Airworthiness Directive · Amendment 39-22156 · Equipment/furnishings
Airbus SAS Airplanes
This AD applies to the Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category.
(1) All Model A318-111, A318-112, A318-121, and A318-122 airplanes.
(2) All Model A319-111, A319-112, A319-113, A319-114, A319-115, A319-131, A319-132, A319-133, A319-151N, A319-153N, and A319-171N airplanes.
(3) All Model A320-211, A320-212, A320-214, A320-216, A320-231, A320-232, A320-233, A320-251N, A320-252N, A320-253N, A320-271N, A320-272N, and A320-273N airplanes.
(4) All Model A321-111, A321-112, A321-131, A321-211, A321-212, A321-213, A321-231, A321-232, A321-251N, A321-251NX, A321-252N, A321-252NX, A321-253N, A321-253NX, A321-271N, A321-271NX, A321-272N, and A321-272NX airplanes.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by unclear and incomplete placard instructions for the doghouse door lock. This AD requires installing improved handling instruction placards on affected doghouses and re-identifying the doghouses, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected doghouses under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0279, dated December 15, 2021 (EASA AD 2021-0279).
(1) Where EASA AD 2021-0279 refers to its effective date, this AD requires using the effective date of this AD.
(2) The “Remarks” section of EASA AD 2021-0279 does not apply to this AD.
(3) Where paragraph (1) of EASA AD 2021-0279 refers to affected airplanes, replace the text “For Group 1 aeroplanes” with “Group 1 airplanes except for airplanes identified in paragraph (2) of EASA AD 2021-0279.”
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
Aircraft
