Airworthiness Directive · Amendment 39-22125 · Fuselage
Airbus SAS Airplanes
Superseded. A later AD replaced this one: AD 2025-23-09. Comply with the one in force.
This AD applies to Airbus SAS airplanes specified in paragraphs (c)(1) through (4) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2022-0030, dated February 25, 2022 (EASA AD 2022-0030).
(1) Model A318-111, -112, -121, and -122 airplanes.
(2) Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes.
(3) Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes.
(4) Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes.
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A318 series airplanes; Model A319-111, -112, - 113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes; and Model A321-111, -112, - 131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by a report that cracks were found on the web horizontal flange and inner cap on a certain frame (FR), left-hand (LH) and right-hand (RH) sides, at a certain stringer (STGR). This AD requires repetitive high frequency eddy current (HFEC) inspections for cracks on the web horizontal flange and inner cap, and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2022-0030.
(1) Where EASA AD 2022-0030 refers to its effective date, this AD requires using the effective date of this AD.
(2) The “Remarks” section of EASA AD 2022-0030 does not apply to this AD.
(3) Where paragraph (2) of EASA AD 2022-0030 specifies “Accomplishment on an aeroplane of (repetitive) maintenance instructions, issued and approved by Airbus,” for this AD, those instructions must have been approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(4) Where paragraph (3) of EASA AD 2022-0030 specifies if “discrepancies and/or cracks are detected, before next flight, contact Airbus for approved corrective action(s) instructions and, within the compliance time specified therein, accomplish those instructions accordingly,” for this AD, if cracks are detected, the cracks must be repaired before further flight using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
(5) Where paragraph (4) of EASA AD 2022-0030 specifies “the instructions provided by Airbus,” for this AD, those instructions must be approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch of the certification office, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
