EASA AD 2022-0026 refers to December 11, 2018 (the effective date of EASA AD 2018-0255), this AD requires using January 10, 2022 (the effective date of AD 2021-23-15).
(2) Where EASA AD 2022-0026 refers to May 29, 2019 (the effective date of EASA AD 2019-0106), this AD requires using March 12, 2020 (the effective date of AD 2019-26-11).
(3) Where EASA AD 2022-0026 refers to its effective date, this AD requires using the effective date of this AD.
(4) The “Remarks” section of EASA AD 2022-0026 does not apply to this AD.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
