Airworthiness Directive · Amendment 39-22111 · Time limits/maintenance checks
Airbus SAS Airplanes
Superseded. A later AD replaced this one: AD 2024-16-02. Comply with the one in force.
This AD applies to all Airbus SAS Model A300 B4-601, B4-603, B4-620, B4-622 B4-605R, B4-622R, C4-605R Variant F, F4-605R, and F4-622R airplanes, certificated in any category.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0258, dated November 17, 2021 (EASA AD 2021-0258).
(1) Where EASA AD 2021-0258 refers to its effective date, this AD requires using the effective date of this AD.
(2) Where paragraph (1) of EASA AD 2021-0258 specifies “This AD invalidates the LOV [limit of validity] as specified in Airbus A300-600 ALS Part 2 Revision 03 [EASA AD 2019-0090],” this AD replaces the LOVs specified in paragraph 3.1 of Airbus A300-600 Airworthiness Limitations Section (ALS), Part 2, “Damage Tolerant Airworthiness Limitation Items (DT-ALI),” Revision 03, dated December 14, 2018, as required by FAA AD 2019-21-01.
(3) Paragraph (2) of EASA AD 2021-0258 specifies revising “the approved AMP” within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD.
(4) The “Remarks” section of EASA AD 2021-0258 does not apply to this AD.
After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals are allowed unless they are approved as specified in the provisions of the “Ref. Publications” section of EASA AD 2021-0258.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
